Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0459129 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C126E15  Reservoir Level Switch Circuit Short to Battery or Open  


DESCRIPTION

If the No. 1 skid control ECU (brake booster with master cylinder assembly) detects that the brake fluid level is low or there is an open in the brake fluid level warning switch signal circuit, DTC C126E15 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
C126E15 Reservoir Level Switch Circuit Short to Battery or Open The brake fluid level warning switch (brake booster with master cylinder assembly) circuit is open for 2 seconds or more.
·

Open in brake fluid level warning switch (brake booster with master cylinder assembly)

·

Open in wire harness

·

Uneven brake disc rotor wear

·

Brake fluid leaks

·

Low brake fluid

·

No. 1 skid control ECU (brake booster with master cylinder assembly)


Brake Booster A Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)

CAUTION / NOTICE / HINT

NOTICE:

After replacing the No. 1 skid control ECU (brake booster with master cylinder assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY


PROCEDURE

1.CHECK BRAKE FLUID LEVEL
a.

Check that the brake fluid level is sufficient.

HINT:

If the fluid level is low, check for fluid leaks, and repair as necessary.


i.

Check for brake fluid leaks (connection between the brake booster pump assembly, brake master cylinder reservoir assembly (brake booster with master cylinder assembly), brake booster with master cylinder assembly, brake actuator assembly, and wheel cylinders).

If no leaks exist, add and adjust fluid using the GTS.

HINT:

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>ON-VEHICLE INSPECTION



ii.

Check the thickness of the brake pad lining.

for Front Brake: Click hereBrake>BRAKE (FRONT)>FRONT BRAKE>INSPECTION

for Rear Brake: Click hereBrake>BRAKE (REAR)>REAR BRAKE>INSPECTION

HINT:

If the thickness is less than the standard, replace the brake pads with new ones.




Result:
Proceed to
OK
NG



OK

2.CHECK FOR FLUID LEAK

NG

CHECK AND REPAIR BRAKE FLUID LEAKS OR ADD FLUID

2.CHECK FOR FLUID LEAK
a.

Check that there are no leaks from the connections between the brake booster pump assembly, brake actuator assembly and brake booster with master cylinder assembly.

HINT:

As a visual check is very difficult, perform the check with the following procedure.


i.

Bleed the air from the brake system.

HINT:

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>BLEEDING



ii.

Turn the ignition switch off.


iii.

Disconnect the A2 brake pedal stroke sensor assembly connector.


iv.

Depress the brake pedal several times to operate the pump motor, then wait until it stops.


v.

After the pump motor stops, wait for 30 seconds, then check the drop in the accumulator pressure sensor output value and the state of the pump motor.

Chassis > Brake Booster > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ECB Motor Relay Motor relay operation request OFF / ON OFF: Relay off
ON: Relay on
ECB: Electronically Controlled Brake System
Accumulator Pressure Accumulator pressure output value Min.: 0.00 MPa
Max.: 24.48 MPa
15.00 to 21.00 MPa (Pressure stable and pump motor stopped) When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator
Chassis > Brake Booster > Data List
Tester Display
ECB Motor Relay
Accumulator Pressure
50003 466 96,212
Result:
Result Proceed to
The drop in the accumulator pressure sensor output value is less than 2.50 MPa 30 seconds after the pump motor stops, and the pump motor does not operate within 30 seconds after the pump motor stops. A
The drop in the accumulator pressure sensor output value is 2.50 MPa or more 30 seconds after the pump motor stops, or the pump motor operates within 30 seconds after the pump motor stops. B





A

3.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

CHECK AND REPAIR BRAKE FLUID LEAKS OR ADD FLUID

3.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

Pre-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the A2 brake pedal stroke sensor assembly connector.


c.

Remove the brake master cylinder reservoir filler cap assembly.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the A12 brake fluid level warning switch (brake booster with master cylinder assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.
C220166C06
1.49,0.26 1.917,0.5 0.427,0.24 1.938,1.229 2.479,0.844 true 1.49,1.229 0.938,0.844 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.573,0.302 1.958,0.49 0.385,0.188 10 false A12 2.542,0.74 2.927,0.927 0.385,0.188 10 false + 0.823,0.677 1.104,0.865 0.281,0.188 10 false E
*a Component without harness connected
(Brake Fluid Level Warning Switch (Brake Booster with Master Cylinder Assembly))


Measure the resistance according to the value(s) in the table below.

HINT:

A float is located inside the brake fluid level warning switch (brake booster with master cylinder assembly). Its position changes according to the level of brake fluid.


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A12)Location & Routing

Click Connector(A12)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Fluid Level Warning Switch (Brake Booster with Master Cylinder Assembly)

A12-1 (+) - A12-2 (E) Brake fluid level warning switch (brake booster with master cylinder assembly) off (float up) 1.84 to 2.16 kΩ
A12-1 (+) - A12-2 (E) Brake fluid level warning switch (brake booster with master cylinder assembly) on (float down) Below 1 Ω
(Brake fluid level is low)



b.

If there are no problems after completing the preceding inspection, adjust the brake fluid to the MAX level with the ignition switch turned to ON.

Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

4.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE FLUID LEVEL WARNING SWITCH (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY))

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE FLUID LEVEL WARNING SWITCH (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY))

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the A5 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A5,A12)Location & Routing

Click Connector(A5)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Booster with Master Cylinder Assembly

Click Connector(A12)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Fluid Level Warning Switch (Brake Booster with Master Cylinder Assembly)

A5-12 (LBL) - A12-1 (+) Always Below 1 Ω
A5-12 (LBL) or A12-1 (+) - Body ground Always 10 kΩ or higher
A12-2 (E) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

5.CHECK BRAKE DISC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK BRAKE DISC

Pre-procedure1

a.

Reconnect the A5 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Reconnect the A12 brake fluid level warning switch (brake booster with master cylinder assembly) connector.


c.

Disconnect the A2 brake pedal stroke sensor assembly connector.


Procedure1

a.

Perform a road test according to Freeze Frame Data or customer problem analysis. While driving, check for abnormal brake pedal vibration caused by brake discs that are worn or have excess runout.

OK:

Brake pedal does not vibrate during braking.


HINT:
·

An unevenly worn disc may vibrate the caliper pistons and cause fluctuations in brake line pressure, triggering a malfunction detection condition.

·

The brake pedal does not kick back due to caliper piston vibration during electronically controlled brake system control.

·

If the brake pedal stroke sensor assembly connector is disconnected, the fail-safe function will prohibit electronically controlled brake system control.

·

The Active Test does not prohibit electronically controlled brake system control when the vehicle is being driven, so disconnect the brake pedal stroke sensor assembly connector before continuing with inspection.

·

Uneven disc wear can be checked by measuring the disc thickness variation.



Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

6.CLEAR DTC

NG

REPLACE BRAKE DISC

6.CLEAR DTC

Pre-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the A2 brake pedal stroke sensor assembly connector.


Procedure1

a.

Clear the DTCs.

Chassis > Brake Booster > Clear DTCs
50002 466
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

7.RECONFIRM DTC
7.RECONFIRM DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


Procedure1

a.

Check if the same DTC is output.

Chassis > Brake Booster > Trouble Codes
50001 466
Result:
Result Proceed to
C126E15 is not output A
C126E15 is output B



Post-procedure1

a.

None



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY