Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0459129 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  P05FF62  Brake Pressure Sensor / Brake Pedal Position Sensor Signal Compare Failure  


DESCRIPTION

If the No. 1 skid control ECU (brake booster with master cylinder assembly) detects an inconsistency between the brake pedal stroke sensor assembly signal and reaction force pressure sensor signal, DTC P05FF62 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
P05FF62 Brake Pressure Sensor / Brake Pedal Position Sensor Signal Compare Failure The difference between brake pedal stroke sensor assembly output value and reaction force pressure sensor output value is above the threshold for a certain period of time.
·

Brake booster with master cylinder assembly

·

Brake pedal stroke sensor assembly

·

Brake pedal stroke sensor assembly installation

·

Brake fluid leaks


Brake Booster A Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing or reinstalling the brake pedal stroke sensor assembly, perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY

·

After replacing the No. 1 skid control ECU (brake booster with master cylinder assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY

·

If the detection conditions for X21D2 are met 3 times in a row in the same trip, DTC P05FF62 is stored.



PROCEDURE

1.CUSTOMER PROBLEM ANALYSIS (CHECK CONDITION WHEN MALFUNCTION OCCURRED) AND FREEZE FRAME DATA

Pre-procedure1

a.

Interview the customer to check the vehicle conditions when the brake system warning light (red indicator) and brake system warning light (yellow indicator) illuminated.


Procedure1

a.

Using the GTS, check for Freeze Frame Data that is recorded when a DTC is stored.

HINT:

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>FREEZE FRAME DATA


Chassis > Brake Booster > Trouble Codes
50001 466
HINT:
·

Freeze Frame Data is only stored once when a DTC is stored.

·

If other DTCs are output, repair any malfunctions related to those DTCs first, and then reproduce the conditions that caused DTC P05FF62 to be stored based on the interview with the customer.



Result:
Proceed to
NEXT



Post-procedure1

a.

None



NEXT

2.READ VALUE USING GTS (BRAKE PEDAL STROKE SENSOR ASSEMBLY)
2.READ VALUE USING GTS (BRAKE PEDAL STROKE SENSOR ASSEMBLY)
a.

With the brake pedal released, confirm the brake pedal stroke sensor assembly output voltage.

Chassis > Brake Booster > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stroke Sensor Brake pedal stroke sensor 1 Min.: 0.0 V
Max.: 5.0 V
Brake pedal released: 0.6 to 1.4 V Reading increases when brake pedal is depressed
Chassis > Brake Booster > Data List
Tester Display
Stroke Sensor
50003 466 207

Result:
Result Proceed to
The value of Stroke Sensor is between 0.6 and 1.4 V A
None of the above conditions are met B



A

3.READ VALUE USING GTS (BRAKE PEDAL STROKE SENSOR ASSEMBLY)

B

3.READ VALUE USING GTS (BRAKE PEDAL STROKE SENSOR ASSEMBLY)

Pre-procedure1

a.

Turn the ignition switch off.


b.

Mount a pedal effort gauge.


c.

Turn the ignition switch to ON (READY) and depress the brake pedal once.

HINT:

Depress the brake pedal after turning the ignition switch to ON (READY) to set the vehicle to linear mode (switching solenoid (SSA) on).



Procedure1

a.

Depress the brake pedal slowly and check the brake pedal stroke sensor assembly output voltages with respect to brake pedal depression force.

Chassis > Brake Booster > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stroke Sensor Brake pedal stroke sensor 1 Min.: 0.0 V
Max.: 5.0 V
Brake pedal released: 0.6 to 1.4 V Reading increases when brake pedal is depressed
Chassis > Brake Booster > Data List
Tester Display
Stroke Sensor
50003 466 207
HINT:

Perform this procedure in linear mode (switching solenoid (SSA) on).


Standard Voltage:
Brake Effort
[N (kgf, lbf)]
Stroke Sensor
[V]
50 (5.1, 11.2) 1.21 to 1.91
100 (10.2, 22.5) 1.42 to 2.12
150 (15.3, 33.7) 1.61 to 2.31


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

4.READ VALUE USING GTS (REACTION FORCE PRESSURE)

NG

4.READ VALUE USING GTS (REACTION FORCE PRESSURE)
a.

Depress the brake pedal slowly and check the reaction force pressure sensor output values with respect to brake pedal depression force.

Chassis > Brake Booster > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Reaction Force Pressure Pressure value of stroke simulator Min.: 0.00 MPa
Max.: 24.48 MPa
Brake pedal released: 0.00 to 1.53 MPa Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal
Chassis > Brake Booster > Data List
Tester Display
Reaction Force Pressure
50003 466 205
HINT:

Perform this procedure in linear mode (switching solenoid (SSA) on).


Standard Pressure:
Brake Effort
[N (kgf, lbf)]
Reaction Force Pressure
[MPa]
50 (5.1, 11.2) 0.00 to 0.64
100 (10.2, 22.5) 0.52 to 1.32
150 (15.3, 33.7) 1.17 to 1.97
200 (20.4, 45.0) 1.85 to 2.65



Result:
Proceed to
OK
NG



OK

5.CLEAR DTC

NG

CHECK AND REPAIR BRAKE FLUID LEAKS

5.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Chassis > Brake Booster > Clear DTCs
50002 466
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

6.RECONFIRM DTC
6.RECONFIRM DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


Procedure1

a.

Check if the same DTC is output.

Chassis > Brake Booster > Trouble Codes
50001 466
Result:
Result Proceed to
P05FF62 is not output A
P05FF62 is output B



Post-procedure1

a.

None



A

END

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY