Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › WATER PUMP WITH MOTOR
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0457185 WATER PUMP WITH MOTOR A

HYBRID / BATTERY CONTROL  WATER PUMP WITH MOTOR  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A478645N02
6.417,0.313 6.833,0.313 false 1.177,4.646 1.594,4.646 false 1.458,1.719 1.583,2 1.583,2 1.75,2 false 2.927,3.208 3.052,3.49 3.052,3.49 3.219,3.49 false 1.344,3.25 1.469,3.531 1.469,3.531 1.635,3.531 false 4.344,0.979 4.844,0.979 false 4.052,1.688 4.469,1.688 false 4.354,2.302 4.615,2.302 false 5.49,2.417 6,2.417 false 6.031,3.021 6.292,3.021 false 6.542,1.521 6.74,1.521 false 5.677,1.323 5.865,1.083 5.865,1.083 6.031,1.083 false 5.25,1.313 5.25,1.531 false 4.698,1.396 4.698,1.615 false 4.771,2.542 4.771,2.76 false 5.729,2.813 5.729,3.031 false 3.302,3.344 3.615,3.708 0.313,0.365 18 false 1 6.219,0.177 6.531,0.542 0.313,0.365 18 false 5 1.698,3.406 2.01,3.771 0.313,0.365 18 false 3 1.823,1.875 2.135,2.24 0.313,0.365 18 false 2 1.677,4.521 1.99,4.885 0.313,0.365 18 false 4 4.135,0.833 4.448,1.198 0.313,0.365 18 false 6 6.438,2.323 6.75,2.688 0.313,0.365 18 false 7 1.708,0.948 2.021,1.146 0.313,0.198 10 false x 6 1.469,2.656 1.781,2.854 0.313,0.198 10 false x 6 3.667,2.365 3.979,2.563 0.313,0.198 10 false x 6 4.708,2.823 5.021,3.021 0.313,0.198 10 false *5 5.635,3.083 5.948,3.281 0.313,0.198 10 false *5 4.625,1.646 4.938,1.844 0.313,0.198 10 false *5 5.167,1.583 5.479,1.781 0.313,0.198 10 false *5 6.792,1.438 7.104,1.635 0.313,0.198 10 false *4 4.677,2.219 4.99,2.417 0.313,0.198 10 false *1 6.344,2.969 6.656,3.167 0.313,0.198 10 false *3 6.094,1.01 6.406,1.208 0.313,0.198 10 false *2 3.875,1.615 4.188,1.813 0.313,0.198 10 false *1 4.896,0.344 5.208,0.542 0.313,0.198 10 false x 2 5.677,1.885 5.99,2.083 0.313,0.198 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 UPPER RADIATOR SUPPORT SEAL 53292A - - -
2 RADIATOR COVER PLATE 53291B - - -
3 LOWER RADIATOR AIR DEFLECTOR 53295 - - -
4 RADIATOR SUPPORT TO CROSSMEMBER BRACE SUB-ASSEMBLY RH 53209F - - -
5 DRAIN COOLANT (for Inverter) - - (Click here) -
6 EV RESERVE TANK ASSEMBLY G91H0D (Click here) - -
7 WATER WITH MOTOR PUMP ASSEMBLY G9040E (Click here) - -

*1 NO. 6 FC INVERTER COOLING HOSE *2 NO. 7 FC INVERTER COOLING HOSE
*3 NO. 15 FC INVERTER COOLING HOSE *4 CONNECTOR
*5 HOSE CLIP - -

PROCEDURE

Hide 53292A 1.REMOVE UPPER RADIATOR SUPPORT SEAL

Hide 53291B 2.REMOVE RADIATOR COVER PLATE

Hide 53295 3.REMOVE LOWER RADIATOR AIR DEFLECTOR

Hide 53209F 4.REMOVE RADIATOR SUPPORT TO CROSSMEMBER BRACE SUB-ASSEMBLY RH

Hide 5.DRAIN COOLANT (for Inverter)

Hide G91H0D 6.REMOVE EV RESERVE TANK ASSEMBLY

a.
A479911N01
0.542,0.115 0.823,0.469 0.281,0.354 18 true i 4.083,0.104 4.365,0.458 0.281,0.354 18 true ii 2.125,2.01 2.625,2.375 0.5,0.365 18 true iii, iv

i.

Slide the 2 hose clips and disconnect the No. 7 FC inverter cooling hose and No. 6 FC inverter cooling hose from the EV reserve tank assembly.

NOTICE:
·

During removal, make sure not to damage the port of the EV reserve tank assembly or the inner surface of the hose.

·

Perform the work by hand. Do not use tools.

·

Put pieces of cloth into the pipes and disconnected hoses or cover the pipes and hoses with plastic bags to prevent foreign matter from entering the inverter water pump assembly and cooling system.

·

Do not apply excessive force to the No. 7 FC inverter cooling hose and No. 6 FC inverter cooling hose.




ii.

After disconnecting the No. 6 FC inverter cooling hose and No. 7 FC inverter cooling hose, plug the coolant pipe and hose with hose plugs or wrap them with a plastic bag to prevent coolant from spilling onto surrounding parts or foreign matter from entering the coolant path.


iii.

Remove the 2 bolts.


iv.

Disconnect the grommet and remove the EV reserve tank assembly.



Hide G9040E 7.REMOVE WATER WITH MOTOR PUMP ASSEMBLY

a.
A478646N01
0.604,0.083 0.885,0.438 0.281,0.354 18 true i 4.052,0.073 4.333,0.427 0.281,0.354 18 true ii 0.615,2.021 0.896,2.375 0.281,0.354 18 true iii 4.094,2.042 4.375,2.396 0.281,0.354 18 true iv

i.

Disconnect the connector.

NOTICE:
To prevent the coolant from entering the water with motor pump assembly connector, perform the following procedure.
·

Wipe off any coolant around the water with motor pump assembly connector before disconnecting it.

·

Apply insulating tape to the connectors of the wire harness and water with motor pump assembly to prevent the entry of coolant.




ii.

Remove the 2 bolts.


iii.

Slide the 2 hose clips and disconnect the No. 6 FC inverter cooling hose and No. 15 FC inverter cooling hose from the water with motor pump assembly.

NOTICE:
·

During removal, make sure not to damage the port of the water with motor pump assembly or the inner surface of the hose.

·

Perform the work by hand. Do not use tools.

·

Put pieces of cloth into the pipes and disconnected hoses or cover the pipes and hoses with plastic bags to prevent foreign matter from entering the water with motor pump assembly and cooling system.

·

Do not apply excessive force to the No. 6 FC inverter cooling hose and No. 15 FC inverter cooling hose.




iv.

After disconnecting the No. 6 FC inverter cooling hose and No. 15 FC inverter cooling hose, plug the coolant pipe and hose with hose plugs or wrap them with a plastic bag to prevent coolant from spilling onto surrounding parts or foreign matter from entering the coolant path.