Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM
RM37H0E _56 Audio / Visual / Telematics _095260 AUDIO / VIDEO _0455059 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Illumination Circuit  


DESCRIPTION

Power is supplied to the radio and display receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E387203E07
0.073,0.146 1.521,0.344 1.448,0.198 10 false from PANEL D Relay 5.583,1.104 7.031,1.302 1.448,0.198 10 false to Other Systems 0.302,4.49 2.323,4.708 2.021,0.219 10 false Steering Pad Switch Assembly 2.625,4.75 4.677,4.979 2.052,0.229 10 false Spiral Cable Sub-assembly 2.667,5.688 3.813,5.896 1.146,0.208 10 false to Other Systems 2.594,2.167 2.906,2.365 0.313,0.198 10 false z5 2.604,3.906 2.917,4.104 0.313,0.198 10 false z5 2.625,3.698 2.938,3.896 0.313,0.198 10 false 6 2.625,1.948 2.938,2.146 0.313,0.198 10 false 1 3.917,1.948 4.229,2.146 0.313,0.198 10 false 14 3.938,3.698 4.25,3.896 0.313,0.198 10 false 9 3.875,2.156 4.188,2.354 0.313,0.198 10 false D32 3.865,3.917 4.177,4.115 0.313,0.198 10 false D32 3.156,2.01 3.469,2.208 0.313,0.198 10 false IL+2 3.208,3.792 3.521,3.99 0.313,0.198 10 false ILL- 5.573,2.063 5.885,2.26 0.313,0.198 10 false 15 5.583,3.813 5.896,4.01 0.313,0.198 10 false 16 5.896,2.156 6.208,2.354 0.313,0.198 10 false ILL+ 5.896,3.917 6.208,4.115 0.313,0.198 10 false ILL- 5.74,4.719 6.24,4.958 0.5,0.24 10 false D56 5.75,4.875 6.938,5.26 1.188,0.385 10 false Radio and Display Receiver Assembly 5.292,6.115 5.708,6.313 0.417,0.198 10 false D41 5.302,6.281 7.156,6.51 1.854,0.229 10 false Combination Meter Assembly 5.594,5.594 5.906,5.792 0.313,0.198 10 false 39 5.865,5.688 6.177,5.885 0.313,0.198 10 false ILL-

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

Inspect the fuse for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK METER / GAUGE SYSTEM
a.

Check if the rheostat function operates normally.

OK:

The rheostat function operates normally.



Result:
Proceed to
OK
NG



OK

2.CHECK LIGHTING SYSTEM (INT)

NG

2.CHECK LIGHTING SYSTEM (INT)
a.

Check if the instrument panel illumination comes on normally.

OK:

The instrument panel illumination comes on normally.



Result:
Proceed to
OK
NG



OK

3.CHECK ILLUMINATION

NG

3.CHECK ILLUMINATION
a.

Check if the illumination for the steering pad switch assembly or radio and display receiver assembly comes on when the light control switch is turned to the head or tail position.


Result:
Result Proceed to
Illumination for steering pad switch assembly does not come on. A
Illumination for radio and display receiver assembly does not come on. B



A

4.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL CIRCUIT)

B

7.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL CIRCUIT)
4.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL CIRCUIT)
a.

Disconnect the D32 spiral cable sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D32)Location & Routing

Click Connector(D32)Instrument Panel>Instrument Panel Wire>Spiral Cable Sub-Assembly

D32-14 (IL+2) - Body ground Ignition switch ON
Light control switch in the tail or head position
11 to 14 V



Result:
Proceed to
OK
NG



OK

5.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT STEERING PAD SWITCH ASSEMBLY

Result:
Proceed to
OK
NG



OK

6.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

6.INSPECT SPIRAL CABLE SUB-ASSEMBLY

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL CIRCUIT)
a.

Disconnect the D56 radio and display receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D56)Location & Routing

Click Connector(D56)Instrument Panel>Instrument Panel Wire>Radio Receiver Assembly

D56-15 (ILL+) - Body ground Ignition switch ON
Light control switch in tail or head position
11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the D56 radio and display receiver assembly connector.


b.

Disconnect the D41 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D56,D41)Location & Routing

Click Connector(D56)Instrument Panel>Instrument Panel Wire>Radio Receiver Assembly

Click Connector(D41)Instrument Panel>Instrument Panel Wire>Combination Meter Assembly

D56-16 (ILL-) - D41-39 (ILL-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR