Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0459129 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C050C23  Left Rear Wheel Speed Sensor Signal Stuck Low  


DESCRIPTION

Refer to DTC C050C12.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C050C12

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
C050C23 Left Rear Wheel Speed Sensor Signal Stuck Low Any of the following is detected:
·

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 30 seconds or more.

·

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.

·

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h or more, output from the 2 speed sensors is 0 km/h (0 mph) for a total of 200 seconds.


·

Rear speed sensor LH

·

Rear speed sensor installation

·

Rear skid control sensor wire LH

·

Wire harness and connector

·

Rear speed sensor rotor LH (rear axle hub and bearing assembly LH)


Brake/EPB A Output ECU: No. 2 skid control ECU (brake actuator assembly)

C050C23 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition When the +BS terminal voltage is 17.4 V or less ○ ○ ○
Malfunction Status At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors ○ - -
At a vehicle speed of 10 km/h (6 mph) or more, output from one of the speed sensors is 0 km/h (0 mph) - ○ -
At a vehicle speed of 10 km/h (6 mph) or more, outputs from the 2 speed sensors is 0 km/h (0 mph) - - ○
Detection Time 30 seconds or more. 1 second or more. Total of 200 seconds.
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:
·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE

·

After replacing or removing and installing a speed sensor rotor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE



PROCEDURE

1.CHECK REAR SPEED SENSOR LH INSTALLATION
a.
C168336C07
0.76,1.917 1.083,2.083 0.323,0.167 10 *a 2.417,1.917 2.74,2.083 0.323,0.167 10 *b
*a Correct
*b Incorrect


Check the rear speed sensor LH installation.

OK:

There is no clearance between the rear speed sensor LH and the rear axle carrier LH.



Result:
Proceed to
OK
NG



OK

2.CHECK REAR SPEED SENSOR LH (CHECK FOR FOREIGN MATTER)

NG

REINSTALL OR REPLACE REAR SPEED SENSOR LH

2.CHECK REAR SPEED SENSOR LH (CHECK FOR FOREIGN MATTER)

Pre-procedure1

a.

Remove the rear speed sensor LH.

HINT:

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>REMOVAL



Procedure1

a.

Check the rear speed sensor tip LH.

OK:

The rear speed sensor tip LH is free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the rear speed sensor LH, clean the rear speed sensor LH.

·

If the rear speed sensor LH is damaged, replace the rear speed sensor LH with a new one.



Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

3.READ VALUE USING GTS (RL WHEEL SPEED)

NG

CLEAN OR REPLACE REAR SPEED SENSOR LH

3.READ VALUE USING GTS (RL WHEEL SPEED)

Pre-procedure1

a.

Perform a road test.


Procedure1

a.

Check the rear speed sensor LH output value.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0.0 km/h (0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake/EPB > Data List
Tester Display
RL Wheel Speed
50003 435 16
OK:

The output value changes in accordance with the vehicle speed.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

4.INSPECT REAR SKID CONTROL SENSOR WIRE LH
4.INSPECT REAR SKID CONTROL SENSOR WIRE LH

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the W3 rear skid control sensor wire LH connector.


b.

Disconnect the WG2 rear skid control sensor wire LH connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(W3,WG2)Location & Routing

Click Connector(W3)Body>Rear Skid Control Sensor Wire LH / Rear Skid Control Sensor Wire RH>Rear Speed Sensor LH

Click Connector(WG2)Body>Rear Skid Control Sensor Wire LH / Rear Skid Control Sensor Wire RH>Rear Skid Control Sensor Wire LH and Floor Wire

W3-2 (RL+) - WG2-3 Always Below 1 Ω
W3-2 (RL+) or WG2-3 - Body ground and other terminals Always 10 kΩ or higher
W3-1 (RL-) - WG2-4 Always Below 1 Ω
W3-1 (RL-) or WG2-4 - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

5.CHECK HARNESS AND CONNECTOR (REAR SKID CONTROL SENSOR WIRE LH - BRAKE ACTUATOR ASSEMBLY)

NG

REPLACE REAR SKID CONTROL SENSOR WIRE LH

5.CHECK HARNESS AND CONNECTOR (REAR SKID CONTROL SENSOR WIRE LH - BRAKE ACTUATOR ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A6 No. 2 skid control ECU (brake actuator assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A6,WG2)Location & Routing

Click Connector(A6)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Actuator Assembly

Click Connector(WG2)Body>Rear Skid Control Sensor Wire LH / Rear Skid Control Sensor Wire RH>Rear Skid Control Sensor Wire LH and Floor Wire

A6-5 (RL+) - WG2-3 Always Below 1 Ω
A6-5 (RL+) or WG2-3 - Body ground Always 10 kΩ or higher
A6-4 (RL-) - WG2-4 Always Below 1 Ω
A6-4 (RL-) or WG2-4 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

6.CHECK REAR SPEED SENSOR ROTOR LH (CHECK FOR FOREIGN MATTER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK REAR SPEED SENSOR ROTOR LH (CHECK FOR FOREIGN MATTER)

Pre-procedure1

a.

Remove the component with the rear speed sensor rotor LH.

HINT:

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>REMOVAL



Procedure1

a.

Check the rear speed sensor rotor LH.

OK:

The rear speed sensor rotor LH is free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the rear speed sensor rotor LH, clean the rear speed sensor rotor LH.

·

Do not use parts cleaner when cleaning the rear speed sensor rotor LH.

·

If the rear speed sensor rotor LH is damaged, replace the rear speed sensor rotor LH with a new one.



HINT:

The rear speed sensor rotor LH is incorporated into the rear axle hub and bearing assembly LH.

If the rear speed sensor rotor LH needs to be replaced, replace it together with the rear axle hub and bearing assembly LH.


Result:
Result Proceed to
OK A
NG (The rear speed sensor rotor LH is damaged.) B
NG (There is foreign matter on the rear speed sensor rotor LH.) C



Post-procedure1

a.

None



A

B

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY LH

C

CLEAN REAR SPEED SENSOR ROTOR LH