Home › Vehicle Interior › SEAT › CLIMATE CONTROL SEAT SYSTEM
RM37H0E _58 Vehicle Interior _095292 SEAT _0457026 CLIMATE CONTROL SEAT SYSTEM J

SEAT  CLIMATE CONTROL SEAT SYSTEM  Climate Control System does not Operate on Driver Side  


DESCRIPTION

The air conditioning amplifier assembly receives ventilation volume switch signals when the ignition switch is ON, and then transmits airflow amount signals to each seat climate blower.

WIRING DIAGRAM

for LHD:


C450696E04
0.635,1.198 2.115,1.677 1.479,0.479 10 false Air Conditioning Control Assembly 5.469,4.115 7.042,4.656 1.573,0.542 10 false Air Conditioning Amplifier Assembly 5.469,3.927 6,4.094 0.531,0.167 10 false D81 5.479,1.677 6.01,1.844 0.531,0.167 10 false 14 5.781,1.76 6.313,1.927 0.531,0.167 10 false LOUT 4.458,1.781 4.99,1.948 0.531,0.167 10 false SIGN 3.917,1.781 4.448,1.948 0.531,0.167 10 false IG 4.479,3.094 5.01,3.26 0.531,0.167 10 false GND 4.885,1.677 5.417,1.844 0.531,0.167 10 false 7 4.885,2.979 5.417,3.146 0.531,0.167 10 false 8 3.698,1.677 4.229,1.844 0.531,0.167 10 false 1 1.417,1.781 3.375,2.177 1.958,0.396 10 false from A/C Relay 3.917,2.469 4.448,2.635 0.531,0.167 10 false BFB- 3.917,2.771 4.448,2.938 0.531,0.167 10 false CTB 3.917,3.083 4.448,3.25 0.531,0.167 10 false BBS 3.688,2.375 4.219,2.542 0.531,0.167 10 false 4 3.698,2.688 4.229,2.854 0.531,0.167 10 false 5 3.698,2.979 4.229,3.146 0.531,0.167 10 false 6 1.875,2.469 2.406,2.635 0.531,0.167 10 false GND 2.01,2.76 2.542,2.927 0.531,0.167 10 false IG 1.813,3.083 2.344,3.25 0.531,0.167 10 false BFB+ 2.281,2.385 2.813,2.552 0.531,0.167 10 false 4 2.292,2.667 2.823,2.833 0.531,0.167 10 false 1 2.281,2.979 2.813,3.146 0.531,0.167 10 false 3 3.458,3.458 3.99,3.625 0.531,0.167 10 false L37 3.458,3.656 5.281,4.24 1.823,0.583 10 false Seat Cushion Climate Control Blower Assembly LH 1,3.5 1.573,3.677 0.573,0.177 10 false L53 1,3.677 2.604,4.271 1.604,0.594 10 false Seatback Climate Control Blower LH 0.813,4.354 2.656,4.604 1.844,0.25 10 false : LIN Communication Line 2.885,1.917 4.01,2.104 1.125,0.188 10 false A/C NO. 3


for RHD:


C450696E05
0.635,1.198 2.115,1.677 1.479,0.479 10 false Air Conditioning Control Assembly 5.469,4.115 7.042,4.656 1.573,0.542 10 false Air Conditioning Amplifier Assembly 5.469,3.927 6,4.094 0.531,0.167 10 false D81 5.479,1.677 6.01,1.844 0.531,0.167 10 false 13 5.781,1.76 6.313,1.927 0.531,0.167 10 false ROUT 4.458,1.781 4.99,1.948 0.531,0.167 10 false SIGN 3.917,1.781 4.448,1.948 0.531,0.167 10 false IG 4.479,3.094 5.01,3.26 0.531,0.167 10 false GND 4.885,1.677 5.417,1.844 0.531,0.167 10 false 7 4.885,2.979 5.417,3.146 0.531,0.167 10 false 8 3.698,1.677 4.229,1.844 0.531,0.167 10 false 1 1.417,1.781 3.375,2.177 1.958,0.396 10 false from A/C Relay 3.917,2.469 4.448,2.635 0.531,0.167 10 false BFB- 3.917,2.771 4.448,2.938 0.531,0.167 10 false CTB 3.917,3.083 4.448,3.25 0.531,0.167 10 false BBS 3.688,2.375 4.219,2.542 0.531,0.167 10 false 4 3.698,2.688 4.229,2.854 0.531,0.167 10 false 5 3.698,2.979 4.229,3.146 0.531,0.167 10 false 6 1.875,2.469 2.406,2.635 0.531,0.167 10 false GND 2.01,2.76 2.542,2.927 0.531,0.167 10 false IG 1.813,3.083 2.344,3.25 0.531,0.167 10 false BFB+ 2.281,2.385 2.813,2.552 0.531,0.167 10 false 4 2.292,2.667 2.823,2.833 0.531,0.167 10 false 1 2.281,2.979 2.813,3.146 0.531,0.167 10 false 3 3.448,3.406 3.979,3.573 0.531,0.167 10 false L12 3.438,3.583 5.26,4.167 1.823,0.583 10 false Seat Cushion Climate Control Blower Assembly RH 1,3.5 1.573,3.677 0.573,0.177 10 false L46 1,3.677 2.604,4.271 1.604,0.594 10 false Seatback Climate Control Blower RH 0.813,4.354 2.656,4.604 1.844,0.25 10 false : LIN Communication Line 2.885,1.917 4.01,2.104 1.125,0.188 10 false A/C NO. 2


CAUTION / NOTICE / HINT

NOTICE:
·

If the auxiliary battery voltage is low, the climate control seat system may not operate. When "High Power Consumption Partial Limit on AC/Heater Operation" is displayed on the multi-information display in the combination meter assembly, inspect the auxiliary battery, referring to On-vehicle Inspection for the charging system.

Click herePower Source / Network>BATTERY / CHARGING>CHARGING SYSTEM>ON-VEHICLE INSPECTION

·

If the climate control seat system is operated when the auxiliary battery voltage is low, due to the electrical load limit control that gives voltage supply priority to the power steering system, the climate control seat system may not operate. In this case, check the vehicle control history of the power steering system and check that "Battery Voltage Drop: X208F" is not stored before proceeding with troubleshooting.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>VEHICLE CONTROL HISTORY

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.PERFORM ACTIVE TEST USING GTS (SEAT BLOWER)

B

10.PERFORM ACTIVE TEST USING GTS (SEAT BLOWER)
2.PERFORM ACTIVE TEST USING GTS (SEAT BLOWER)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Front Left Seat Blower LH side seat blower operation OFF/ON -
Body Electrical > Air Conditioner > Active Test
Tester Display
Front Left Seat Blower
50004 121 121

Result:
Result Proceed to
Both seat cushion seat blower and seatback seat blower operate A
Only seat cushion seat blower does not operate B
Only seatback seat blower does not operate C
Both seat cushion seat blower and seatback seat blower do not operate D



A

3.CHECK CLIMATE CONTROL SEAT OPERATION

B

REPLACE SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY LH

C

4.CHECK HARNESS AND CONNECTOR (SEATBACK CLIMATE CONTROL BLOWER LH - SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY LH)

D

7.CHECK HARNESS AND CONNECTOR (SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY LH - BATTERY AND BODY GROUND)
3.CHECK CLIMATE CONTROL SEAT OPERATION
a.

Check the climate control seat operation.

Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>OPERATION CHECK

OK:

The climate control seat operates normally.



Result:
Resutk Proceed to
Does not operate normally with operation of either the multi-display or seat blower switch A
Does not operate normally with operation of the multi-display B
Does not operate normally with operation of the seat blower switch C



A

B

C

4.CHECK HARNESS AND CONNECTOR (SEATBACK CLIMATE CONTROL BLOWER LH - SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY LH)
a.

Disconnect the L53 seatback climate control blower LH connector.


b.

Disconnect the L37 seat cushion climate control blower assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L53,L37)Location & Routing

Click Connector(L53)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Seat Back Climate Control Blower LH

Click Connector(L37)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Seat Cushion Climate Control Blower Assembly LH

L53-4 (GND) - L37-4 (BFB-) Always Below 1 Ω
L53-4 (GND) or L37-4 (BFB-) - Other terminals and body ground Always 10 kΩ or higher
L53-1 (IG) - L37-5 (CTB) Always Below 1 Ω
L53-1 (IG) or L37-5 (CTB) - Other terminals and body ground Always 10 kΩ or higher
L53-3 (BFB+) - L37-6 (BBS) Always Below 1 Ω
L53-3 (BFB+) or L37-6 (BBS) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE SEATBACK CLIMATE CONTROL BLOWER LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE SEATBACK CLIMATE CONTROL BLOWER LH
a.

Replace the seatback climate control blower LH with a new or known good one.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

6.CHECK CLIMATE CONTROL SEAT OPERATION
6.CHECK CLIMATE CONTROL SEAT OPERATION
a.

Check the climate control seat operation.

Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>OPERATION CHECK

OK:

The climate control seat operates normally.



Result:
Proceed to
OK
NG



OK

END (SEATBACK CLIMATE CONTROL BLOWER LH WAS DEFECTIVE)

NG

REPLACE SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY LH

7.CHECK HARNESS AND CONNECTOR (SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY LH - BATTERY AND BODY GROUND)
a.

Disconnect the L37 seat cushion climate control blower assembly LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(L37)Location & Routing

Click Connector(L37)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Seat Cushion Climate Control Blower Assembly LH

L37-1 (IG) - Body ground Ignition switch ON 11 to 14 V
L37-1 (IG) - Body ground Ignition switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L37)Location & Routing

Click Connector(L37)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Seat Cushion Climate Control Blower Assembly LH

L37-8 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY LH - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY LH - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the L37 seat cushion climate control blower assembly LH connector.


b.

Disconnect the D81 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L37,D81)Location & Routing

Click Connector(L37)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Seat Cushion Climate Control Blower Assembly LH

Click Connector(D81)Instrument Panel>Instrument Panel Wire>Air Conditioning Amplifier Assembly

L37-7 (SIGN) - D81-14 (LOUT) Always Below 1 Ω
L37-7 (SIGN) or D81-14 (LOUT) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.
E409337C13
1.75,0.083 2.125,0.302 0.375,0.219 1.354,1.469 1.49,1.469 1.49,1.469 1.688,0.76 true 1.813,0.115 2.083,0.292 0.271,0.177 10 false D81 0.438,2.854 0.802,3.042 0.365,0.188 10 false GND 0.969,1.396 1.417,1.573 0.448,0.177 10 false LOUT 0.135,0.083 0.313,0.25 0.177,0.167 10 false *a
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Check for pulses according to the value(s) in the table below.

Measurement Condition
Item Content
Tester Connection D81-14 (LOUT) - Body ground
Tool Setting 1 V/DIV., 1 ms/DIV.
Vehicle Condition
·

Ignition switch ON

·

LH side refreshing seat switch (seat blower switch) operate



OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

REPLACE SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY LH

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

10.PERFORM ACTIVE TEST USING GTS (SEAT BLOWER)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Front Right Seat Blower RH side seat blower operation OFF/ON -
Body Electrical > Air Conditioner > Active Test
Tester Display
Front Right Seat Blower
50004 121 120

Result:
Result Proceed to
Both seat cushion seat blower and seatback seat blower operate A
Only seat cushion seat blower does not operate B
Only seatback seat blower does not operate C
Both seat cushion seat blower and seatback seat blower do not operate D



A

11.CHECK CLIMATE CONTROL SEAT OPERATION

B

REPLACE SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY RH

C

12.CHECK HARNESS AND CONNECTOR (SEATBACK CLIMATE CONTROL BLOWER RH - SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY RH)

D

15.CHECK HARNESS AND CONNECTOR (SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY RH - BATTERY AND BODY GROUND)
11.CHECK CLIMATE CONTROL SEAT OPERATION
a.

Check the climate control seat operation.

Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>OPERATION CHECK

OK:

The climate control seat operates normally.



Result:
Result Proceed to
Does not operate normally with operation of either the multi-display or seat blower switch A
Does not operate normally with operation of the multi-display B
Does not operate normally with operation of the seat blower switch C



A

B

C

12.CHECK HARNESS AND CONNECTOR (SEATBACK CLIMATE CONTROL BLOWER RH - SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY RH)
a.

Disconnect the L46 seatback climate control blower RH connector.


b.

Disconnect the L12 seat cushion climate control blower assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L46,L12)Location & Routing

Click Connector(L46)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Seat Back Climate Control Blower RH

Click Connector(L12)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Seat Cushion Climate Control Blower Assembly RH

L46-4 (GND) - L12-4 (BFB-) Always Below 1 Ω
L46-4 (GND) or L12-4 (BFB-) - Other terminals and body ground Always 10 kΩ or higher
L46-1 (IG) - L12-5 (CTB) Always Below 1 Ω
L46-1 (IG) or L12-5 (CTB) - Other terminals and body ground Always 10 kΩ or higher
L46-3 (BFB+) - L12-6 (BBS) Always Below 1 Ω
L46-3 (BFB+) or L12-6 (BBS) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.REPLACE SEATBACK CLIMATE CONTROL BLOWER RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.REPLACE SEATBACK CLIMATE CONTROL BLOWER RH
a.

Replace the seatback climate control blower RH with a new or known good one.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

14.CHECK CLIMATE CONTROL SEAT OPERATION
14.CHECK CLIMATE CONTROL SEAT OPERATION
a.

Check the climate control seat operation.

Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>OPERATION CHECK

OK:

The climate control seat operates normally.



Result:
Proceed to
OK
NG



OK

END (SEATBACK CLIMATE CONTROL BLOWER RH WAS DEFECTIVE)

NG

REPLACE SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY RH

15.CHECK HARNESS AND CONNECTOR (SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY RH - BATTERY AND BODY GROUND)
a.
B416369C96
1.542,0.302 2.042,0.552 0.5,0.25 0.833,0.75 1.083,0.75 1.083,0.75 1.479,1.25 true 2.115,1.521 2.302,1.948 2.302,1.948 2.438,1.948 true 0.24,0.135 0.552,0.333 0.313,0.198 10 false *a 1.677,0.354 1.99,0.552 0.313,0.198 10 false L12 0.646,0.677 0.979,0.854 0.333,0.177 10 false IG 2.479,1.885 2.823,2.063 0.344,0.177 10 false GND
*a Front view of wire harness connector
(to Seat Cushion Climate Control Blower Assembly RH)


Disconnect the seat cushion climate control blower assembly RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(L12)Location & Routing

Click Connector(L12)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Seat Cushion Climate Control Blower Assembly RH

L12-1 (IG) - Body ground Ignition switch ON 11 to 14 V
L12-1 (IG) - Body ground Ignition switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L12)Location & Routing

Click Connector(L12)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Seat Cushion Climate Control Blower Assembly RH

L12-8 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY RH - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY RH - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the L12 seat cushion climate control blower assembly RH connector.


b.

Disconnect the D81 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L12,D81)Location & Routing

Click Connector(L12)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Seat Cushion Climate Control Blower Assembly RH

Click Connector(D81)Instrument Panel>Instrument Panel Wire>Air Conditioning Amplifier Assembly

L12-7 (SIGN) - D81-13 (ROUT) Always Below 1 Ω
L12-7 (SIGN) or D81-13 (ROUT) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

17.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.
E409337C14
1.75,0.083 2.125,0.302 0.375,0.219 1.438,1.469 1.573,1.469 1.573,1.469 1.771,0.76 true 1.802,0.115 2.177,0.344 0.375,0.229 10 false D81 0.438,2.854 0.802,3.042 0.365,0.188 10 false GND 1.031,1.396 1.479,1.573 0.448,0.177 10 false ROUT 0.115,0.073 0.281,0.24 0.167,0.167 10 false *a
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Check for pulses according to the value(s) in the table below.

Measurement Condition
Item Content
Tester Connection D81-13 (ROUT) - Body ground
Tool Setting 1 V/DIV., 1 ms/DIV.
Vehicle Condition
·

Ignition switch ON

·

RH side refreshing seat switch (seat blower switch) operate



OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

REPLACE SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY RH

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY