Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM › 2020.11–2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0453477 HYBRID BATTERY SYSTEM J

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  ECU Power Source Circuit  


DESCRIPTION

If the ignition switch is ON, the EV control ECU applies current to the MREL terminal to turn the IGCT No. 2 relay on. This supplies power to the IGCT terminals.

WIRING DIAGRAM

C375135E06
3.667,2.625 5.094,2.979 1.427,0.354 10 false No. 2 EV Battery Pack Wire Connector 3.656,2.448 4.063,2.646 0.406,0.198 10 false G156 5.375,3.156 6.927,3.365 1.552,0.208 10 false Battery ECU Assembly 5.375,2.969 5.719,3.156 0.344,0.188 10 false z26 5.708,1.135 6.323,1.333 0.615,0.198 10 false IGCT 5.698,1.625 6.156,1.823 0.458,0.198 10 false GND 5.708,2.115 6.167,2.313 0.458,0.198 10 false GND1 4.51,1.979 4.969,2.177 0.458,0.198 10 false GND1 4.104,1.979 4.563,2.177 0.458,0.198 10 false GND1 4.563,1.49 5.021,1.688 0.458,0.198 10 false GND 4.125,1.49 4.583,1.688 0.458,0.198 10 false GND 4.552,1 5.167,1.198 0.615,0.198 10 false IGCT 4.125,1.01 4.74,1.208 0.615,0.198 10 false IGCT 2.094,1.323 3.469,1.521 1.375,0.198 10 false IGCT NO. 6 2.604,0.969 2.76,1.167 0.156,0.198 10 false 2 2.198,0.979 2.354,1.177 0.156,0.198 10 false 1 0.208,1.115 2.042,1.313 1.833,0.198 10 false IGCT NO. 2 Relay 5.406,1.469 5.719,1.667 0.313,0.198 10 false 11 5.417,1.969 5.729,2.167 0.313,0.198 10 false 31 5.427,1 5.74,1.198 0.313,0.198 10 false 40 4.958,1.01 5.271,1.208 0.313,0.198 10 false 14 3.875,1.01 4.188,1.208 0.313,0.198 10 false 14 3.885,1.979 4.198,2.177 0.313,0.198 10 false 10 4.979,1.979 5.292,2.177 0.313,0.198 10 false 10 3.927,1.479 4.083,1.677 0.156,0.198 10 false 1 4.99,1.479 5.146,1.677 0.156,0.198 10 false 1

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the FC converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (IGCT VOLTAGE)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the center No. 2 floor to brace extension.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.
C382281N05
2.688,0.25 3.146,0.479 0.458,0.229 2.74,0.281 3.115,0.448 0.375,0.167 10 true G156

Disconnect the G156 No. 2 EV battery pack wire connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the ignition switch to ON.


f.
C373320C13
1.521,0.24 1.99,0.469 0.469,0.229 1.792,1.531 2.896,1.01 true 3.01,0.854 3.375,1.031 0.365,0.177 10 false IGCT 1.583,0.292 2.042,0.49 0.458,0.198 10 false G156 0.115,0.125 0.427,0.281 0.313,0.156 10 false *a
*a Front view of wire harness connector
(No. 2 EV Battery Pack Wire Connector)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(G156)Location & Routing

Click Connector(G156)Body>Floor Wire / No. 3 Floor Wire>EV Supply Battery Assembly

G156-14 (IGCT) - Body ground Ignition switch ON 11 to 14 V


NOTICE:
·

Turning the ignition switch to ON with the service plug grip and FC converter power outlet cable removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the ignition switch is turned to ON with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.




g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

Reconnect the G156 No. 2 EV battery pack wire connector.


j.

Install the center No. 2 floor to brace extension.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (NO. 2 EV BATTERY PACK WIRE CONNECTOR - BODY GROUND)

NG

4.CHECK FUSE (IGCT NO. 6)
2.CHECK HARNESS AND CONNECTOR (NO. 2 EV BATTERY PACK WIRE CONNECTOR - BODY GROUND)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the center No. 2 floor to brace extension.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL


c.
C382281N05
2.688,0.25 3.146,0.479 0.458,0.229 2.74,0.281 3.115,0.448 0.375,0.167 10 true G156

Disconnect the G156 No. 2 EV battery pack wire connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
C374188C20
1.531,0.24 1.969,0.469 0.438,0.229 0.677,1.802 1.208,1.406 true 0.677,0.646 1.177,1.125 true 0.25,0.573 0.865,0.771 0.615,0.198 10 false GND 0.26,1.781 0.875,1.979 0.615,0.198 10 false GND1 1.604,0.292 2.063,0.49 0.458,0.198 10 false G156 0.104,0.125 0.417,0.281 0.313,0.156 10 false *a
*a Front view of wire harness connector
(No. 2 EV Battery Pack Wire Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G156)Location & Routing

Click Connector(G156)Body>Floor Wire / No. 3 Floor Wire>EV Supply Battery Assembly

G156-1 (GND) - Body ground Always Below 1 Ω
G156-10 (GND1) - Body ground Always Below 1 Ω



e.

Reconnect the G156 No. 2 EV battery pack wire connector.


f.

Install the center No. 2 floor to brace extension.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 2 EV BATTERY PACK WIRE CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 2 EV BATTERY PACK WIRE CONNECTOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper No. 1 EV battery cover sub-assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>REMOVAL


c.
C373307N11
2.146,0.125 2.573,0.417 0.427,0.292 2.24,0.177 2.531,0.354 0.292,0.177 10 true z26

Disconnect the z26 battery ECU assembly connector.

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check the terminals of the connector for deformation and corrosion.




d.
C374185C47
1.49,1.604 1.896,1.896 0.406,0.292 1.49,0.052 1.948,0.354 0.458,0.302 1.656,2.604 2.75,1.823 true 2.313,1.073 2.76,1.323 true 0.438,3.031 0.604,2.677 true 2.323,0.844 2.74,0.427 true 0.625,1.979 1.635,2.427 true 0.552,0.75 1.729,1.031 true 1.563,0.146 2.021,0.344 0.458,0.198 10 false G156 1.594,1.698 2.052,1.896 0.458,0.198 10 false z26 0.146,0.104 0.458,0.26 0.313,0.156 10 false *a 0.208,1.573 0.521,1.729 0.313,0.156 10 false *b 0.25,3.083 0.865,3.281 0.615,0.198 10 false IGCT 0.188,0.677 0.802,0.875 0.615,0.198 10 false IGCT 0.292,1.875 0.75,2.073 0.458,0.198 10 false GND 2.833,0.313 3.292,0.51 0.458,0.198 10 false GND 2.844,1.74 3.302,1.938 0.458,0.198 10 false GND1 2.875,1.302 3.333,1.5 0.458,0.198 10 false GND1
*a Front view of wire harness connector
(No. 2 EV Battery Pack Wire Connector)
*b Rear view of wire harness connector
(to Battery ECU Assembly)


Measure the resistance according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z26,G156)Location & Routing

Click Connector(z26)Body>other>EV Supply Battery Assembly , Battery ECU Assembly

Click Connector(G156)Body>Floor Wire / No. 3 Floor Wire>EV Supply Battery Assembly

z26-40 (IGCT) - G156-14 (IGCT) Always Below 1 Ω
z26-11 (GND) - G156-1 (GND) Always Below 1 Ω
z26-31 (GND1) - G156-10 (GND1) Always Below 1 Ω
z26-40 (IGCT) or G156-14 (IGCT) - Body ground and other terminals Always 10 kΩ or higher
z26-11 (GND) or G156-1 (GND) - Body ground and other terminals Always 10 kΩ or higher
z26-31 (GND1) or G156-10 (GND1) - Body ground and other terminals Always 10 kΩ or higher



e.

Reconnect the z26 battery ECU assembly connector.


f.

Install the upper No. 1 EV battery cover sub-assembly.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK FUSE (IGCT NO. 6)
a.
A480744C01
2.948,2.01 2.49,0.74 true 0.156,0.854 0.469,1.052 0.313,0.198 10 false *1 2.396,0.521 2.708,0.719 0.313,0.198 10 false *a
*1 Luggage Room Relay Block Assembly
*a IGCT NO. 6 Fuse


Remove the IGCT NO. 6 fuse from the luggage room relay block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IGCT NO. 6 fuse terminals 1 - 2 Always Below 1 Ω



c.

Install the IGCT NO. 6 fuse to the luggage room relay block assembly.


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (NO. 2 EV BATTERY PACK WIRE CONNECTOR - LUGGAGE ROOM RELAY BLOCK ASSEMBLY)

NG

7.CHECK HARNESS AND CONNECTOR (NO. 2 EV BATTERY PACK WIRE CONNECTOR - LUGGAGE ROOM RELAY BLOCK ASSEMBLY)
5.CHECK HARNESS AND CONNECTOR (NO. 2 EV BATTERY PACK WIRE CONNECTOR - LUGGAGE ROOM RELAY BLOCK ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the center No. 2 floor to brace extension.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL


c.
C382281N05
2.688,0.25 3.146,0.479 0.458,0.229 2.74,0.281 3.115,0.448 0.375,0.167 10 true G156

Disconnect the G156 No. 2 EV battery pack wire connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Remove the IGCT NO. 6 fuse from the luggage room relay block assembly.


e.

Measure the resistance according to the value(s) in the table below.

A480745C01
5.115,0.521 5.573,0.792 0.458,0.271 5.115,2.198 5.365,1.719 true 0.719,0.917 1.031,1.115 0.313,0.198 10 false *1 2.802,0.208 3.115,0.406 0.313,0.198 10 false *a 4.448,0.344 4.76,0.542 0.313,0.198 10 false *b 5.177,0.594 5.729,0.792 0.552,0.198 10 false G156 4.948,2.24 5.5,2.438 0.552,0.198 10 false IGCT
*1 Luggage Room Relay Block Assembly - -
*a IGCT NO. 6 Fuse Holder *b Front view of wire harness connector
(No. 2 EV Battery Pack Wire Connector)


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G156)Location & Routing

Click Connector(G156)Body>Floor Wire / No. 3 Floor Wire>EV Supply Battery Assembly

G156-14 (IGCT) - 2 (IGCT NO. 6 fuse holder) Always Below 1 Ω



f.

Install the IGCT NO. 6 fuse to the luggage room relay block assembly.


g.

Reconnect the G156 No. 2 EV battery pack wire connector.


h.

Install the center No. 2 floor to brace extension.


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (LUGGAGE ROOM RELAY BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (LUGGAGE ROOM RELAY BLOCK ASSEMBLY)
a.

Remove the IGCT NO. 6 fuse from the luggage room relay block assembly.


b.

Remove the IGCT NO. 2 relay from the luggage room relay block assembly.


c.
A480746C01
0.844,0.177 1.156,0.375 0.313,0.198 10 false *b 2.25,0.177 2.563,0.375 0.313,0.198 10 false *a 0.125,1.208 0.438,1.406 0.313,0.198 10 false *1
*1 Luggage Room Relay Block Assembly
*a IGCT NO. 6 Fuse Holder
*b IGCT NO. 2 Relay Holder


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (IGCT NO. 2 relay holder) - 1 (IGCT NO. 6 fuse holder) Always Below 1 Ω



d.

Install the IGCT NO. 2 relay from the luggage room relay block assembly.


e.

Install the IGCT NO. 6 fuse from the luggage room relay block assembly.


Result:
Proceed to
OK
NG



OK

CHECK ECU Power Source Circuit (HYBRID CONTROL SYSTEM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (NO. 2 EV BATTERY PACK WIRE CONNECTOR - LUGGAGE ROOM RELAY BLOCK ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the center No. 2 floor to brace extension.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL


c.
C382281N05
2.688,0.25 3.146,0.479 0.458,0.229 2.74,0.281 3.115,0.448 0.375,0.167 10 true G156

Disconnect the G156 No. 2 EV battery pack wire connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Remove the IGCT NO. 6 fuse from the luggage room relay block assembly.


e.

Measure the resistance according to the value(s) in the table below.

A480745C01
5.115,0.521 5.573,0.792 0.458,0.271 5.115,2.198 5.365,1.719 true 0.719,0.917 1.031,1.115 0.313,0.198 10 false *1 2.802,0.208 3.115,0.406 0.313,0.198 10 false *a 4.448,0.344 4.76,0.542 0.313,0.198 10 false *b 5.177,0.594 5.729,0.792 0.552,0.198 10 false G156 4.948,2.24 5.5,2.438 0.552,0.198 10 false IGCT
*1 Luggage Room Relay Block Assembly - -
*a IGCT NO. 6 Fuse Holder *b Front view of wire harness connector
(No. 2 EV Battery Pack Wire Connector)


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G156)Location & Routing

Click Connector(G156)Body>Floor Wire / No. 3 Floor Wire>EV Supply Battery Assembly

G156-14 (IGCT) or 2 (IGCT NO. 6 fuse holder) - Body ground and other terminals Always 10 kΩ or higher



f.

Install the IGCT NO. 6 fuse to the luggage room relay block assembly.


g.

Reconnect the G156 No. 2 EV battery pack wire connector.


h.

Install the center No. 2 floor to brace extension.


Result:
Proceed to
OK
NG



OK

REPLACE FUSE (IGCT NO. 6)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (IGCT NO. 6)