Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0459129 ELECTRONICALLY CONTROLLED BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  Brake Hold Standby Indicator Light Circuit  


DESCRIPTION

The brake hold standby indicator light turns on if brake hold switch (electric parking brake switch assembly)is possible when the following conditions required for operation standby are met and the brake hold switch is pressed while the ignition switch is turned to ON.

Conditions required for operation standby:

(a)

The driver door is closed.

(b)

The driver seat belt is fastened.

(c)

The system is normal.



WIRING DIAGRAM

C427349E12
0.906,0.906 1.521,1.104 0.615,0.198 10 false CANL 0.885,1.74 1.5,1.938 0.615,0.198 10 false CANH 1.406,0.74 1.719,0.938 0.313,0.198 10 false 30 1.406,1.552 1.719,1.75 0.313,0.198 10 false 29 5.073,0.74 5.385,0.938 0.313,0.198 10 false 43 5.073,1.552 5.385,1.75 0.313,0.198 10 false 27 5.365,0.927 5.979,1.125 0.615,0.198 10 false CANL 5.365,1.74 5.979,1.938 0.615,0.198 10 false CANH 3.396,2.74 3.667,3 0.271,0.26 10 false 12 4.542,2.75 4.813,3 0.271,0.25 10 false 10 0.115,3.906 0.573,4.104 0.458,0.198 10 false D41 2.906,3.188 3.365,3.385 0.458,0.198 10 false D51 2.885,3.406 5.24,3.865 2.354,0.458 10 false Brake Hold Switch (Electric Parking Brake Switch Assembly) 3.667,2.99 3.823,3.188 0.156,0.198 10 false E 4.219,2.99 4.656,3.219 0.438,0.229 10 false +B 5.073,2.76 5.385,2.958 0.313,0.198 10 false 35 5.344,3.052 5.802,3.25 0.458,0.198 10 false PKB 5.135,3.938 5.594,4.135 0.458,0.198 10 false A6 5.125,4.104 7.052,4.51 1.927,0.406 10 false No. 2 Skid Control ECU (Brake Actuator Assembly) 2.906,4.344 6.573,4.542 3.667,0.198 10 false : CAN Communication Line 0.115,4.073 4.094,4.271 3.979,0.198 10 false Combination Meter Assembly

CAUTION / NOTICE / HINT

NOTICE:

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY


PROCEDURE

1.PRE-CHECK
a.

If the brake hold standby indicator light does not illuminate even though the brake hold switch is pushed, check that the brake hold function operation conditions are met.

1.

The driver door is closed.

2.

The driver seat belt is fastened.

3.

The system is normal.


HINT:

If a malfunction occurs in one of the following systems, the brake hold operated indicator light will blink. If this occurs, perform troubleshooting on the malfunctioning system.

·

Brake system

·

Electric parking brake system

·

Hybrid control system




Result:
Proceed to
NEXT



NEXT

2.READ VALUE USING GTS (BRAKE HOLD READY)
2.READ VALUE USING GTS (BRAKE HOLD READY)
a.

Check the brake hold standby indicator light and mode condition on the GTS changes according to brake hold switch (electric parking brake switch assembly) operation.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Brake Hold Ready Brake hold control permission status Not in stand-by mode / Stand-by mode Not in stand-by mode: Brake hold function not operating (brake hold standby indicator light not illuminated)
Stand-by mode: Brake hold function stand-by state (brake hold standby indicator light illuminated)
-
Chassis > Brake/EPB > Data List
Tester Display
Brake Hold Ready
50003 435 164
Standard:
Brake Hold Switch (Electric Parking Brake Switch Assembly) Operation Mode Condition Display Brake Hold Standby Indicator Light
Not pressed Not in stand-by mode Does not come on
Pressing the brake hold switch (electric parking brake switch assembly) Stand-by mode Comes on



Result:
Result Proceed to
Indicator light and mode condition display do not change. A
Mode condition display is normal, but indicator light does not change. B
Indicator light and mode condition display are normal. C



A

3.INSPECT ELECTRIC PARKING BRAKE SWITCH ASSEMBLY

B

C

3.INSPECT ELECTRIC PARKING BRAKE SWITCH ASSEMBLY

OK

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

NG

REPLACE ELECTRIC PARKING BRAKE SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A6 No. 2 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A6,D51)Location & Routing

Click Connector(A6)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Actuator Assembly

Click Connector(D51)Instrument Panel>Instrument Panel Wire>Electric Parking Brake Switch Assembly

A6-35 (PKB) - D51-10 (+B) Always Below 1 Ω
A6-35 (PKB) or D51-10 (+B) - Body ground Always 10 kΩ or higher
D51-12 (E) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR