Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0459129 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C050C12  Left Rear Wheel Speed Sensor Circuit Short to Battery  


DESCRIPTION

The speed sensor detects wheel speed and sends the appropriate signals to the No. 2 skid control ECU (brake actuator assembly). These signals are used for brake control.

Speed sensor rotors have rows of alternating N and S magnetic poles, and their magnetic fields change when the rotors turn.

Each speed sensor detects that magnetic change and sends a pulse signal to the No. 2 skid control ECU (brake actuator assembly).

HINT:

When the connectors between the speed sensor and No. 2 skid control ECU (brake actuator assembly) are connected, the following waveform is output.


C435285E01
3.656,1.104 4.333,1.333 4.333,1.333 4.5,1.333 true 4.573,1.25 5.646,1.458 1.073,0.208 10 false Speed Sensor 2.042,2.167 2.844,2.365 0.802,0.198 10 false Backward 4.604,2.167 5.406,2.365 0.802,0.198 10 false Forward 3,3.25 4.438,3.458 1.438,0.208 10 false Speed Sensor Rotor 6.542,3.927 7.073,4.156 0.531,0.229 10 false 2.6 V 6.531,4.813 7.052,5.031 0.521,0.219 10 false 1.4 V 6.542,5.271 7.073,5.469 0.531,0.198 10 false 0.7 V 1.917,6.25 2.719,6.448 0.802,0.198 10 false Backward 3,6.25 3.802,6.448 0.802,0.198 10 false Forward 3.729,5.75 4.542,5.948 0.813,0.198 10 false Low speed 5.146,5.75 5.958,5.948 0.813,0.198 10 false High speed

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
C050C12 Left Rear Wheel Speed Sensor Circuit Short to Battery The speed sensor short signal is ON continuously for 0.5 seconds or more.
·

Rear speed sensor LH

·

Rear skid control sensor wire LH

·

Wire harness and connector

·

No. 2 skid control ECU (brake actuator assembly)


Brake/EPB A Output ECU: No. 2 skid control ECU (brake actuator assembly)

WIRING DIAGRAM

C449381E06
0.135,2.26 1.604,2.667 1.469,0.406 10 false Rear Speed Sensor LH 1.823,2.26 4.167,2.667 2.344,0.406 10 false Rear Skid Control Sensor Wire LH 5.188,3.083 7.104,3.698 1.917,0.615 10 false No. 2 Skid Control ECU (Brake Actuator Assembly) 5.792,1.26 6.292,1.469 0.5,0.208 10 false RL+ 1.198,1.115 1.51,1.385 0.313,0.271 10 false RL+ 1.198,1.802 1.479,2.073 0.281,0.271 10 false RL- 5.802,1.948 6.365,2.156 0.563,0.208 10 false RL- 1.594,1.125 2.073,1.292 0.479,0.167 10 false W3 1.594,1.823 1.927,2.073 0.333,0.25 10 false W3 3.167,1.125 3.656,1.344 0.49,0.219 10 false WG2 3.177,1.823 3.594,2.125 0.417,0.302 10 false WG2 1.698,0.906 2,1.135 0.302,0.229 10 false 2 5.188,2.896 5.688,3.094 0.5,0.198 10 false A6 1.688,1.604 1.99,1.833 0.302,0.229 10 false 1 3.281,0.906 3.583,1.135 0.302,0.229 10 false 3 3.292,1.604 3.594,1.833 0.302,0.229 10 false 4 5.583,1.031 5.875,1.271 0.292,0.24 10 false 5 5.573,1.719 5.927,1.969 0.354,0.25 10 false 4

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY

·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the W3 rear speed sensor LH connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Pre-procedure2

a.

Turn the ignition switch to ON.


Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(W3)Location & Routing

Click Connector(W3)Body>Rear Skid Control Sensor Wire LH / Rear Skid Control Sensor Wire RH>Rear Speed Sensor LH

W3-2 (RL+) - W3-1 (RL-) Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

2.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the WG2 rear skid control sensor wire LH connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Pre-procedure3

a.

Turn the ignition switch to ON.


Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(WG2)Location & Routing

Click Connector(WG2)Body>Rear Skid Control Sensor Wire LH / Rear Skid Control Sensor Wire RH>Rear Skid Control Sensor Wire LH and Floor Wire

WG2-3 - WG2-4 Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE REAR SKID CONTROL SENSOR WIRE LH

NG

3.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)
3.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the A6 No. 2 skid control ECU (brake actuator assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(WG2)Location & Routing

Click Connector(WG2)Body>Rear Skid Control Sensor Wire LH / Rear Skid Control Sensor Wire RH>Rear Skid Control Sensor Wire LH and Floor Wire

WG2-4 - Body ground Always Below 1.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

4.CHECK HARNESS AND CONNECTOR (REAR SKID CONTROL SENSOR WIRE LH - BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (REAR SKID CONTROL SENSOR WIRE LH - BRAKE ACTUATOR ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(WG2,A6)Location & Routing

Click Connector(WG2)Body>Rear Skid Control Sensor Wire LH / Rear Skid Control Sensor Wire RH>Rear Skid Control Sensor Wire LH and Floor Wire

Click Connector(A6)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Actuator Assembly

WG2-3 or A6-5 (RL+) - WG2-4 or A6-4 (RL-) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR