Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0459129 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C050014  Left Front Wheel Speed Sensor Circuit Short to Ground or Open  


DESCRIPTION

Refer to DTC C050012.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C050012

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
C050014 Left Front Wheel Speed Sensor Circuit Short to Ground or Open An open in the speed sensor signal circuit continues for 0.5 seconds or more.
·

Front speed sensor LH (front axle hub sub-assembly LH)

·

Front skid control sensor wire LH

·

Wire harness and connector

·

No. 2 skid control ECU (brake actuator assembly)


Brake/EPB A Output ECU: No. 2 skid control ECU (brake actuator assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY

·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE



PROCEDURE

1.READ VALUE USING GTS (MOMENTARY INTERRUPTION)

Pre-procedure1

a.

Select the line graph display on the GTS.


Procedure1

a.

Check for any momentary interruption in the wire harness and connector.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FL Speed Open Momentary interruption of front speed sensor LH pulse input to ECU Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
-
FL Speed Sensor Voltage Open Front speed sensor LH voltage open detection Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
-
Chassis > Brake/EPB > Data List
Tester Display
FL Speed Open
FL Speed Sensor Voltage Open
50003 435 102,111
NOTICE:

Perform the above inspection before removing the sensor and connector.


OK:

Normal (There are no momentary interruptions.)


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

2.INSPECT FRONT SKID CONTROL SENSOR WIRE LH
2.INSPECT FRONT SKID CONTROL SENSOR WIRE LH

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the AW1 front skid control sensor wire LH connector.


b.

Disconnect the W1 front skid control sensor wire LH connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(W1,AW1)Location & Routing

Click Connector(W1)Engine Compartment>Front Skid Control Sensor Wire LH / Front Skid Control Sensor Wire RH>Front Speed Sensor LH (Front Axle Hub Sub-Assembly LH)

Click Connector(AW1)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Front Compartment Main Wire and Front Skid Control Sensor Wire LH

W1-2 (FL+) - AW1-3 Always Below 1 Ω
W1-2 (FL+) or AW1-3 - Body ground and other terminals Always 10 kΩ or higher
W1-1 (FL-) - AW1-1 Always Below 1 Ω
W1-1 (FL-) or AW1-1 - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

3.CHECK HARNESS AND CONNECTOR (FRONT SKID CONTROL SENSOR WIRE LH - BRAKE ACTUATOR ASSEMBLY)

NG

REPLACE FRONT SKID CONTROL SENSOR WIRE LH

3.CHECK HARNESS AND CONNECTOR (FRONT SKID CONTROL SENSOR WIRE LH - BRAKE ACTUATOR ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A6 No. 2 skid control ECU (brake actuator assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(AW1,A6)Location & Routing

Click Connector(AW1)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Front Compartment Main Wire and Front Skid Control Sensor Wire LH

Click Connector(A6)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Actuator Assembly

AW1-3 - A6-22 (FL+) Always Below 1 Ω
AW1-3 or A6-22 (FL+) - Body ground Always 10 kΩ or higher
AW1-1 - A6-21 (FL-) Always Below 1 Ω
AW1-1 or A6-21 (FL-) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

4.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR POWER SOURCE CIRCUIT)

Pre-procedure1

a.

Reconnect the A6 No. 2 skid control ECU (brake actuator assembly) connector.


b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(AW1)Location & Routing

Click Connector(AW1)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Front Compartment Main Wire and Front Skid Control Sensor Wire LH

AW1-3 - Body ground Ignition switch ON 11 to 14 V


HINT:

The front speed sensor rotor LH and front speed sensor LH are incorporated into the front axle hub sub-assembly LH.

If the front speed sensor LH and front speed sensor rotor LH needs to be replaced, replace the front axle hub sub-assembly LH.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE FRONT AXLE HUB SUB-ASSEMBLY LH

NG