Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0459129 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C124A00  ECM Communication  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
C124A00 ECM Communication Either of the following is detected:
·

The engine type, powertrain variation and destination information sent from the EV control ECU do not match the information stored in the No. 2 skid control ECU (brake actuator assembly).

·

No system information stored in the No. 2 skid control ECU (brake actuator assembly).


·

Incorrect EV control ECU installed

·

No. 2 skid control ECU (brake actuator assembly)


Brake/EPB A Output ECU: No. 2 skid control ECU (brake actuator assembly)

C124A00 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition - - -
Malfunction Status The engine type, powertrain variation and destination information sent from the EV control ECU do not match the information stored in the No. 2 skid control ECU (brake actuator assembly) ○ -
No system information stored in the No. 2 skid control ECU (brake actuator assembly) - ○
Detection Time - -
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY


PROCEDURE

1.CHECK PART NUMBER (EV CONTROL ECU)
a.

Check that the proper EV control ECU is installed.

OK:

Proper EV control ECU is installed.



Result:
Proceed to
OK
NG



OK

2.CHECK PART NUMBER (BRAKE ACTUATOR ASSEMBLY)

NG

2.CHECK PART NUMBER (BRAKE ACTUATOR ASSEMBLY)
a.

Check that the proper No. 2 skid control ECU (brake actuator assembly) is installed.

OK:

Proper No. 2 skid control ECU (brake actuator assembly) is installed.



Result:
Proceed to
OK
NG



OK

3.CLEAR SYSTEM INFORMATION

NG

3.CLEAR SYSTEM INFORMATION
a.

Clear system information.

HINT:

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY


Chassis > Brake/EPB > Utility
Tester Display
Reset Memory
50005 435 4560

Result:
Proceed to
NEXT



NEXT

4.SYSTEM INFORMATION MEMORIZATION
4.SYSTEM INFORMATION MEMORIZATION
a.

Perform system information memorization.

HINT:

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY


Chassis > Brake/EPB > Utility
Tester Display
Calibration
50005 435 4554
HINT:

After performing "Reset Memory" using the GTS to clear the memorized value of the No. 2 skid control ECU (brake actuator assembly), DTC C124A00 will be stored until system information memorization is performed.



Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

6.RECONFIRM DTC
6.RECONFIRM DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


Procedure1

a.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435
Result:
Result Proceed to
C124A00 is not output A
C124A00 is output B



Post-procedure1

a.

None



A

END

B