Home › General › MAINTENANCE › REAR DISC BRAKE PAD
RM37H0E _V1 General _095083 MAINTENANCE _0455454 REAR DISC BRAKE PAD A

MAINTENANCE  REAR DISC BRAKE PAD  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C450044N05
3.667,4.354 5.281,5.646 1.615,1.292 0.083,2.667 1.563,3.969 1.479,1.302 1.688,3.469 3.438,5.042 1.75,1.573 1.281,0.781 3.958,2.365 2.677,1.583 2.438,4.854 2.438,4.188 true 2.01,4.854 2.844,4.854 2.844,4.854 2.844,4.604 true 4.344,4.75 4.094,4.75 true 4.521,5.385 4.323,5.385 true 0.854,3.583 1.104,3.583 true 0.698,2.927 0.948,2.927 true 3,2.083 3,1.25 3,1.25 2.667,1.25 true 2.656,1.833 2.99,1.833 false 1.719,1.417 1.969,1.417 true 3.521,2.667 2.354,2.667 2.354,2.667 2.354,2.729 true 3.052,3.104 3.052,2.677 true 4.667,4.083 4.5,4.083 4.5,4.083 4.5,4.333 false 1.073,3.99 1.073,4.323 1.073,4.323 0.906,4.323 false 2.604,5.052 2.604,5.354 2.604,5.354 2.438,5.354 false 3.385,1.5 3.635,1.5 true 0.938,1.198 1.271,1.198 false 4.406,4.667 4.719,4.865 0.313,0.198 10 false *1 0.635,3.51 0.896,3.708 0.26,0.198 10 false *1 1.021,2.865 1.292,3.104 0.271,0.24 10 false *2 4.104,5.323 4.323,5.521 0.219,0.198 10 false *2 1.49,1.333 1.781,1.615 0.292,0.281 10 false *3 2.938,2.156 3.229,2.438 0.292,0.281 10 false *4 3.708,1.406 4,1.688 0.292,0.281 10 false *5 3.615,2.604 3.906,2.885 0.292,0.281 10 false *6 2.198,5.208 2.5,5.521 0.302,0.313 18 false 2 5,3.948 5.313,4.281 0.313,0.333 18 false 1 0.635,4.188 0.948,4.521 0.313,0.333 18 false 1 1.781,4.771 2.094,4.969 0.313,0.198 10 false *7 0.708,1.031 1.021,1.365 0.313,0.333 18 false 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REAR DISC BRAKE ANTI-SQUEAL SHIM 04946 (Click here) - -
2 REAR DISC BRAKE PAD KIT 04466 (Click here) - -
3 REAR DISC BRAKE FITTING KIT 04948 - - -

*1 NO. 1 ANTI-SQUEAL SHIM *2 NO. 2 ANTI-SQUEAL SHIM
*3 PIN HOLD CLIP *4 HOLE PIN
*5 NO. 1 ANTI-RATTLE SPRING *6 INNER ANTI-RATTLE SPRING
*7 REAR DISC BRAKE PAD - -
V100135

Disc brake grease
V100136

Grease

C450043N06
6.438,0.188 6.854,0.188 false 6.458,0.604 6.813,0.604 false 4.667,1.24 4.792,1.01 4.792,1.01 4.958,1.01 true 6.479,1.052 6.833,1.052 false 6.208,0.052 6.49,0.365 0.281,0.313 18 false 4 5.031,0.875 5.365,1.229 0.333,0.354 18 false 6 6.271,0.469 6.615,0.781 0.344,0.313 18 false 7 6.25,0.906 6.542,1.188 0.292,0.281 18 false 5

Procedure Part Name Code
Z101186

Z101188

Z101187

4 CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL - (Click here) - -
5 INSPECT BRAKE FLUID LEVEL IN RESERVOIR - - (Click here) -
6 REAR WHEEL - - - -
7 INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL - - - (Click here)

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The following procedure is for the LH side.



NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the rear disc brake pads, the brake pedal may feel soft due to clearance between the rear disc brake pads and rear disc. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the rear disc brake pads, always perform a road test to check the braking performance and check for vibrations.

·

When removing or installing the rear disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



PROCEDURE

Hide 04946 1.INSTALL REAR DISC BRAKE ANTI-SQUEAL SHIM

a.
C450049C02
4.75,2.167 4.75,1.583 true 3.583,0.583 3.583,0.417 3.583,0.417 3.75,0.417 true 4.083,0.917 4.083,0.583 4.083,0.583 4.25,0.583 true 5.25,1.917 5.25,2.167 5.25,2.167 4.333,2.167 true 5.917,2.135 5.917,2.417 5.917,2.417 5.75,2.417 true 6.667,2.052 6.667,1.833 6.667,1.833 6.833,1.833 true 4.833,0.521 4.833,0.333 4.833,0.333 5.75,0.333 true 5.417,0.813 5.417,0.333 true 0.417,0.042 0.698,0.396 0.281,0.354 18 false i 2.854,0.042 3.854,0.385 1,0.344 18 false ii, iii, iv 4.115,2.094 4.427,2.25 0.313,0.156 10 false *1 4.323,0.5 4.635,0.656 0.313,0.156 10 false *2 3.802,0.344 4.021,0.552 0.219,0.208 10 false *3 5.823,0.26 6.052,0.51 0.229,0.25 10 false *4 5.563,2.344 5.823,2.552 0.26,0.208 10 false *2 6.896,1.76 7.115,1.969 0.219,0.208 10 false *3
*1 Rear Disc Brake Pad *2 No. 1 Anti-Squeal Shim
*3 No. 2 Anti-Squeal Shim *4 Inner Anti-Rattle Spring
V100135

Grease
V100136

Disc Brake Grease


i.

Apply a light coat of grease to the rear disc brake pads as shown in the illustration.

NOTICE:
·

When applying grease, use the grease enclosed with a rear disc brake pad kit or supplied grease (Part No. 90999-94254) or equivalent.

·

Keep the lining surface of the rear disc brake pad free from grease.




ii.

Apply disc brake grease to the rear disc brake pads and No. 1 anti-squeal shims at the positions shown in the illustration.

NOTICE:
·

Use the grease supplied with the anti-squeal shim kit or disc brake grease as the disc brake grease.

·

Keep the lining surface of the rear disc brake pad free from grease.

·

Do not apply grease between the No. 1 and No. 2 anti-squeal shims.




iii.

Install the inner anti-rattle springs to each of the rear disc brake pads.


iv.

Install the No. 1 and No. 2 anti-squeal shims to each of the rear disc brake pads.



Hide 04466 2.INSTALL REAR DISC BRAKE PAD KIT

Z101186

CAUTION:

Be careful not to get pinched by the disc brake cylinder assembly or other parts when installing the rear disc brake pads.



a.
C452185N01
2.021,1.219 2.271,1.469 2.271,1.469 2.438,1.469 true 2.531,1.396 2.844,1.604 0.313,0.208 10 true SST 0.396,0.083 0.75,0.469 0.354,0.385 18 false i 4.021,0.094 4.375,0.479 0.354,0.385 18 false ii

i.

Using SST, push back the rear disc brake piston.

SST
09719-77010  

NOTICE:
·

Make sure the brake fluid does not overflow from the reservoir.

·

Do not forcibly push in the rear disc brake piston.




ii.

Install the 2 rear disc brake pads to the rear disc brake cylinder assembly LH.



Hide 04948 3.INSTALL REAR DISC BRAKE FITTING KIT

a.
C452186N01
2.656,0.833 2.813,1.031 0.156,0.198 10 true A 4.302,0.823 4.458,1.021 0.156,0.198 10 true A 4.385,0.448 4.542,0.646 0.156,0.198 10 false B 4.396,1.167 4.552,1.365 0.156,0.198 10 false B 1.073,0.531 1.229,0.729 0.156,0.198 10 false B 1.063,1.177 1.219,1.375 0.156,0.198 10 false B 0.167,0.083 0.688,0.385 0.521,0.302 18 false i, ii 3.667,0.083 4,0.333 0.333,0.25 18 false iii

i.

Install the No. 1 anti-rattle spring to the rear disc brake cylinder LH.


ii.

While pressing the area (A), install the 2 hole pins (B).


iii.

While pressing the area (A), slightly pull out the hole pin (B) from the rear disc brake cylinder assembly LH, and install the pin hold clip.



Hide 4.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Z101186

Click here(Click here)

Hide 5.INSPECT BRAKE FLUID LEVEL IN RESERVOIR

Hide 6.INSTALL REAR WHEEL

Hide 7. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART