Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0459129 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C136F00  Non-learning of the Braking System information.  


DESCRIPTION

The No. 1 skid control ECU (brake booster with master cylinder assembly) stores identification information sent from other ECUs when the vehicle is shipped from the factory and changes the control constant for each system (ABS, VSC, TRC, etc.) based on the identification information.

NOTICE:

DTC C136F00 is output when an incorrect ECU is installed. If initialization is performed and learning occurs with an incorrect ECU installed, operations and functions will differ from those stored when the vehicle was shipped from the factory. Therefore, make sure that learning occurs properly.


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
C136F00 Non-learning of the Braking System information. Either of the following is detected:
·

The drive system information sent from the EV control ECU does not match the information stored in the No. 1 skid control ECU (brake booster with master cylinder assembly).

·

No system information stored in the No. 1 skid control ECU (brake booster with master cylinder assembly).

·

The steering wheel judgment information sent from the main body ECU (multiplex network body ECU) does not match the information stored in the No. 1 skid control ECU (brake booster with master cylinder assembly).


·

Incorrect EV control ECU installed

·

No. 1 skid control ECU (brake booster with master cylinder assembly)

·

Incorrect main body ECU (multiplex network body ECU) installed


Brake Booster A Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)
HINT:

The DTC is cleared when the conditions return to normal.



C136F00 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition - - - -
Malfunction Status The drive system information sent from the EV control ECU does not match the information stored in the No. 1 skid control ECU (brake booster with master cylinder assembly) ○ - -
No system information stored in the No. 1 skid control ECU (brake booster with master cylinder assembly) - ○ -
The steering wheel judgment information sent from the main body ECU (multiplex network body ECU) does not match the information stored in the No. 1 skid control ECU (brake booster with master cylinder assembly) - - ○
Detection Time - -
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:

After replacing the No. 1 skid control ECU (brake booster with master cylinder assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY


PROCEDURE

1.CHECK PART NUMBER (EV CONTROL ECU)
a.

Check that the proper EV control ECU is installed.

OK:

Proper EV control ECU is installed.



Result:
Proceed to
OK
NG



OK

2.CHECK PART NUMBER (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)

NG

2.CHECK PART NUMBER (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)
a.

Check that the proper No. 1 skid control ECU (brake booster with master cylinder assembly) is installed.

OK:

Proper No. 1 skid control ECU (brake booster with master cylinder assembly) is installed.



Result:
Proceed to
OK
NG



OK

3.CHECK PART NUMBER (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

3.CHECK PART NUMBER (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Check that the proper main body ECU (multiplex network body ECU) is installed.

OK:

Proper main body ECU (multiplex network body ECU) is installed.



Result:
Proceed to
OK
NG



OK

4.CLEAR SYSTEM INFORMATION

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

4.CLEAR SYSTEM INFORMATION
a.

Clear system information.

HINT:

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY


Chassis > Brake/EPB > Utility
Tester Display
Reset Memory
50005 435 4560

Result:
Proceed to
NEXT



NEXT

5.SYSTEM INFORMATION MEMORIZATION
5.SYSTEM INFORMATION MEMORIZATION
a.

Perform system information memorization.

HINT:

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY


Chassis > Brake/EPB > Utility
Tester Display
Calibration
50005 435 4554
HINT:

After performing "Reset Memory" using the GTS to clear the memorized value of the No. 1 skid control ECU (brake booster with master cylinder assembly), DTC C136F00 will be stored until system information memorization is performed.



Result:
Proceed to
NEXT



NEXT

6.CLEAR DTC
6.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Chassis > Brake Booster > Clear DTCs
50002 466
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

7.RECONFIRM DTC
7.RECONFIRM DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


Procedure1

a.

Check if the same DTC is output.

Chassis > Brake Booster > Trouble Codes
50001 466
Result:
Result Proceed to
C136F00 is not output A
C136F00 is output B



Post-procedure1

a.

None



A

END

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY