Home › Suspension › REAR SUSPENSION › REAR UPPER ARM
RM37H0E _53 Suspension _097406 REAR SUSPENSION _0455874 REAR UPPER ARM A

REAR SUSPENSION  REAR UPPER ARM  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C447162N04
4.74,1.927 5.781,2.115 1.042,0.188 4.531,0.885 5.74,1.49 1.208,0.604 4.688,1.854 5.854,2.188 1.167,0.333 2.26,0.146 3.292,0.552 1.031,0.406 2.208,0.073 3.365,0.604 1.156,0.531 4.615,0.969 5.667,1.417 1.052,0.448 1.917,1.792 3.167,2.396 1.25,0.604 1.99,1.865 3.083,2.313 1.094,0.448 0.958,1.563 0.958,0.469 0.958,0.469 1.125,0.469 true 3.354,1.229 3.354,0.771 3.354,0.771 3.49,0.771 true 6.458,0.25 6.75,0.25 true 4.063,1.177 4.615,1.177 true 2.156,1.49 2.156,0.344 2.156,0.344 2.26,0.344 true 4.406,2.958 4.698,2.958 true 0.49,2.094 1.99,2.094 false 4.49,1.74 4.49,2.021 4.49,2.021 4.74,2.021 true 5.854,3.344 5.854,2.885 5.854,2.885 5.99,2.885 true 3.854,0.625 4.417,0.958 0.563,0.333 18 false 1, 5 4.76,2.833 5.042,3.188 0.281,0.354 18 false 2 1.563,0.313 2.146,0.656 0.583,0.344 18 false 3, 6 5.698,0.125 6.635,0.406 0.938,0.281 18 false 4, 8, 9 4.677,1.01 5.688,1.177 1.01,0.167 8 false 133 (1356, 98) 4.698,1.188 5.583,1.375 0.885,0.188 8 false 96.7 (986, 71)* 4.802,1.938 5.698,2.104 0.896,0.167 8 false 165 (1683, 122) 5.917,1.927 6.073,2.125 0.156,0.198 10 false ● 2.302,0.188 3.417,0.354 1.115,0.167 8 false 160 (1632, 118) 2.292,0.354 3.292,0.521 1,0.167 8 false 116.4 (1187, 86)* 3.417,0.208 3.604,0.406 0.188,0.198 10 false ● 2.063,1.927 3,2.073 0.938,0.146 8 true 204 (2080, 150) 2.031,2.115 3.042,2.281 1.01,0.167 8 true 163.3 (1665, 120)* 6.042,2.719 6.385,3.083 0.344,0.365 18 false 7

Procedure Part Name Code
Z101186

Z101188

Z101187

1 TEMPORARILY TIGHTEN REAR UPPER CONTROL ARM ASSEMBLY LH 48720A (Click here) - -
2 REAR SHOCK ABSORBER ASSEMBLY LH 48540 - - -
3 TEMPORARILY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY LH 48790 (Click here) - -
4 STABILIZE SUSPENSION - - - (Click here)
5 FULLY TIGHTEN REAR UPPER CONTROL ARM ASSEMBLY LH 48720A (Click here) - -
6 FULLY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY LH 48790 (Click here) - -
7 REAR TIRE LH - - - -
8 INSPECT AND ADJUST REAR WHEEL ALIGNMENT - - - -
9 PERFORM INITIALIZATION - - - (Click here)

V111893C24
0,0 0,0 false

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) - -
● Non-reusable part * For use with ball joint lock nut wrench

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 48790 1.TEMPORARILY TIGHTEN REAR UPPER CONTROL ARM ASSEMBLY LH

a.
C447169C01
0.396,0.063 0.677,0.417 0.281,0.354 18 true i 3.625,0.042 3.906,0.396 0.281,0.354 18 false ii
V100135

Bolt
V100136

Nut


i.

Insert the bolt from the front of the vehicle. Then temporarily tighten the rear upper control arm assembly LH with the nut and washer.


ii.

Temporarily tighten the rear upper control arm assembly LH to the rear axle carrier sub-assembly LH with a new nut.



Hide 48540 2.INSTALL REAR SHOCK ABSORBER ASSEMBLY LH

Hide 48720A 3.TEMPORARILY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

a.
C447169C01
0.396,0.063 0.677,0.417 0.281,0.354 18 true i 3.625,0.042 3.906,0.396 0.281,0.354 18 false ii
V100135

Bolt
V100136

Nut


i.

Insert the bolt from the back of the vehicle. Then temporarily tighten the rear No. 1 suspension arm assembly LH with the nut and washer.


ii.

Temporarily tighten the rear No. 1 suspension arm assembly LH to the rear axle carrier sub-assembly LH with a new nut.



Hide 4.STABILIZE SUSPENSION

Z101186

Click here(Click here)

Hide 48790 5.FULLY TIGHTEN REAR UPPER CONTROL ARM ASSEMBLY LH

a.
C447172C01
2.656,1.74 2.969,1.938 0.313,0.198 10 false *a 0.427,0.063 0.708,0.417 0.281,0.354 18 true i 3.656,0.042 3.938,0.396 0.281,0.354 18 true ii
*a Torque Wrench Fulcrum Length - -


i.

Using a ball joint lock nut wrench, fully tighten the rear upper control arm assembly LH with the nut.

Torque:
Specified tightening torque : 133 N*m (1356 kgf*cm, 98 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a ball joint lock nut wrench (fulcrum length of 150 mm (5.906 in.)) + torque wrench (fulcrum length of 400 mm (15.748 in.)): 96.7 N*m (986 kgf*cm, 71 ft.*lbf)




ii.

Fully tighten the nut.

Torque:
165 N*m (1683 kgf*cm, 122 ft.*lbf)



Hide 48720A 6.FULLY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

a.
C447173C01
0.865,1.667 1.177,1.865 0.313,0.198 10 false *a 6.042,0.583 6.354,0.781 0.313,0.198 10 true *a 0.375,0.073 0.656,0.427 0.281,0.354 18 true i 4.094,0.063 4.5,0.417 0.406,0.354 18 true ii
*a Torque Wrench Fulcrum Length - -


i.

Using a ball joint lock nut wrench, fully tighten the rear upper control arm assembly LH with the nut.

Torque:
Specified tightening torque : 204 N*m (2080 kgf*cm, 150 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a ball joint lock nut wrench (fulcrum length of 149.75 mm (5.896 in.)) + torque wrench (fulcrum length of 600 mm (23.622 in.)): 163.3 N*m (1665 kgf*cm, 120 ft.*lbf)




ii.

Using a ball joint lock nut wrench, fully tighten the nut.

Torque:
Specified tightening torque : 160 N*m (1632 kgf*cm, 118 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a ball joint lock nut wrench (fulcrum length of 150 mm (5.906 in.)) + torque wrench (fulcrum length of 400 mm (15.748 in.)): 116.4 N*m (1187 kgf*cm, 86 ft.*lbf)





Hide 7.INSTALL REAR TIRE LH

Hide 8.INSPECT AND ADJUST REAR WHEEL ALIGNMENT