Home › Suspension › REAR SUSPENSION › REAR UPPER ARM
RM37H0E _53 Suspension _097406 REAR SUSPENSION _0455874 REAR UPPER ARM A

REAR SUSPENSION  REAR UPPER ARM  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C448160N02
0.917,1.583 0.917,0.469 0.917,0.469 1.083,0.469 true 3.323,1.219 3.323,0.75 3.323,0.75 3.49,0.75 true 4.385,2.688 4.719,2.688 true 2.167,1.51 2.167,1.01 2.167,1.01 2.333,1.01 true 4.51,1.667 4.51,1.104 4.51,1.104 4.677,1.104 true 5.865,3.354 5.865,2.792 5.865,2.792 6.031,2.792 true 6.104,2.635 6.385,2.99 0.281,0.354 18 false 1 1.563,0.313 1.844,0.667 0.281,0.354 18 false 2 4.792,2.521 5.073,2.875 0.281,0.354 18 false 3 2.417,0.938 2.625,1.125 0.208,0.188 10 false ● 4.74,1.021 4.948,1.208 0.208,0.188 10 false ● 3.896,0.625 4.177,0.979 0.281,0.354 18 false 4

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REAR TIRE LH - - - -
2 REAR NO. 1 SUSPENSION ARM ASSEMBLY LH 48720A (Click here) - -
3 REAR SHOCK ABSORBER ASSEMBLY LH 48540 - - -
4 REAR UPPER CONTROL ARM ASSEMBLY LH 48790 (Click here) - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the rear upper arm removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced:
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link

*: The vehicle height changes because of suspension or tire replacement.

Suspension, tires, etc.*
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Parking support brake system

·

Advanced park


w/ Advanced Park:
(Click here)
w/o Advanced Park:
(Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle

·

Rear television camera view adjustment (for Rear camera detection system)


Panoramic view monitor system (Click here)
Perform headlight ECU sub-assembly LH initialization Automatic headlight beam level control system (Click here)
Wheel alignment adjustment Perform "Calibration" Electronically controlled brake system malfunctions (Click here)


HINT:
·

Use the same procedure for the RH and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.INSTALL REAR TIRE LH

Hide 48720A 2.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

a.
C446785C01
6.281,2.75 6.417,2.417 6.417,2.417 6.583,2.417 true 1.417,2.583 1.75,2.583 true 5.063,2.885 4.833,2.5 4.833,2.5 4.667,2.5 true 5.135,3.177 4.948,3.438 4.948,3.438 5.177,3.219 true 5.635,2.677 5.417,2.25 5.417,2.25 5.25,2.25 true 1.958,2.115 2.375,2.115 true 6,3.385 6.083,3.5 6.083,3.5 6.167,3.5 true 4.813,3.427 5.042,3.594 0.229,0.167 10 false *a 4.531,3.052 4.823,3.302 0.292,0.25 10 false *b 4.49,2.417 4.75,2.646 0.26,0.229 10 false *c 5.063,2.177 5.313,2.427 0.25,0.25 10 false *d 6.469,3.01 6.719,3.26 0.25,0.25 10 false *g 6.229,3.427 6.458,3.594 0.229,0.167 10 false *e 6.646,2.344 6.896,2.594 0.25,0.25 10 false *f 1,2.5 1.344,2.688 0.344,0.188 10 true SST 1.656,2.01 1.917,2.208 0.26,0.198 10 true *h 2.031,0.125 2.365,0.417 0.333,0.292 18 false i 0.615,2 1.104,2.302 0.49,0.302 18 true ii, iii
*a SST (Spacer A) *b 1 mm (0.0394 in.)
*c Spacer *d Center Nut
*e Body *f Claw
*g Parallel *h String


i.

Remove the nut.


ii.

Install 2 SST (spacer A) onto the rear No. 1 suspension arm assembly LH so that there is a space of approximately 1 mm (0.0394 in.) between the arm and spacers.

SST
09960-20010  (09961-02050)

NOTICE:
·

Make sure to install the spacers (SST spacer A) as the rear axle carrier sub-assembly LH spacer may shift.

·

As SST may become damaged, make sure the space between the arm and spacers is not 1 mm (0.0394 in.) or less.




iii.

Using SST, disconnect the rear No. 1 suspension arm assembly LH from the rear axle carrier sub-assembly LH.

SST
09960-20010  (09961-02010)

NOTICE:
·

Apply molybdenum grease to the bolt threads and end of the SST bolt.

·

Do not damage the dust cover.

·

As the dust cover may be damaged, adjust SST with the center nut so that the body and claw are parallel.

·

Make sure to tie the string of SST to the vehicle to prevent SST from dropping.





b.
C447165C01
0,0 0,0 false
V100135

Bolt
V100136

Nut



Hide 48540 3.REMOVE REAR SHOCK ABSORBER ASSEMBLY LH

Hide 48790 4.REMOVE REAR UPPER CONTROL ARM ASSEMBLY LH

a.
C446787C01
6.188,2.75 6.417,2.417 6.417,2.417 6.583,2.417 true 2.521,2.75 2.854,2.75 true 5.167,2.896 4.938,2.51 4.938,2.51 4.771,2.51 true 5.229,3.156 5.042,3.417 5.042,3.417 5.271,3.198 true 5.615,2.708 5.417,2.24 5.417,2.24 5.25,2.24 true 1.26,2.125 1.677,2.125 true 5.969,3.344 6.052,3.458 6.052,3.458 6.135,3.458 true 4.917,3.406 5.146,3.573 0.229,0.167 10 false *a 4.698,3.063 4.99,3.313 0.292,0.25 10 false *b 4.583,2.448 4.844,2.677 0.26,0.229 10 false *c 5.063,2.177 5.313,2.427 0.25,0.25 10 false *d 6.385,3 6.635,3.25 0.25,0.25 10 false *g 6.188,3.396 6.417,3.563 0.229,0.167 10 false *e 6.646,2.344 6.896,2.594 0.25,0.25 10 false *f 2.948,2.688 3.292,2.875 0.344,0.188 10 true SST 1.656,2.01 1.917,2.208 0.26,0.198 10 true *h 2.031,0.083 2.365,0.375 0.333,0.292 18 false i 0.51,2.021 0.958,2.313 0.448,0.292 18 true ii, iii
*a SST (Spacer A) *b 1 mm (0.0394 in.)
*c Spacer *d Center Nut
*e Body *f Claw
*g Parallel *h String


i.

Remove the nut.


ii.

Install 2 SST (spacer A) onto the rear upper control arm assembly LH so that there is a space of approximately 1 mm (0.0394 in.) between the arm and spacers.

SST
09960-20010  (09961-02050)

NOTICE:
·

Make sure to install the spacers (SST spacer A) as the rear axle carrier sub-assembly LH spacer may shift.

·

As SST may become damaged, make sure the space between the arm and spacers is not 1 mm (0.0394 in.) or less.




iii.

Using SST, disconnect the rear upper control arm assembly LH from the rear axle carrier sub-assembly LH.

SST
09960-20010  (09961-02010)

NOTICE:
·

Apply molybdenum grease to the bolt threads and end of the SST bolt.

·

Do not damage the dust cover.

·

As the dust cover may be damaged, adjust SST with the center nut so that the body and claw are parallel.

·

Make sure to tie the string of SST to the vehicle to prevent SST from dropping.





b.
C447168C01
0,0 0,0 false
V100135

Bolt
V100136

Nut