Home › Power Source / Network › NETWORKING › CXPI COMMUNICATION SYSTEM
RM37H0E _57 Power Source / Network _095302 NETWORKING _0455451 CXPI COMMUNICATION SYSTEM C

NETWORKING  CXPI COMMUNICATION SYSTEM  B2353  Lost Communication with Power Integration No.2 ECU  B2354  Lost Communication with Power Integration No.3 ECU  


DESCRIPTION

This DTC is stored when CXPI communication between the semiconductor power integration ECU and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B2353 Lost Communication with Power Integration No.2 ECU No communication between No. 1 semiconductor power integration ECU and main body ECU (multiplex network body ECU) for 10 seconds or more
·

Main body ECU (multiplex network body ECU)

·

No. 1 semiconductor power integration ECU

·

Harness or connector


Main Body A
B2354 Lost Communication with Power Integration No.3 ECU No communication between No. 2 semiconductor power integration ECU and main body ECU (multiplex network body ECU) for 10 seconds or more
·

Main body ECU (multiplex network body ECU)

·

No. 2 semiconductor power integration ECU

·

Harness or connector


Main Body A

WIRING DIAGRAM

C454887E02
0.792,5.354 4.615,5.552 3.823,0.198 10 false : CXPI Communication Line 2.427,1.625 3.115,2.219 0.688,0.594 10 false 4A 1.531,1.49 2.219,2.083 0.688,0.594 10 false 5 4.354,1.635 5.042,2.229 0.688,0.594 10 false 4A 4.354,2.198 5.042,2.792 0.688,0.594 10 false 4H 1.125,1.656 1.813,2.25 0.688,0.594 10 false CXP1 2.365,1.427 3.052,2.021 0.688,0.594 10 false 30*2 5.594,1.49 6.281,2.083 0.688,0.594 10 false *3 4.302,1.417 4.99,2.01 0.688,0.594 10 false 51*1 4.292,1.99 4.979,2.583 0.688,0.594 10 false 23*1 0.427,2.406 1.729,2.99 1.302,0.583 10 false Main Body ECU (Multiplex Network Body ECU) 2.74,3.271 4.354,4.115 1.615,0.844 10 false Driver Side Junction Block Assembly 0.417,2.219 1.104,2.813 0.688,0.594 10 false D14 4.76,5.344 6.781,5.771 2.021,0.427 10 false *3: w/ PTC Heater 4.813,1.646 5.5,2.24 0.688,0.594 10 false 4A 4.813,2.208 5.5,2.802 0.688,0.594 10 false 4H 1.99,1.625 2.677,2.219 0.688,0.594 10 false 4A 4.771,1.417 5.458,2.01 0.688,0.594 10 false 52*2 4.771,1.99 5.458,2.583 0.688,0.594 10 false 32*2 2.729,5.354 4.458,5.729 1.729,0.375 10 false *1: for LHD 3.719,5.354 5.448,5.729 1.729,0.375 10 false *2: for RHD 1.917,1.427 2.604,2.021 0.688,0.594 10 false 29*1

C452814E01
2.906,0.563 3.365,0.76 0.458,0.198 10 false A59 2.865,1.021 3.323,1.219 0.458,0.198 10 false D123 2.854,1.479 3.313,1.677 0.458,0.198 10 false D123 2.917,3.5 3.375,3.698 0.458,0.198 10 false J5 2.833,4.365 3.292,4.563 0.458,0.198 10 false G102 2.854,5.49 3.313,5.688 0.458,0.198 10 false G102 2.823,7.479 3.281,7.677 0.458,0.198 10 false G102 2.844,6.875 3.302,7.073 0.458,0.198 10 false G102 3.281,5.333 3.74,5.531 0.458,0.198 10 false CXPI 3.292,4.26 3.75,4.458 0.458,0.198 10 false IG 3.302,0.469 3.76,0.667 0.458,0.198 10 false +B 3.302,6.771 3.76,6.969 0.458,0.198 10 false GND2 3.292,7.354 3.75,7.552 0.458,0.198 10 false GND1 3.781,1.469 4.24,1.667 0.458,0.198 10 false IC 4.156,5.469 4.615,5.667 0.458,0.198 10 false CPU 4.781,4.125 5.24,4.323 0.458,0.198 10 false IPD 4.781,5.135 5.24,5.333 0.458,0.198 10 false IPD 4.771,6.01 5.229,6.208 0.458,0.198 10 false IPD 4.76,6.896 5.219,7.094 0.458,0.198 10 false IPD 3.031,2.688 5.958,3.073 2.927,0.385 10 false No. 1 Semiconductor Power Integration ECU 0.802,8.458 2.583,8.75 1.781,0.292 10 false : CXPI Communication Line 3.021,8.229 5.948,8.615 2.927,0.385 10 false No. 2 Semiconductor Power Integration ECU 2.833,1.979 3.292,2.177 0.458,0.198 10 false D123 4.844,0.979 5.302,1.177 0.458,0.198 10 false IPD 4.844,1.844 5.302,2.042 0.458,0.198 10 false IPD 4.146,1.469 4.604,1.667 0.458,0.198 10 false CPU 2.969,0.802 3.427,1 0.458,0.198 10 false 9 2.948,0.344 3.406,0.542 0.458,0.198 10 false 1 2.958,1.271 3.417,1.469 0.458,0.198 10 false 7 2.906,7.229 3.365,7.427 0.458,0.198 10 false 13 2.948,3.271 3.406,3.469 0.458,0.198 10 false 1 2.969,4.125 3.427,4.323 0.458,0.198 10 false 9 2.969,5.25 3.427,5.448 0.458,0.198 10 false 7 2.958,6.635 3.417,6.833 0.458,0.198 10 false 6 2.125,3.667 3,3.958 0.875,0.292 10 false P/I NO. 3 2.125,4.51 2.719,4.885 0.594,0.375 10 false LUG-IG1 NO. 1 0.448,4.406 1.719,5.156 1.271,0.75 10 false from LUG-IG1 NO. 1 Relay 3.781,5.469 4.24,5.667 0.458,0.198 10 false IC 1,1.063 1.781,2.01 0.781,0.948 10 false from IG1 P NO. 1 Relay 2.104,0.719 2.979,1.01 0.875,0.292 10 false P/I NO. 2 1.969,1.167 2.844,1.458 0.875,0.292 10 false IG1 P NO. 2 2.917,1.771 3.375,1.969 0.458,0.198 10 false 13 5.375,0.885 5.833,1.083 0.458,0.198 10 false L 5.396,1.729 5.854,1.927 0.458,0.198 10 false L 5.25,3.792 5.802,4.042 0.552,0.25 10 false STP 5.375,4.177 5.833,4.375 0.458,0.198 10 false L 5.385,4.781 5.844,4.979 0.458,0.198 10 false L 5.375,5.219 5.833,5.417 0.458,0.198 10 false L 5.344,6.781 5.802,6.979 0.458,0.198 10 false L 5.344,5.875 5.802,6.073 0.458,0.198 10 false L 5.948,1.385 6.708,1.938 0.76,0.552 10 false To Each Load 0.656,0.094 2.396,0.438 1.74,0.344 10 false w/ PTC Heater: 6.052,5.365 6.635,5.938 0.583,0.573 10 false To Each Load 0.385,3.531 1.948,4.292 1.563,0.76 10 false from Auxiliary Battery 0.885,0.542 1.76,1.51 0.875,0.969 10 false from Auxiliary Battery 3.292,3.396 3.75,3.594 0.458,0.198 10 false +B 3.354,0.927 3.813,1.125 0.458,0.198 10 false IG 3.281,1.344 3.74,1.542 0.458,0.198 10 false CXPI 3.292,1.875 3.75,2.073 0.458,0.198 10 false GND

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off to troubleshoot:

Connect the GTS to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Recognition code registration is necessary when replacing the main body ECU (multiplex network body ECU).

·

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



PROCEDURE

1.CHECK FOR DTC

Pre-procedure1

a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

Procedure1

a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
Result:
Reasult Proceed to
B2353 and B2354 are output A
B2353 is output B
B2354 is output C



Post-procedure1

a.

None



A

2.CHECK HARNESS AND CONNECTOR (CXPI CIRCUIT)

B

6.CHECK HARNESS AND CONNECTOR (NO. 1 SEMICONDUCTOR POWER INTEGRATION ECU - BATTERY AND BODY GROUND)

C

9.CHECK HARNESS AND CONNECTOR (NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU - BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (CXPI CIRCUIT)

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the D14 main body ECU (multiplex network body ECU) connector.


d.

Disconnect the D123 No. 1 semiconductor power integration ECU connector.


e.

Disconnect the G102 No. 2 semiconductor power integration ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D14)Location & Routing

Click Connector(D14)Instrument Panel>Instrument Panel Wire>Main Body ECU

D14-5 (CXP1) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - SEMICONDUCTOR POWER INTEGRATION ECU NO. 2)

NG

5.CHECK HARNESS AND CONNECTOR (CXPI CIRCUIT)
3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - SEMICONDUCTOR POWER INTEGRATION ECU NO. 2)

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the D14 main body ECU (multiplex network body ECU) connector.


d.

Disconnect the G102 No. 2 semiconductor power integration ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D14,G102)Location & Routing

Click Connector(D14)Instrument Panel>Instrument Panel Wire>Main Body ECU

Click Connector(G102)Body>Floor Wire / No. 3 Floor Wire>No. 2 Semiconductor Power Integration ECU

D14-5 (CXP1) - G102-7 (CXPI) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

Pre-procedure1

a.

Disconnect the D14 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the 4A driver side junction block assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition

Click Location & Routing(D14)Location & Routing

Click Connector(D14)Instrument Panel>Instrument Panel Wire>Main Body ECU

D14-5 (CXP1) - 4A-29 Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition

Click Location & Routing(D14)Location & Routing

Click Connector(D14)Instrument Panel>Instrument Panel Wire>Main Body ECU

D14-5 (CXP1) - 4A-30 Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (CXPI CIRCUIT)

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the D14 main body ECU (multiplex network body ECU) connector.


d.

Disconnect the D123 No. 1 semiconductor power integration ECU connector.


e.

Disconnect the G102 No. 2 semiconductor power integration ECU connector.


f.

Disconnect the 4A and 4H driver side junction block assembly connectors.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
4A-29 (CXPI) - Body ground Always 10 kΩ or higher
4A-51 (CXPI) - Body ground Always 10 kΩ or higher
4H-23 (CXPI) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
4A-30 (CXPI) - Body ground Always 10 kΩ or higher
4A-52 (CXPI) - Body ground Always 10 kΩ or higher
4H-32 (CXPI) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (NO. 1 SEMICONDUCTOR POWER INTEGRATION ECU - BATTERY AND BODY GROUND)

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the A59 and D123 No. 1 semiconductor power integration ECU connectors


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D123)Location & Routing

Click Connector(D123)Instrument Panel>Instrument Panel Wire>No. 1 Semiconductor Power Integration ECU

D123-13 (GND1) - Body ground Always Below 1 Ω



b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(A59,D123)Location & Routing

Click Connector(A59)Instrument Panel>Front Compartment Main Wire>No. 1 Semiconductor Power Integration ECU

Click Connector(D123)Instrument Panel>Instrument Panel Wire>No. 1 Semiconductor Power Integration ECU

A59-1 (+B) - Body ground Ignition switch off 8 to 14 V
D123-9 (IG) - Body ground Ignition switch ON 8 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

7.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - NO. 1 SEMICONDUCTOR POWER INTEGRATION ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - NO. 1 SEMICONDUCTOR POWER INTEGRATION ECU)

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the D14 main body ECU (multiplex network body ECU) connector.


d.

Disconnect the D123 No. 1 semiconductor power integration ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D123,D14)Location & Routing

Click Connector(D123)Instrument Panel>Instrument Panel Wire>No. 1 Semiconductor Power Integration ECU

Click Connector(D14)Instrument Panel>Instrument Panel Wire>Main Body ECU

D123-7(CXPI) - D14-5(CXP1) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE NO. 1 SEMICONDUCTOR POWER INTEGRATION ECU

NG

8.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - NO. 1 SEMICONDUCTOR POWER INTEGRATION ECU)
8.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - NO. 1 SEMICONDUCTOR POWER INTEGRATION ECU)

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the D123 No. 1 semiconductor power integration ECU connector.


d.

Disconnect the 4A driver side junction block assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition

Click Location & Routing(D123)Location & Routing

Click Connector(D123)Instrument Panel>Instrument Panel Wire>No. 1 Semiconductor Power Integration ECU

D123-7 (CXPI) - 4A-51 Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition

Click Location & Routing(D123)Location & Routing

Click Connector(D123)Instrument Panel>Instrument Panel Wire>No. 1 Semiconductor Power Integration ECU

D123-7 (CXPI) - 4A-52 Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU - BATTERY AND BODY GROUND)

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the J5 and G102 No. 2 semiconductor power integration ECU connectors.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G102)Location & Routing

Click Connector(G102)Body>Floor Wire / No. 3 Floor Wire>No. 2 Semiconductor Power Integration ECU

G102-6 (GND2) - Body ground Always Below 1 Ω
G102-13 (GND1) - Body ground Always Below 1 Ω



b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(J5,G102)Location & Routing

Click Connector(J5)Body>No. 1 Luggage Room Wire / No. 3 Luggage Room Wire>No. 2 Semiconductor Power Integration ECU

Click Connector(G102)Body>Floor Wire / No. 3 Floor Wire>No. 2 Semiconductor Power Integration ECU

J5-1 (+B) - Body ground Ignition switch off 8 to 14 V
G102-9 (IG) - Body ground Ignition switch ON 8 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

10.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU)

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the D14 main body ECU (multiplex network body ECU) connector.


d.

Disconnect the G102 No. 2 semiconductor power integration ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G102,D14)Location & Routing

Click Connector(G102)Body>Floor Wire / No. 3 Floor Wire>No. 2 Semiconductor Power Integration ECU

Click Connector(D14)Instrument Panel>Instrument Panel Wire>Main Body ECU

G102-7 (CXPI) - D14-5 (CXP1) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU

NG

11.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU)
11.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU)

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the G102 No. 2 semiconductor power integration ECU connector.


d.

Disconnect the 4H driver side junction block assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition

Click Location & Routing(G102)Location & Routing

Click Connector(G102)Body>Floor Wire / No. 3 Floor Wire>No. 2 Semiconductor Power Integration ECU

G102-7 (CXPI) - 4H-23 Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition

Click Location & Routing(G102)Location & Routing

Click Connector(G102)Body>Floor Wire / No. 3 Floor Wire>No. 2 Semiconductor Power Integration ECU

G102-7 (CXPI) - 4H-32 Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

12.CHECK VEHICLE TYPE
12.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ PTC Heater A
w/o PTC Heater B



A

13.CHECK NO.2 SEMICONDUCTOR POWER INTEGRATION ECU

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK NO.2 SEMICONDUCTOR POWER INTEGRATION ECU

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the G102 No. 2 semiconductor power integration ECU connectors.


d.

Turn the ignition switch ON.


Procedure1

a.

Check for pulses according to the value(s) in the table below.

Standard Waveform:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(G102)Location & Routing

Click Connector(G102)Body>Floor Wire / No. 3 Floor Wire>No. 2 Semiconductor Power Integration ECU

G102-7 (CXPI) - Body ground Ignition switch ON Pulse generation


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)