Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0459129 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C140000  Brake Pressure Leak Malfunction  C140A00  Pressure Control Reservoir Leak Malfunction  


DESCRIPTION

The No. 2 skid control ECU (brake actuator assembly) controls the brake fluid pressure of each wheel cylinder based on the brake fluid pressure sensor.

DTCs may be stored if one of the following occurs:

·

Brake fluid leaks.

·

Foreign matter enters a solenoid valve.

·

Brake pads are replaced.

·

Rotors are replaced.

HINT:

When replacing the brake pads, retracting the brake caliper pistons and installing new brake pads will greatly increase the clearance between the brake pads and brake discs. This will result in a significant possibility of this DTC being stored the next time the brake pedal is depressed. As this is not a malfunction, clear the DTC if it is stored for this reason.



DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
C140000 Brake Pressure Leak Malfunction When all of the following conditions are met, a malfunction such as a leak in an ABS decrease pressure valve of the brake actuator assembly is detected:
·

The vehicle was driven before the ignition switch was turned off.

·

90 seconds have elapsed since the ignition switch was turned off.

·

The vehicle is stopped and the shift position is P.


·

Brake booster with master cylinder assembly

·

Brake actuator assembly


Brake/EPB A Output ECU: No. 2 skid control ECU (brake actuator assembly)
C140A00 Pressure Control Reservoir Leak Malfunction When all of the following conditions are met, a malfunction is detected by the No. 2 skid control ECU (brake actuator assembly) during self-diagnosis.
·

The vehicle was driven before the ignition switch was turned off.

·

90 seconds have elapsed since the ignition switch was turned off.

·

The vehicle is stopped and the shift position is P.


·

Brake booster with master cylinder assembly

·

Brake actuator assembly


Brake/EPB A Output ECU: No. 2 skid control ECU (brake actuator assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the No. 1 skid control ECU (brake booster with master cylinder assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY

·

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY



PROCEDURE

1.INSPECT WHEEL CYLINDER PRESSURE

Pre-procedure1

a.

Mount a pedal effort gauge.


b.

Disconnect the A39 brake booster pump assembly connector.


c.

Depress the brake pedal 10 times or more until it becomes hard.

HINT:

Depressing the brake pedal with the connector of the brake booster pump assembly disconnected drops the accumulator pressure to approximately 0 MPa.



d.

Connect an LSPV gauge set.


Procedure1

a.

Slowly depress the brake pedal and check the wheel cylinder pressure with respect to brake pedal depression force.

NOTICE:

Check the wheel cylinder pressure with the switching solenoid (SSA, SGH) off and an accumulator pressure of 0 MPa.


Standard Hydraulic Pressure:
for Front Right Wheel
Brake Effort
[N (kgf, lbf)]
Specified Condition
200 (20.4, 45.0) 0.00 to 2.86 (0.0 to 29.2, 0 to 415)
500 (51.0, 112.4) 1.16 to 5.16 (11.8 to 52.6, 168 to 748)

for Rear Right Wheel
Brake Effort
[N (kgf, lbf)]
Specified Condition
200 (20.4, 45.0) 0.00 to 2.86 (0.0 to 29.2, 0 to 415)
500 (51.0, 112.4) 1.16 to 5.16 (11.8 to 52.6, 168 to 748)


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

2.CLEAR DTC

NG

5.INSPECT BRAKE FLUID LEAKS
2.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

3.RECONFIRM DTC
3.RECONFIRM DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


Procedure1

a.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435
Result:
Result Proceed to
C140000 and C140A00 are not output A
C140000 or C140A00 is output B
Only C140A00 is output C



Post-procedure1

a.

None



A

B

C

4.RECONFIRM DTC
4.RECONFIRM DTC
a.

Check the DTCs that are output.

Chassis > Brake Booster > Trouble Codes
50001 466

Result:
Result Proceed to
C139A00 is output A
DTCs are not output B



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY AND BRAKE ACTUATOR ASSEMBLY

for Brake Booster with Master Cylinder Assembly for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD)>REMOVAL

for Brake Booster with Master Cylinder Assembly for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD)>REMOVAL

for Brake Actuator Assembly for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for LHD)>REMOVAL

for Brake Actuator Assembly for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for RHD)>REMOVAL


B

5.INSPECT BRAKE FLUID LEAKS
a.

Brake fluid leaks and air in brake line inspection

i.

Check and take a note of the fluid level in the brake master cylinder reservoir assembly (brake booster with master cylinder assembly).


ii.

Repeatedly depress the brake pedal and confirm that the brake pedal feels normal (no air in the system, etc.).


iii.

Check if the brake fluid level in the brake master cylinder reservoir assembly (brake booster with master cylinder assembly) has changed.


iv.

If the brake fluid level has decreased, check for leaks due to damaged brake lines or hoses, loose union nuts, damaged brake master cylinder assembly seals, etc.



OK:

There are no brake fluid leaks and no air in the system.


Result:
Proceed to
OK
NG



OK

NG

REPAIR BRAKE FLUID LEAKS AND ADD FLUID