| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | POSITION CONTROL ECU ASSEMBLY LH | 89710D | - | - | - |
| 2 | REMOVE FRONT SEAT INNER BELT ASSEMBLY LH | 73240 | - | - | - |
| 3 | REMOVE FRONT SEAT INNER BELT ASSEMBLY RH | 73230 | - | - | - |
| *A | for Driver Side | *B | for Front Passenger Side |
| *C | w/ Memory | - | - |
| *A | for Driver Side | *B | for Front Passenger Side |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 11 | NO. 2 LOWER SEAT TRACK SPACER | 72136A | - | - | - |
| 12 | NO. 1 LOWER SEAT TRACK SPACER | 72136 | - | - | - |
| 13 | FRONT POWER SEAT SWITCH LH | 84922C | - | - | - |
| 14 | FRONT POWER SEAT SWITCH RH | 84922B | - | - | - |
| *A | for Front Passenger Side | *B | for Driver Side |
| *1 | SEAT ADJUSTER SHIELD CLAMP BRACKET LH | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 15 | FRONT SEATBACK ASSEMBLY LH | - | ( )
|
- | - |
| 16 | FRONT SEAT CUSHION BRACKET LH | 79122 | - | - | - |
| 17 | NO. 3 INTERIOR ILLUMINATION LIGHT ASSEMBLY | 81080W | ( )
|
- | - |
| *A | w/ Foot light | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 18 | FRONT SEAT HEADREST SUPPORT | 71931 | ( )
|
- | - |
| 19 | SEPARATE TYPE FRONT SEATBACK COVER WITH PAD LH | - | - | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 20 | SEPARATE TYPE FRONT SEATBACK COVER LH | 71074S | ( )
|
- | - |
| 21 | FRONT SEATBACK HEATER ASSEMBLY LH | 87510N | ( )
|
- | - |
| *A | w/ Seat Heater System | - | - |
| *1 | SEPARATE TYPE FRONT SEATBACK PAD LH | - | - |
| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 22 | FRONT SEAT AIRBAG ASSEMBLY LH | 73920A | ( )
|
- | - |
| 23 | FRONT NO. 2 SEAT WIRE LH | 8219B | - | - | - |
| ● | Non-reusable part | - | - |
| *A | for Driver Side | *B | for Front Passenger Side |
| *C | w/ Climate Control Seat System | *D | w/o Climate Control Seat System |
| *1 | FRONT SEATBACK FRAME SUB-ASSEMBLY LH | - | - |
| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 31 | SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD LH | - | - | - | - |
| 32 | CONNECTOR HOLDER | 82667D | ( )
|
- | - |
| *A | for Front Passenger Side | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 33 | SEPARATE TYPE FRONT SEAT CUSHION COVER LH | 71072S | ( )
|
- | - |
| 34 | FRONT SEAT CUSHION HEATER ASSEMBLY LH | 87510L | ( )
|
- | - |
| *A | w/ Seat Heater System | - | - |
| *1 | SEPARATE TYPE FRONT SEAT CUSHION PAD LH | - | - |
| ● | Non-reusable part | - | - |
| *A | for Driver Side | *B | for Front Passenger Side |
| *C | w/ Climate Control Seat System | - | - |
| *A | for Driver Side | *B | w/ Seat Heater System |
| *1 | FRONT SEAT ADJUSTER ASSEMBLY LH | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 51 | POWER SEAT LIFTER MOTOR ASSEMBLY LH | 85822C | - | - | - |
| 52 | POWER SEAT TILT MOTOR ASSEMBLY LH | 85822B | - | - | - |
| *A | for Driver Side | - | - |
| *1 | FRONT SEAT VERTICAL HOUSING SUB-ASSEMBLY LH | *2 | VERTICAL ADJUSTER SPACER |
| *3 | FRONT SEAT ADJUSTER PLATE | - | - |
Wear protective gloves. Sharp areas on the parts may injure your hands.
There is risk of injury.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The following procedure is for the LH side.
89710D
1.REMOVE POSITION CONTROL ECU ASSEMBLY LH (w/ Memory)
73240
2.REMOVE FRONT SEAT INNER BELT ASSEMBLY LH (for Driver Side)
73230
3.REMOVE FRONT SEAT INNER BELT ASSEMBLY RH (for Front Passenger Side)
71868N
4.REMOVE FRONT SEAT FRONT CUSHION SHIELD LH
|
Place Hands Here |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) | - | - |
Remove the clip.
Place your hands at the position shown in the illustration and pull in the removal direction (1) to detach the guide.
Using a thin-bladed screwdriver, detach the claw.
Tape the thin-bladed screwdriver tip before use.
Place your hands at the position shown in the illustration and pull in the removal direction (1) to detach the guide and remove the front seat front cushion shield LH.
71812D
5.REMOVE FRONT SEAT CUSHION SHIELD LH (for Driver Side)
|
Place Hands Here |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
|
Remove in this Direction (3) |
Using moulding remover A, detach the claw and guide.
Place your hands at the position shown in the illustration and pull in the removal direction (1) to detach the claw.
Using a thin-bladed screwdriver, detach the claw.
Tape the thin-bladed screwdriver tip before use.
Place your hands at the position shown in the illustration and pull in the removal direction (3) to detach the guide.
Disconnect the connector and remove the front seat cushion shield LH.
71811D
6.REMOVE FRONT SEAT CUSHION SHIELD RH (for Front Passenger Side)
|
Place Hands Here |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
|
Remove in this Direction (3) |
Using moulding remover A, detach the claw and guide.
Place your hands at the position shown in the illustration and pull in the removal direction (1) to detach the claw.
Using a thin-bladed screwdriver, detach the claw.
Tape the thin-bladed screwdriver tip before use.
Place your hands at the position shown in the illustration and pull in the removal direction (3) to detach the guide.
Disconnect the connector and detach the clamp to remove the front seat cushion shield RH.
84921R
7.REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB
|
Remove in this Direction | - | - |
Using moulding remover A, detach the claw and remove the slide and vertical power seat switch knob.
84921Q
8.REMOVE RECLINING POWER SEAT SWITCH KNOB
|
Remove in this Direction | - | - |
Using moulding remover A, detach the claw and remove the reclining power seat switch knob.
71862
9.REMOVE FRONT INNER SEAT CUSHION SHIELD LH (for Driver Side)
|
Remove in this Direction |
|
Open in this Direction |
Using moulding remover A, detach the claw and guide.
Using a thin-bladed screwdriver, detach the claw.
Tape the thin-bladed screwdriver tip before use.
Open the front inner seat cushion shield LH as shown in the illustration and using a thin-bladed screwdriver, detach the claw and remove the front inner seat cushion shield LH.
Tape the thin-bladed screwdriver tip before use.
71861
10.REMOVE FRONT INNER SEAT CUSHION SHIELD RH (for Front Passenger Side)
|
Place Hands Here |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) | - | - |
Using moulding remover A, detach the claw and guide.
Using a thin-bladed screwdriver, detach the claw.
Tape the thin-bladed screwdriver tip before use.
Place your hands at the position shown in the illustration and pull in the removal direction (2) to detach the claw and remove the front inner seat cushion shield RH.
72136A
11.REMOVE NO. 2 LOWER SEAT TRACK SPACER (for Driver Side)
72136
12.REMOVE NO. 1 LOWER SEAT TRACK SPACER (for Front Passenger Side)
Use the same procedure described for the No. 2 lower seat track spacer.
84922C
13.REMOVE FRONT POWER SEAT SWITCH LH (for Driver Side)
84922B
14.REMOVE FRONT POWER SEAT SWITCH RH (for Front Passenger Side)
15.REMOVE FRONT SEATBACK ASSEMBLY LH
| *A | w/ Foot light | - | - |
|
Fastener | - | - |
Disconnect the band from the hook.
w/ Foot light:
1. Detach the fastener.
2. Disconnect the connector.
3. Detach the clamp.
Detach the claw and clamp.
Disconnect the connector and detach the clamp.
Detach the hook.
Remove the 4 bolts.
Using a screwdriver, detach the guide and remove the front seatback assembly.
Tape the screwdriver tip before use.
79122
16.REMOVE FRONT SEAT CUSHION BRACKET LH (w/ Foot light)
|
Remove in this Direction | - | - |
81080W
17.REMOVE NO. 3 INTERIOR ILLUMINATION LIGHT ASSEMBLY (w/ Foot light)
Using a thin-bladed screwdriver, detach the claw and remove the No. 3 interior illumination light assembly.
Tape the thin-bladed screwdriver tip before use.
71931
18.REMOVE FRONT SEAT HEADREST SUPPORT
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Detach the hook.
Pull out the fastener as shown in the illustration.
Open the 2 fasteners.
Detach the clamp.
Detach the claw and remove the 2 front seat headrest supports.
19.REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD LH
|
Remove in this Direction | - | - |
71074S
20.REMOVE SEPARATE TYPE FRONT SEATBACK COVER LH
|
|
Using a thin-bladed screwdriver, detach the claw to remove the separate type front seatback cover LH from the separate type front seatback pad LH as shown in the illustration.
Tape the thin-bladed screwdriver tip before use.
87510N
21.REMOVE FRONT SEATBACK HEATER ASSEMBLY LH (w/ Seat Heater System)
8219B
23.REMOVE FRONT NO. 2 SEAT WIRE LH
The illustrations are representative examples, and details may differ.
| *A | for Driver Side | *B | for Front Passenger Side |
72750D
25.REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY RH (for Front Passenger Side, w/ Climate Control Seat System)
71053S
26.REMOVE FRONT SEATBACK SPRING SUB-ASSEMBLY RH (for Front Passenger Side, w/o Climate Control Seat System)
79977A
27.REMOVE SEATBACK FELT
|
Remove in this Direction | - | - |
85867
28.REMOVE SEATBACK CLIMATE CONTROL BLOWER RH (w/ Climate Control Seat System)
71587
29.REMOVE FRONT SEATBACK EDGE PROTECTOR
Using a thin-bladed screwdriver, detach the claw and remove the 2 front seatback edge protectors.
Tape the thin-bladed screwdriver tip before use.
71759B
30.REMOVE FRONT SEATBACK HOOK
Using a thin-bladed screwdriver, detach the claw and remove the 2 front seatback hooks.
Tape the thin-bladed screwdriver tip before use.
31.REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD LH
| *A | for Driver Side | *B | for Front Passenger Side |
82667D
32.REMOVE CONNECTOR HOLDER (for Front Passenger Side)
Using a thin-bladed screwdriver, detach the claw and remove the connector holder.
Tape the thin-bladed screwdriver tip before use.
71072S
33.REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER LH
|
|
| *a | Band | - | - |
|
Remove in this Direction | - | - |
Detach the band.
Using a thin-bladed screwdriver, detach the claw to remove the separate type front seat cushion cover LH from the separate type front seat cushion pad LH as shown in the illustration.
Tape the thin-bladed screwdriver tip before use.
85860B
35.REMOVE SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY LH (w/ Climate Control Seat System)
85860A
36.REMOVE SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY RH (w/ Climate Control Seat System)
Use the same procedure described for the LH side.
71875G
37.REMOVE LH SEAT RECLINING ADJUSTER INSIDE COVER LH (for Driver Side)
|
Remove in this Direction | - | - |
Using a thin-bladed screwdriver, detach the claw.
Tape the thin-bladed screwdriver tip before use.
Detach the claw and hook to remove the LH seat reclining adjuster inside cover LH as shown in the illustration.
71875F
38.REMOVE RH SEAT RECLINING ADJUSTER INSIDE COVER LH (for Front Passenger Side)
|
Remove in this Direction | - | - |
71876G
39.REMOVE LH SEAT RECLINING ADJUSTER INSIDE COVER RH (for Driver Side)
|
Remove in this Direction | - | - |
71876F
40.REMOVE RH SEAT RECLINING ADJUSTER INSIDE COVER RH (for Front Passenger Side)
|
Remove in this Direction | - | - |
Detach the clamp.
Using a thin-bladed screwdriver, detach the claw.
Tape the thin-bladed screwdriver tip before use.
Detach the claw and hook to remove the RH seat reclining adjuster inside cover RH as shown in the illustration.
71874
41.REMOVE FRONT SEAT LOWER CUSHION SHIELD LH (for Driver Side)
| *a | Hook | *b | Guide |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Pull in the removal direction (1) shown in the illustration to detach the hook.
Using a thin-bladed screwdriver, detach the claw.
Tape the thin-bladed screwdriver tip before use.
Slide in the removal direction (2) shown in the illustration to detach guide and remove the front seat lower cushion shield LH.
71873U
42.REMOVE FRONT SEAT LOWER CUSHION SHIELD RH (for Driver Side)
| *a | Hook | *b | Guide |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Pull in the removal direction (1) shown in the illustration to detach the hook.
Using a thin-bladed screwdriver, detach the claw.
Tape the thin-bladed screwdriver tip before use.
Slide in the removal direction (2) shown in the illustration to detach guide and remove the front seat lower cushion shield RH.
7181B
43.REMOVE FRONT SEAT CUSHION WIRE HARNESS HOLDER LH (for Driver Side)
The illustrations are representative examples, and details may differ.
|
|
|
Remove in this Direction | - | - |
7181A
44.REMOVE FRONT SEAT CUSHION WIRE HARNESS HOLDER RH (for Front Passenger Side)
The illustrations are representative examples, and details may differ.
|
|
87501B
45.REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System)
| *A | for Driver Side | *B | for Front Passenger Side |
|
Remove in this Direction | - | - |
82192
46.REMOVE FRONT SEAT WIRE LH
The illustrations are representative examples, and details may differ.
| *A | for Driver Side | *B | for Front Passenger Side |
71873B
47.REMOVE FRONT SEAT NO. 1 CUSHION SHIELD (for Driver Side)
|
Remove in this Direction | - | - |
Using a thin-bladed screwdriver, detach the claw.
Tape the thin-bladed screwdriver tip before use.
Pull in the removal direction shown in the illustration to detach the guide and remove the front No. 1 seat cushion shield.
71052A
48.REMOVE FRONT SEAT CUSHION SPRING SUB-ASSEMBLY LH
| *a | Hook A | *b | Hook B |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Pull in the removal direction (1) shown in the illustration to detach hook A.
Pull in the removal direction (2) shown in the illustration to detach hook B and remove the front seat cushion spring sub-assembly LH.
72265D
49.REMOVE UPPER SEAT TRACK RAIL COVER
|
|
| *a | Matchmark | - | - |
Place a matchmark on the front seat adjuster assembly LH.
| *a | Terminal of the Slide Motor | - | - |
|
Remove in this Direction | - | - |
w/ Memory:
1. Connect the No. 4 terminal of the slide motor to the positive (+) auxiliary battery terminal, and the No. 1 terminal to the negative (-) auxiliary battery terminal and then move the front seat adjuster assembly LH to the frontmost position.
After performing this procedure, initialize the seat ECU (position control ECU assembly).
w/o Memory:
1. Connect the No. 2 terminal of the slide motor to the positive (+) auxiliary battery terminal, and the No. 1 terminal to the negative (-) auxiliary battery terminal and then move the front seat adjuster assembly LH to the frontmost position.
Using a thin-bladed screwdriver, detach the claw and remove the upper seat track rail cover.
Tape the thin-bladed screwdriver tip before use.
72125A
50.REMOVE REAR UPPER SEAT TRACK COVER
|
|
| *a | Terminal of the Slide Motor | - | - |
|
Remove in this Direction | - | - |
w/ Memory:
1. Connect the No. 1 terminal of the slide motor to the positive (+) auxiliary battery terminal, and the No. 4 terminal to the negative (-) auxiliary battery terminal and then move the front seat adjuster assembly LH to the rearmost position.
After performing this procedure, initialize the seat ECU (position control ECU assembly).
w/o Memory:
1. Connect the No. 1 terminal of the slide motor to the positive (+) auxiliary battery terminal, and the No. 2 terminal to the negative (-) auxiliary battery terminal and then move the front seat adjuster assembly LH to the rearmost position.
Using a thin-bladed screwdriver, detach the claw and remove the rear upper seat track cover.
Tape the thin-bladed screwdriver tip before use.
85822C
51.REMOVE POWER SEAT LIFTER MOTOR ASSEMBLY LH (for Driver Side)
85822B
52.REMOVE POWER SEAT TILT MOTOR ASSEMBLY LH (for Driver Side)