The air conditioning amplifier assembly receives ventilation volume switch signals when the ignition switch is ON, and then transmits airflow amount signals to each seat climate blower.
for LHD:
for RHD:
If the auxiliary battery voltage is low, the climate control seat system may not operate. When "High Power Consumption Partial Limit on AC/Heater Operation" is displayed on the multi-information display in the combination meter assembly, inspect the auxiliary battery, referring to On-vehicle Inspection for the charging system.
Click herePower Source / Network>BATTERY / CHARGING>CHARGING SYSTEM>ON-VEHICLE INSPECTION
If the climate control seat system is operated when the auxiliary battery voltage is low, due to the electrical load limit control that gives voltage supply priority to the power steering system, the climate control seat system may not operate. In this case, check the vehicle control history of the power steering system and check that "Battery Voltage Drop: X208F" is not stored before proceeding with troubleshooting.
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>VEHICLE CONTROL HISTORY
Inspect the fuses for circuits related to this system before performing the following procedure.
Check the vehicle type.
| Result | Proceed to |
|---|---|
| for LHD | A |
| for RHD | B |
A
B
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Front Right Seat Blower | RH side seat blower operation | OFF/ON | - |
| Tester Display |
|---|
| Front Right Seat Blower |
| Result | Proceed to |
|---|---|
| Both seat cushion seat blower and seatback seat blower operate | A |
| Only seat cushion seat blower does not operate | B |
| Only seatback seat blower does not operate | C |
| Both seat cushion seat blower and seatback seat blower do not operate | D |
A
B
C
D
Check the climate control seat operation.
Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>OPERATION CHECK
The climate control seat operates normally.
| Result | Proceed to |
|---|---|
| Does not operate normally with operation of either the multi-display or seat blower switch | A |
| Does not operate normally with operation of the multi-display | B |
| Does not operate normally with operation of the seat blower switch | C |
A
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL (for LHD Front)>REMOVAL
B
C
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL (for LHD Front)>REMOVAL
Disconnect the L46 seatback climate control blower RH connector.
Disconnect the L12 seat cushion climate control blower assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(L46,L12)Location & Routingewd_type=routing;type=c,c;code=L46,L12 Click Connector(L46)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Seat Back Climate Control Blower RHewd_type=component;type=c;code=L46;pinno=4,1,3 Click Connector(L12)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Seat Cushion Climate Control Blower Assembly RHewd_type=component;type=c;code=L12;pinno=4,5,6 |
||
| L46-4 (GND) - L12-4 (BFB-) | Always | Below 1 Ω |
| L46-4 (GND) or L12-4 (BFB-) - Other terminals and body ground | Always | 10 kΩ or higher |
| L46-1 (IG) - L12-5 (CTB) | Always | Below 1 Ω |
| L46-1 (IG) or L12-5 (CTB) - Other terminals and body ground | Always | 10 kΩ or higher |
| L46-3 (BFB+) - L12-6 (BBS) | Always | Below 1 Ω |
| L46-3 (BFB+) or L12-6 (BBS) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the seatback climate control blower RH with a new or known good one.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>DISASSEMBLY
| Proceed to |
|---|
| NEXT |
NEXT
Check the climate control seat operation.
Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>OPERATION CHECK
The climate control seat operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the L12 seat cushion climate control blower assembly RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(L12)Location & Routingewd_type=routing;type=c;code=L12 Click Connector(L12)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Seat Cushion Climate Control Blower Assembly RHewd_type=component;type=c;code=L12;pinno=1 |
||
| L12-1 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| L12-1 (IG) - Body ground | Ignition switch off | Below 1 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(L12)Location & Routingewd_type=routing;type=c;code=L12 Click Connector(L12)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Seat Cushion Climate Control Blower Assembly RHewd_type=component;type=c;code=L12;pinno=8 |
||
| L12-8 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the L12 seat cushion climate control blower assembly RH connector.
Disconnect the D81 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(L12,D81)Location & Routingewd_type=routing;type=c,c;code=L12,D81 Click Connector(L12)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Seat Cushion Climate Control Blower Assembly RHewd_type=component;type=c;code=L12;pinno=7 Click Connector(D81)Instrument Panel>Instrument Panel Wire>Air Conditioning Amplifier Assemblyewd_type=component;type=c;code=D81;pinno=13 |
||
| L12-7 (SIGN) - D81-13 (ROUT) | Always | Below 1 Ω |
| L12-7 (SIGN) or D81-13 (ROUT) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Air Conditioning Amplifier Assembly) |
Check for pulses according to the value(s) in the table below.
| Item | Content |
|---|---|
| Tester Connection | G46-13 (ROUT) - Body ground |
| Tool Setting | 1 V/DIV., 1 ms/DIV. |
| Vehicle Condition | ·
Ignition switch ON ·
RH side refreshing seat switch (seat blower switch) operate |
Waveform is similar to that shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Front Left Seat Blower | LH side seat blower operation | OFF/ON | - |
| Tester Display |
|---|
| Front Left Seat Blower |
| Result | Proceed to |
|---|---|
| Both seat cushion seat blower and seatback seat blower operate | A |
| Only seat cushion seat blower does not operate | B |
| Only seatback seat blower does not operate | C |
| Both seat cushion seat blower and seatback seat blower do not operate | D |
A
B
C
D
Check the climate control seat operation.
Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>OPERATION CHECK
The climate control seat operates normally.
| Result | Proceed to |
|---|---|
| Does not operate normally with operation of either the multi-display or seat blower switch | A |
| Does not operate normally with operation of the multi-display | B |
| Does not operate normally with operation of the seat blower switch | C |
A
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL (for RHD Front)>REMOVAL
B
C
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL (for RHD Front)>REMOVAL
Disconnect the L53 seatback climate control blower LH connector.
Disconnect the L37 seat cushion climate control blower assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(L53,L37)Location & Routingewd_type=routing;type=c,c;code=L53,L37 Click Connector(L53)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Seat Back Climate Control Blower LHewd_type=component;type=c;code=L53;pinno=4,1,3 Click Connector(L37)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Seat Cushion Climate Control Blower Assembly LHewd_type=component;type=c;code=L37;pinno=4,5,6 |
||
| L53-4 (GND) - L37-4 (BFB-) | Always | Below 1 Ω |
| L53-4 (GND) or L37-4 (BFB-) - Other terminals and body ground | Always | 10 kΩ or higher |
| L53-1 (IG) - L37-5 (CTB) | Always | Below 1 Ω |
| L53-1 (IG) or L37-5 (CTB) - Other terminals and body ground | Always | 10 kΩ or higher |
| L53-3 (BFB+) - L37-6 (BBS) | Always | Below 1 Ω |
| L53-3 (BFB+) or L37-6 (BBS) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the seatback climate control blower LH with a new or known good one.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>DISASSEMBLY
| Proceed to |
|---|
| NEXT |
NEXT
Check the climate control seat operation.
Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>OPERATION CHECK
The climate control seat operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the L37 seat cushion climate control blower assembly LH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(L37)Location & Routingewd_type=routing;type=c;code=L37 Click Connector(L37)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Seat Cushion Climate Control Blower Assembly LHewd_type=component;type=c;code=L37;pinno=1 |
||
| L37-1 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| L37-1 (IG) - Body ground | Ignition switch off | Below 1 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(L37)Location & Routingewd_type=routing;type=c;code=L37 Click Connector(L37)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Seat Cushion Climate Control Blower Assembly LHewd_type=component;type=c;code=L37;pinno=8 |
||
| L37-8 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the L37 seat cushion climate control blower assembly LH connector.
Disconnect the D81 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(L37,D81)Location & Routingewd_type=routing;type=c,c;code=L37,D81 Click Connector(L37)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Seat Cushion Climate Control Blower Assembly LHewd_type=component;type=c;code=L37;pinno=7 Click Connector(D81)Instrument Panel>Instrument Panel Wire>Air Conditioning Amplifier Assemblyewd_type=component;type=c;code=D81;pinno=14 |
||
| L37-7 (SIGN) - D81-14 (LOUT) | Always | Below 1 Ω |
| L37-7 (SIGN) or D81-14 (LOUT) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Air Conditioning Amplifier Assembly) |
Check for pulses according to the value(s) in the table below.
| Item | Content |
|---|---|
| Tester Connection | D81-14 (LOUT) - Body ground |
| Tool Setting | 1 V/DIV., 1 ms/DIV. |
| Vehicle Condition | ·
Ignition switch ON ·
LH side refreshing seat switch (seat blower switch) operate |
Waveform is similar to that shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG