Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0459129 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C050C3A  Left Rear Wheel Speed Sensor Signal Has Too Many Pulses  C05123A  Right Rear Wheel Speed Sensor Signal Has Too Many Pulses  


DESCRIPTION

Refer to DTC C050C12.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C050C12

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
C050C3A Left Rear Wheel Speed Sensor Signal Has Too Many Pulses Either of the following is detected:
·

When not in Dealer Mode (Signal Check) or Inspection Mode, the output of the speed sensor detected by the No. 2 skid control ECU (brake actuator assembly) is too high for 5 seconds or more.

·

When not in Dealer Mode (Signal Check) or Inspection Mode, the speed sensor detects 3 or more wheels in reverse at a vehicle speed exceeding 3 km/h (1.86 mph), and the vehicle pulse width less than 0.000302 seconds generates 75 times or more.


No. 2 skid control ECU (brake actuator assembly) Brake/EPB A Output ECU: No. 2 skid control ECU (brake actuator assembly)
C05123A Right Rear Wheel Speed Sensor Signal Has Too Many Pulses Either of the following is detected:
·

When not in Dealer Mode (Signal Check) or Inspection Mode, the output of the speed sensor detected by the No. 2 skid control ECU (brake actuator assembly) is too high for 5 seconds or more.

·

When not in Dealer Mode (Signal Check) or Inspection Mode, the speed sensor detects 3 or more wheels in reverse at a vehicle speed exceeding 3 km/h (1.86 mph), and the vehicle pulse width less than 0.000302 seconds generates 75 times or more.


No. 2 skid control ECU (brake actuator assembly) Brake/EPB A Output ECU: No. 2 skid control ECU (brake actuator assembly)

C050C3A DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition When not in Dealer Mode (Signal Check) or Inspection Mode ○ ○
Malfunction Status When the output of the speed sensor detected by the No. 2 skid control ECU (brake actuator assembly) is too high ○ -
When the speed sensor detects 3 or more wheels in reverse at a vehicle speed exceeding 3 km/h (1.86 mph), and the vehicle pulse width is less than 0.000302 seconds - ○
Detection Time 5 seconds or more. 75 times or more.
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


C05123A DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition When not in Dealer Mode (Signal Check) or Inspection Mode ○ ○
Malfunction Status When the output of the speed sensor detected by the No. 2 skid control ECU (brake actuator assembly) is too high ○ -
When the speed sensor detects 3 or more wheels in reverse at a vehicle speed exceeding 3 km/h (1.86 mph), and the vehicle pulse width is less than 0.000302 seconds - ○
Detection Time 5 seconds or more. 75 times or more.
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY


PROCEDURE

1.REPLACE BRAKE ACTUATOR ASSEMBLY

NEXT

END