Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)
RM37H0E _58 Vehicle Interior _095292 SEAT _0457023 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2652  Front Vertical Sensor Malfunction  


DESCRIPTION

When the position control ECU assembly LH (for LHD) or RH (for RHD) does not receive a front vertical motor position sensor signal despite the seat having been moved upward or downward by power seat motor operation, this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B2652 Front Vertical Sensor Malfunction Front vertical motor position sensor signal not received when power seat moved upward or downward.
·

Position control ECU assembly LH (for LHD)

·

Position control ECU assembly RH (for RHD)

·

Power seat tilt motor assembly LH (for LHD)

·

Power seat tilt motor assembly RH (for RHD)

·

Harness or connector


Driver Seat A

WIRING DIAGRAM

for LHD:


E418043E38
4.896,0.646 5.229,0.875 0.333,0.229 10 false L41 4.917,1.156 5.292,1.417 0.375,0.26 10 false L42 4.906,1.688 5.24,1.906 0.333,0.219 10 false L43 4.896,2.188 5.229,2.385 0.333,0.198 10 false L43 2.427,0.552 2.635,0.823 0.208,0.271 10 false 1 2.438,1.063 2.656,1.333 0.219,0.271 10 false 4 2.448,1.594 2.667,1.823 0.219,0.229 10 false 2 2.448,2.115 2.719,2.396 0.271,0.281 10 false 3 4.979,0.417 5.167,0.635 0.188,0.219 10 false 7 4.979,0.938 5.208,1.188 0.229,0.25 10 false 4 4.948,1.448 5.25,1.688 0.302,0.24 10 false 10 4.938,1.979 5.208,2.219 0.271,0.24 10 false 12 1.021,2.594 1.354,2.854 0.333,0.26 10 false L27 5.25,2.708 6.479,3.396 1.229,0.688 10 false Position Control ECU Assembly LH 1.01,2.781 3.365,3.25 2.354,0.469 10 false Power Seat Tilt Motor Assembly LH (Front Vertical Motor) 5.313,0.688 5.927,0.885 0.615,0.198 10 false FRV+ 5.302,1.219 5.917,1.417 0.615,0.198 10 false FRV- 5.313,1.719 5.927,1.917 0.615,0.198 10 false SSFV 5.302,2.229 5.917,2.427 0.615,0.198 10 false SGND


for RHD:


E418043E37
4.896,0.646 5.229,0.875 0.333,0.229 10 false L15 4.917,1.156 5.26,1.354 0.344,0.198 10 false L16 4.906,1.688 5.24,1.906 0.333,0.219 10 false L17 4.906,2.188 5.24,2.385 0.333,0.198 10 false L17 2.427,0.552 2.635,0.823 0.208,0.271 10 false 1 2.438,1.063 2.656,1.333 0.219,0.271 10 false 4 2.448,1.594 2.667,1.823 0.219,0.229 10 false 2 2.448,2.115 2.719,2.396 0.271,0.281 10 false 3 4.979,0.417 5.167,0.635 0.188,0.219 10 false 7 4.979,0.938 5.208,1.188 0.229,0.25 10 false 4 4.948,1.448 5.25,1.688 0.302,0.24 10 false 10 4.938,1.979 5.208,2.219 0.271,0.24 10 false 12 1.021,2.594 1.354,2.854 0.333,0.26 10 false L2 5.25,2.708 6.479,3.396 1.229,0.688 10 false Position Control ECU Assembly RH 1,2.76 3.271,3.25 2.271,0.49 10 false Power Seat Tilt Motor Assembly RH (Front Vertical Motor) 5.313,0.688 5.927,0.885 0.615,0.198 10 false FRV+ 5.302,1.219 5.917,1.417 0.615,0.198 10 false FRV- 5.313,1.719 5.927,1.917 0.615,0.198 10 false SSFV 5.302,2.229 5.917,2.427 0.615,0.198 10 false SGND


CAUTION / NOTICE / HINT

*1: for LHD

*2: for RHD


NOTICE:

Initializing the position control ECU assembly LH*1 or RH*2 will clear the seat position memory.


HINT:

Make sure to initialize the position control ECU assembly LH*1 or RH*2 after replacing the seat assembly or any related parts (including removal and installation).

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>REGISTRATION


PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.CLEAR DTC

B

9.CLEAR DTC
2.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Driver Seat > Clear DTCs
50002 162

Result:
Proceed to
NEXT



NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Driver Seat > Trouble Codes
50001 162

Result:
Result Proceed to
B2652 is not output A
B2652 is output B



A

B

4.PERFORM ACTIVE TEST USING GTS (FRONT VERTICAL OPERATION)
4.PERFORM ACTIVE TEST USING GTS (FRONT VERTICAL OPERATION)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Front Vertical Operation Seat front vertical operation OFF/Down/Up -
Body Electrical > Driver Seat > Active Test
Tester Display
Front Vertical Operation
50004 162 3
OK:

Front vertical motor operates normally.



Result:
Proceed to
OK
NG



OK

5.CHECK POSITION CONTROL ECU ASSEMBLY LH (FRONT VERTICAL MOTOR CIRCUIT)

NG

7.INSPECT POWER SEAT TILT MOTOR ASSEMBLY LH (FRONT VERTICAL MOTOR)
5.CHECK POSITION CONTROL ECU ASSEMBLY LH (FRONT VERTICAL MOTOR CIRCUIT)

Pre-procedure1

a.

Disconnect the L27 power seat tilt motor assembly LH (front vertical motor) connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(L27)Location & Routing

Click Connector(L27)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Power Seat Tilt Position Motor LH (Front Seat Adjuster Assembly LH)

L27-2 - L27-3 Front vertical switch on 4.8 to 5.1 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE POWER SEAT TILT MOTOR ASSEMBLY LH

NG

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY LH - POWER SEAT TILT MOTOR ASSEMBLY LH)
6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY LH - POWER SEAT TILT MOTOR ASSEMBLY LH)

Pre-procedure1

a.

Disconnect the L43 position control ECU assembly LH connector.


b.

Disconnect the L27 power seat tilt motor assembly LH (front vertical motor) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L43,L27)Location & Routing

Click Connector(L43)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Position Control ECU Assembly LH

Click Connector(L27)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Power Seat Tilt Position Motor LH (Front Seat Adjuster Assembly LH)

L43-10 (SSFV) - L27-2 Always Below 1 Ω
L43-10 (SSFV) or L27-2 - Body ground Always 10 kΩ or higher
L43-12 (SGND) - L27-3 Always Below 1 Ω
L43-12 (SGND) or L27-3 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE POSITION CONTROL ECU ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT POWER SEAT TILT MOTOR ASSEMBLY LH (FRONT VERTICAL MOTOR)

OK

8.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY LH - POWER SEAT TILT MOTOR ASSEMBLY LH)

NG

REPLACE POWER SEAT TILT MOTOR ASSEMBLY LH

8.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY LH - POWER SEAT TILT MOTOR ASSEMBLY LH)

Pre-procedure1

a.

Disconnect the L41 and L42 position control ECU assembly LH connectors.


b.

Disconnect the L27 power seat tilt motor assembly LH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L41,L27,L42)Location & Routing

Click Connector(L41)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Position Control ECU Assembly LH

Click Connector(L27)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Power Seat Tilt Position Motor LH (Front Seat Adjuster Assembly LH)

Click Connector(L42)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Position Control ECU Assembly LH

L41-7 (FRV+) - L27-1 Always Below 1 Ω
L41-7 (FRV+) or L27-1 - Body ground Always 10 kΩ or higher
L42-4 (FRV-) - L27-4 Always Below 1 Ω
L42-4 (FRV-) or L27-4 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE POSITION CONTROL ECU ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Driver Seat > Clear DTCs
50002 162

Result:
Proceed to
NEXT



NEXT

10.CHECK FOR DTC
10.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Driver Seat > Trouble Codes
50001 162

Result:
Result Proceed to
B2652 is not output A
B2652 is output B



A

B

11.PERFORM ACTIVE TEST USING GTS (FRONT VERTICAL OPERATION)
11.PERFORM ACTIVE TEST USING GTS (FRONT VERTICAL OPERATION)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Front Vertical Operation Seat front vertical operation OFF/Down/Up -
Body Electrical > Driver Seat > Active Test
Tester Display
Front Vertical Operation
50004 162 3
OK:

Front vertical motor operates normally.



Result:
Proceed to
OK
NG



OK

12.CHECK POSITION CONTROL ECU ASSEMBLY RH (FRONT VERTICAL MOTOR CIRCUIT)

NG

14.INSPECT POWER SEAT TILT MOTOR ASSEMBLY LH (FRONT VERTICAL MOTOR)
12.CHECK POSITION CONTROL ECU ASSEMBLY RH (FRONT VERTICAL MOTOR CIRCUIT)

Pre-procedure1

a.

Disconnect the L2 power seat tilt motor assembly RH (front vertical motor) connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(L2)Location & Routing

Click Connector(L2)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Power Seat Tilt Position Motor RH (Front Seat Adjuster Assembly RH)

L2-2 - L2-3 Front vertical switch on 4.8 to 5.1 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE POWER SEAT TILT MOTOR ASSEMBLY RH (FRONT VERTICAL MOTOR)

NG

13.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY RH - POWER SEAT TILT MOTOR ASSEMBLY RH [FRONT VERTICAL MOTOR])
13.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY RH - POWER SEAT TILT MOTOR ASSEMBLY RH [FRONT VERTICAL MOTOR])

Pre-procedure1

a.

Disconnect the L17 position control ECU assembly RH connector.


b.

Disconnect the L2 power seat tilt motor assembly RH (front vertical motor) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L17,L2)Location & Routing

Click Connector(L17)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Position Control ECU Assembly RH

Click Connector(L2)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Power Seat Tilt Position Motor RH (Front Seat Adjuster Assembly RH)

L17-10 (SSFV) - L2-2 Always Below 1 Ω
L17-10 (SSFV) or L2-2 - Body ground Always 10 kΩ or higher
L17-12 (SGND) - L2-3 Always Below 1 Ω
L17-12 (SGND) or L2-3 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE POSITION CONTROL ECU ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT POWER SEAT TILT MOTOR ASSEMBLY LH (FRONT VERTICAL MOTOR)

OK

15.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY RH - POWER SEAT TILT MOTOR ASSEMBLY RH [FRONT VERTICAL MOTOR])

NG

REPLACE POWER SEAT TILT MOTOR ASSEMBLY RH

15.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY RH - POWER SEAT TILT MOTOR ASSEMBLY RH [FRONT VERTICAL MOTOR])

Pre-procedure1

a.

Disconnect the L15 and L16 position control ECU assembly RH connectors.


b.

Disconnect the L2 power seat tilt motor assembly RH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L15,L2,L16)Location & Routing

Click Connector(L15)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Position Control ECU Assembly RH

Click Connector(L2)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Power Seat Tilt Position Motor RH (Front Seat Adjuster Assembly RH)

Click Connector(L16)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Position Control ECU Assembly RH

L15-7 (FRV+) - L2-1 Always Below 1 Ω
L15-7 (FRV+) or L2-1 - Body ground Always 10 kΩ or higher
L16-4 (FRV-) - L2-4 Always Below 1 Ω
L16-4 (FRV-) or L2-4 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE POSITION CONTROL ECU ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR