Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0459129 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C059400  Brake Booster Motor "A" Performance  


DESCRIPTION

The No. 1 skid control ECU (brake booster with master cylinder assembly) detects decreases in the accumulator pressure according to the data from the accumulator pressure sensor, and then starts and stops the pump motor by operating the motor relay.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
C059400 Brake Booster Motor "A" Performance The pump motor is operating continuously for 178 seconds or more.
·

Accumulator pressure sensor malfunction

·

Wire harness and connector

·

Brake booster pump assembly

·

Foreign matter enters SLA solenoid valve

·

No. 1 skid control ECU (brake booster with master cylinder assembly)


Brake Booster B Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)

WIRING DIAGRAM

C427348E10
4.938,1.792 5.552,1.99 0.615,0.198 10 false M+ 4.938,2.406 5.552,2.604 0.615,0.198 10 false M- 4.656,1.531 5.271,1.729 0.615,0.198 10 false 29 4.656,2.146 5.271,2.344 0.615,0.198 10 false 30 4.677,3.833 5.292,4.031 0.615,0.198 10 false A5 4.667,4.01 7.104,4.406 2.438,0.396 10 false No. 1 Skid Control ECU (Brake Booster with Master Cylinder Assembly) 0.167,2.781 0.781,2.979 0.615,0.198 10 false A39 0.156,2.958 2.156,3.365 2,0.406 10 false Brake Booster Pump Assembly 1.01,2.406 1.625,2.604 0.615,0.198 10 false GND1 1.521,1.51 2.135,1.708 0.615,0.198 10 false 1 1.083,1.781 1.698,1.979 0.615,0.198 10 false BM1 1.531,2.135 2.146,2.333 0.615,0.198 10 false 2 1.385,0.99 2.969,1.219 1.583,0.229 10 false from Auxiliary Battery 3.708,1.188 4.573,1.51 0.865,0.323 10 false ABS MTR 4.719,0.906 5.333,1.104 0.615,0.198 10 false 1 4.938,1.167 5.552,1.365 0.615,0.198 10 false MRI1 4.938,3.042 5.552,3.24 0.615,0.198 10 false MGND 5.5,1.854 6.458,2.25 0.958,0.396 10 false Semiconductor Relay 4.729,2.781 5.344,2.979 0.615,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the No. 1 skid control ECU (brake booster with master cylinder assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY



PROCEDURE

1.CHECK DTC
a.

Check the DTCs that are output.

Chassis > Brake Booster > Trouble Codes
50001 466

Result:
Result Proceed to
Only C059400 is output A
C059400 and other DTCs are output B



A

2.CHECK DTC

B

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

2.CHECK DTC
a.

Check the DTCs that are output.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

3.READ VALUE USING GTS (MOTOR RELAY)

B

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

3.READ VALUE USING GTS (MOTOR RELAY)
a.

Depress the brake pedal several times and check the operation status of the motor relay.

Chassis > Brake Booster > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ECB Motor Relay Motor relay operation request OFF / ON OFF: Relay off
ON: Relay on
ECB: Electronically Controlled Brake System
Chassis > Brake Booster > Data List
Tester Display
ECB Motor Relay
50003 466 96
HINT:

Depressing the brake pedal several times drops the accumulator pressure and operates the pump motor.



Result:
Result Proceed to
The status of motor relay in the Data List turns on and off after depressing the brake pedal several times. A
The status of motor relay in the Data List does not change even after depressing the brake pedal several times. B



A

4.INSPECT BRAKE BOOSTER PUMP ASSEMBLY

B

10.CHECK HARNESS AND CONNECTOR (MRI1 TERMINAL)
4.INSPECT BRAKE BOOSTER PUMP ASSEMBLY

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Inspect the brake booster pump assembly.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER PUMP>INSPECTION

OK:

The brake booster pump assembly is normal.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

5.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE BOOSTER PUMP ASSEMBLY)

NG

REPLACE BRAKE BOOSTER PUMP ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE BOOSTER PUMP ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A5 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A39,A5)Location & Routing

Click Connector(A39)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Booster Pump Assembly

Click Connector(A5)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Booster with Master Cylinder Assembly

A39-2 (GND1) or A5-30 (M-) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

6.READ VALUE USING GTS (MOTOR RELAY AND ACCUMULATOR PRESSURE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.READ VALUE USING GTS (MOTOR RELAY AND ACCUMULATOR PRESSURE)

Pre-procedure1

a.

Reconnect the A39 brake booster pump assembly connector.


b.

Reconnect the A5 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Disconnect the A2 brake pedal stroke sensor assembly connector.


d.

Depress the brake pedal several times to operate the pump motor, then wait until it stops.


Procedure1

a.

After the pump motor stops, wait for 30 seconds, then check the drop in the accumulator pressure sensor output value and the state of the pump motor.

Chassis > Brake Booster > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ECB Motor Relay Motor relay operation request OFF / ON OFF: Relay off
ON: Relay on
ECB: Electronically Controlled Brake System
Accumulator Pressure Accumulator pressure output value Min.: 0.00 MPa
Max.: 24.48 MPa
15.00 to 21.00 MPa (Pressure stable and pump motor stopped) When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator
Chassis > Brake Booster > Data List
Tester Display
ECB Motor Relay
Accumulator Pressure
50003 466 96,212
HINT:
·

This inspection checks whether an accumulator pressure sensor malfunction, internal brake booster with master cylinder assembly leak or prolonged operation due to detection of low pressure caused by accumulator deterioration, caused the DTC to be stored.

·

If the brake fluid level in the brake master cylinder reservoir assembly drops, an external brake fluid leak is suspected.



Result:
Result Proceed to
The drop in the accumulator pressure sensor output value is less than 2.50 MPa 30 seconds after the pump motor stops, and the pump motor does not operate within 30 seconds after the pump motor stops. A
The drop in the accumulator pressure sensor output value is 2.50 MPa or more 30 seconds after the pump motor stops, or the pump motor operates within 30 seconds after the pump motor stops. B



Post-procedure1

a.

None



A

7.CLEAR DTC

B

9.READ VALUE USING GTS (SERVO PRESSURE)
7.CLEAR DTC

Pre-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the A2 brake pedal stroke sensor assembly connector.


Procedure1

a.

Clear the DTCs.

Chassis > Brake Booster > Clear DTCs
50002 466
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

8.RECONFIRM DTC
8.RECONFIRM DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


Procedure1

a.

Check if the same DTC is output.

Chassis > Brake Booster > Trouble Codes
50001 466
Result:
Result Proceed to
C059400 is not output A
C059400 is output B



Post-procedure1

a.

None



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

9.READ VALUE USING GTS (SERVO PRESSURE)

Pre-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the A2 brake pedal stroke sensor assembly connector.


Procedure1

a.

Perform the Active Test and operate the linear solenoid (SLR) in the brake booster with master cylinder assembly.


b.

Check that the servo pressure output value does not increase when performing the Active Test.

Chassis > Brake Booster > Active Test
Tester Display Measurement Item Control Range Restrict Condition Diagnostic Note
ECB Solenoid (SLR) Linear solenoid reduction valve (SLR) Solenoid Start (Activate)
Solenoid SLR
(It is possible to set the current)
Vehicle condition:
·

Vehicle stopped

·

Check that park (P) is selected

·

Apply the parking brake


ECB: Electronically Controlled Brake System
Chassis > Brake Booster > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Servo Pressure Pressure value of servo Min.: 0.00 MPa
Max.: 24.48 MPa
Brake pedal released: 0.00 to 1.53 MPa Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal
Chassis > Brake Booster > Active Test
Active Test Display
ECB Solenoid (SLR)
Data List Display
Servo Pressure
50004 466 42 210
OK:

The servo pressure output value does not increase when performing the Active Test.


HINT:
·

If the servo pressure output value increases, an internal brake fluid leak in the brake booster with master cylinder assembly is suspected.

·

Perform the Active Test with the current set to maximum.



Result:
Result Proceed to
The servo pressure output value increases. A
The servo pressure output value does not increase. B



Post-procedure1

a.

None



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

REPLACE BRAKE BOOSTER PUMP ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (MRI1 TERMINAL)

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the A5 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A5)Location & Routing

Click Connector(A5)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Booster with Master Cylinder Assembly

A5-1 (MRI1) - Body ground Always 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

11.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE BOOSTER PUMP ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE BOOSTER PUMP ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A39 brake booster pump assembly connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A5,A39)Location & Routing

Click Connector(A5)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Booster with Master Cylinder Assembly

Click Connector(A39)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Booster Pump Assembly

A5-29 (M+) - A39-1 (BM1) Always Below 1 Ω
A5-29 (M+) or A39-1 (BM1) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR