| Code | Tester Display | Measurement Item | Trouble Area | Output ECU |
|---|---|---|---|---|
| X20D7 | Zero Point Calibration of Steering Angle Sensor Malfunction | History of the steering sensor zero point calibration position differing from the stored value | ·
Poor adjustment of the center position of the steering wheel ·
Poor adjustment of wheel alignment |
No. 2 skid control ECU (brake actuator assembly) |
After performing the inspection, check and clear the vehicle control history (RoB).
Perform the Health Check using the GTS.
| Result | Proceed to |
|---|---|
| DTCs are not output. | A |
| DTCs are output. | B |
A
B
Using the GTS, clear the Vehicle Control History (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
| Proceed to |
|---|
| NEXT |
NEXT
Clear the zero point value for the yaw rate and acceleration sensor.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY
| Tester Display |
|---|
| Reset Memory |
| Proceed to |
|---|
| NEXT |
NEXT
Perform zero point calibration of the yaw rate and acceleration sensor.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY
| Tester Display |
|---|
| Calibration |
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle straight ahead at 35 km/h (22 mph) or more for at least 5 seconds.
Drive the vehicle at 15 km/h (9 mph) or more for at least 60 seconds.
Check that the centered position of the steering wheel is correctly set while driving straight ahead.
The steering wheel is centered correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereSteering>STEERING COLUMN>STEERING SYSTEM>ON-VEHICLE INSPECTION
Normal.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
| Proceed to |
|---|
| NEXT |
NEXT
for Front: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT
for Rear: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>REAR WHEEL ALIGNMENT>ADJUSTMENT
| Proceed to |
|---|
| NEXT |
NEXT
Using the GTS, clear the Vehicle Control History (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
| Proceed to |
|---|
| NEXT |
NEXT
Clear the zero point value for the yaw rate and acceleration sensor.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY
| Tester Display |
|---|
| Reset Memory |
| Proceed to |
|---|
| NEXT |
NEXT
Perform zero point calibration of the yaw rate and acceleration sensor.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY
| Tester Display |
|---|
| Calibration |
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle straight ahead at 35 km/h (22 mph) or more for at least 5 seconds.
Drive the vehicle at 15 km/h (9 mph) or more for at least 60 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.
Using the GTS, check for Vehicle Control History (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
| Result | Proceed to |
|---|---|
| Vehicle control history (RoB) is not output. | A |
| Vehicle control history (RoB) is output. | B |
A
B