The air conditioning amplifier assembly receives ventilation volume switch signals when the ignition switch is ON, and then transmits airflow amount signals to each seat climate blower.
The climate control seat system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the climate control seat system after confirming that the communication system is functioning properly.
Click herePower Source / Network>BATTERY / CHARGING>CHARGING SYSTEM>ON-VEHICLE INSPECTION
If the battery voltage is low, the climate control seat system may not operate. When "High Power Consumption Partial Limit On AC/Heater Operation" is displayed on the multi-information display in the combination meter assembly, inspect the battery, referring to On-vehicle Inspection for the charging system.
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>VEHICLE CONTROL HISTORY
Inspect the fuses for circuits related to this system before performing the following procedure.
Check the climate control seat operation.
Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Rear Left Seat Blower | Rear seat LH side seat climate control operation | OFF/ON | - |
| Tester Display |
|---|
| Rear Left Seat Heater |
| Result | Proceed to |
|---|---|
| Seat blower operates normally | A |
| Seat blower dose not operate normally | B |
A
B
Temporarily replace the cooler control switch assembly with a new or known good one.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL (for Rear Side)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check the climate control seat operation again.
Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>OPERATION CHECK
The climate control seat operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the M2 rear seat cushion climate control blower assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(M2)Location & Routingewd_type=routing;type=c;code=M2 Click Connector(M2)Seat>No. 1 Rear Seat Wire / No. 2 Rear Seat Wire>Rear Seat Cushion Climate Control Blower Assembly LHewd_type=component;type=c;code=M2;pinno=8 |
||
| M2-8 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(M2)Location & Routingewd_type=routing;type=c;code=M2 Click Connector(M2)Seat>No. 1 Rear Seat Wire / No. 2 Rear Seat Wire>Rear Seat Cushion Climate Control Blower Assembly LHewd_type=component;type=c;code=M2;pinno=1 |
||
| M2-1 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V | |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the D79 air conditioning amplifier assembly connector.
Disconnect the M2 rear seat cushion climate control blower assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D79,M2)Location & Routingewd_type=routing;type=c,c;code=D79,M2 Click Connector(D79)Instrument Panel>Instrument Panel Wire>Air Conditioning Amplifier Assemblyewd_type=component;type=c;code=D79;pinno=22 Click Connector(M2)Seat>No. 1 Rear Seat Wire / No. 2 Rear Seat Wire>Rear Seat Cushion Climate Control Blower Assembly LHewd_type=component;type=c;code=M2;pinno=7 |
||
| D79-22 (SV2L) - M2-7 (SING) | Always | Below 1 Ω |
| D79-22 (SV2L) or M2-7 (SING) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Air Conditioning Amplifier Assembly) |
Check for pulses according to the value(s) in the table below.
| Item | Content |
|---|---|
| Tester Connection | D79-22 (SV2L) - Body ground |
| Tool Setting | 1 V/DIV., 1 ms/DIV. |
| Vehicle Condition | ·
Ignition switch ON ·
Rear right side refreshing seat switch (seat blower switch) on |
Waveform is similar to that shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL (for Rear Side)>REMOVAL
NG