Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0459129 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C123D14  IG2 Circuit Short to Ground or Open  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the No. 2 skid control ECU (brake actuator assembly) power source voltage drops, or there is insufficient voltage to operate the main relay, the No. 2 skid control ECU (brake actuator assembly) will store a DTC.

If the auxiliary battery voltage is temporarily low, this DTC may be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
C123D14 IG2 Circuit Short to Ground or Open When communication with the EV control ECU is normal or the vehicle speed exceeds 10 km/h, no voltage (below 3.0 V and either PT1 is on or PT2 is on) is applied to the IG2 terminal and the power source voltage (exceeding 9.5 V) is applied to the IG1 terminal continuously for 4 seconds or more.
·

Open or short in IG2 circuit

·

Improperly connected connector, deformation or corrosion of terminals

·

No. 2 skid control ECU (brake actuator assembly)


Brake/EPB A Output ECU: No. 2 skid control ECU (brake actuator assembly)

C123D14 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnosis Condition When communication with the EV control ECU is normal ○ ○ - -
The vehicle speed is exceeds 10 km/h (6 mph) - - ○ ○
Malfunction Status No voltage (below 3.0 V and either PT1 is on) is applied to the IG2 terminal and the power source voltage (exceeding 9.5 V) is applied to the IG1 terminal continuously ○ - ○ ○
No voltage (below 3.0 V and either PT2 is on) is applied to the IG2 terminal and the power source voltage (exceeding 9.5 V) is applied to the IG1 terminal continuously - ○ - ○
Detection Time 4 seconds or more. 4 seconds or more. 4 seconds or more. 4 seconds or more.
Number of Trips 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before performing troubleshooting, make sure to confirm that the auxiliary battery voltage is normal.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING

·

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (IG2 TERMINAL)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A6 No. 2 skid control ECU (brake actuator assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Pre-procedure2

a.

Turn the ignition switch to ON.


Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A6)Location & Routing

Click Connector(A6)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Brake Actuator Assembly

A6-15 (IG2) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR