Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HV BATTERY › 2020.11–2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0457184 HV BATTERY A

HYBRID / BATTERY CONTROL  HV BATTERY  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A479058N08
6.417,0.167 6.917,0.167 false 1.698,0.813 2.146,0.813 false 5.969,0.021 6.583,0.469 0.615,0.448 18 false 1, 2 1.49,0.688 1.865,1.125 0.375,0.438 18 false 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 READ VALUE USING GTS - (Click here) - -
3 SERVICE PLUG GRIP G3834 - - -

A481588N05
5.24,1.781 6.323,2.01 1.083,0.229 0.958,1.844 0.958,1.271 false 2.646,2.708 2.646,2.135 false 4.885,2.531 5.167,2.417 5.167,2.417 5.417,2.417 false 6.51,0.219 6.833,0.219 false 4.563,2.063 4.563,1.896 4.563,1.896 5.229,1.896 false 4.865,2.063 4.865,1.896 false 2.396,4.969 4.979,4.969 true 2.188,4.854 2.469,5.208 0.281,0.354 18 false 6 2.573,2.771 2.854,3.125 0.281,0.354 18 false 4 0.875,1.938 1.156,2.292 0.281,0.354 18 false 5 4.083,0.969 4.365,1.323 0.281,0.354 10 false x 6 5.531,3.115 5.813,3.469 0.281,0.354 10 false x 2 5.75,2.302 6.302,2.677 0.552,0.375 18 false 7, 9 6.26,0.115 6.542,0.469 0.281,0.354 18 false 8 5.333,1.833 6.448,2.073 1.115,0.24 8 false 8.0 (82, 71 in.*lbf)

Procedure Part Name Code
Z101186

Z101188

Z101187

4 UPPER RADIATOR SUPPORT SEAL 53292A - - -
5 FC STACK COVER SUB-ASSEMBLY 1A906 - - -
6 FC CONVERTER POWER OUTLET CABLE (INVERTER WITH CONVERTER ASSEMBLY) G9200A (Click here) - -
7 REMOVE CONNECTOR COVER ASSEMBLY - (Click here) - -
8 CHECK TERMINAL VOLTAGE - (Click here) - -
9 INSTALL CONNECTOR COVER ASSEMBLY - (Click here) - -

V100146

N*m (kgf*cm, ft.*lbf): Specified torque - -

A478427N19
1.167,1.615 1.677,1.615 false 1.323,2.917 1.323,3.219 false 6.292,3.885 6.292,4.188 false 4.344,3.323 4.344,3.625 false 1.031,4.813 1.031,5.115 false 4.792,4.438 5.302,4.438 false 6.104,5.115 6.104,5.344 false 5.375,4.313 5.938,4.698 0.563,0.385 18 false 12 4.198,3.667 4.573,4.021 0.375,0.354 18 false 10 3.156,0.26 3.469,0.458 0.313,0.198 10 false x 2 1.604,3.729 1.917,3.927 0.313,0.198 10 false x 2 5.917,1.698 6.229,1.896 0.313,0.198 10 false x 2 4.125,1.813 4.438,2.01 0.313,0.198 10 false x 5 5.958,5.385 6.313,5.708 0.354,0.323 18 false 14 0.885,5.156 1.24,5.479 0.354,0.323 18 false 15 6.135,4.208 6.49,4.531 0.354,0.323 18 false 16 1.198,3.25 1.573,3.604 0.375,0.354 18 false 11 0.792,1.521 1.146,1.844 0.354,0.323 18 false 13

Procedure Part Name Code
Z101186

Z101188

Z101187

10 LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY 64701 - - -
11 LUGGAGE COMPARTMENT TRIM COVER LH 64715D - - -
12 TOOL BOX 75201A - - -
13 FRONT LUGGAGE COMPARTMENT TRIM COVER 64075B - - -
14 REAR FLOOR FINISH PLATE 58387 - - -
15 LUGGAGE COMPARTMENT TRIM COVER INNER LH 64722 - - -
16 LUGGAGE COMPARTMENT TRIM COVER INNER RH 64721 - - -

A480488N05
5.365,4.385 5.927,4.385 false 4.219,5.198 4.781,5.198 false 1.469,2.104 2.031,2.104 false 0.917,3.448 0.917,3.948 false 3.75,2.75 3.75,3.417 false 4,0.833 4.563,0.833 false 5.333,3.333 5.729,2.917 5.729,2.917 5.896,2.917 false 1.885,4.865 1.563,5.344 1.563,5.344 1.354,5.344 false 2.729,2.167 3.167,2.677 0.438,0.51 10 false x 4 4.729,3.042 5.167,3.552 0.438,0.51 10 false x 4 0.792,4.01 1.344,4.365 0.552,0.354 18 false 17 3.875,5.094 4.427,5.448 0.552,0.354 18 false 18 3.688,0.708 4.24,1.063 0.552,0.354 18 false 19 1.146,1.99 1.698,2.344 0.552,0.354 18 false 20 1,5.208 1.552,5.563 0.552,0.354 18 false 22 5.042,4.281 5.594,4.635 0.552,0.354 18 false 21 3.615,3.49 4.167,3.844 0.552,0.354 18 false 23 5.99,2.781 6.542,3.135 0.552,0.354 18 false 24

Procedure Part Name Code
Z101186

Z101188

Z101187

17 REAR DOOR SCUFF PLATE INSIDE RH 67917F - - -
18 REAR DOOR SCUFF PLATE INSIDE LH 67918F - - -
19 BENCH TYPE REAR SEATBACK ASSEMBLY - - - -
20 REAR SEAT SIDE GARNISH RH 62551F - - -
21 REAR SEAT SIDE GARNISH LH 62552F - - -
22 NO. 1 ROOM PARTITION PAD 64273D - - -
23 NO. 2 EV BATTERY INTAKE DUCT G92D2A - - -
24 NO. 4 EV BATTERY INTAKE DUCT G92D4A - - -

A477110N06
0.823,1.604 0.99,1.604 0.99,1.604 1.177,1.26 false 1.781,2 1.896,2 1.896,2 2,1.365 false 2.698,2.292 2.844,2.292 2.844,2.292 2.927,1.688 false 4.021,3.417 4.188,3.417 4.188,3.417 4.375,3.073 false 5.844,2.417 6.01,2.417 6.01,2.417 6.208,2.906 false 4.583,0.26 4.667,0.26 4.667,0.26 5.01,0.688 false 3.177,0.635 3.26,0.635 3.26,0.635 3.604,1.063 false 5.396,3.542 5.646,3.542 5.646,3.542 5.396,3.104 false 2.365,1.354 2.677,1.552 0.313,0.198 10 false x 2 0.677,0.76 0.99,0.958 0.313,0.198 10 false x 3 3.854,2.583 4.167,2.781 0.313,0.198 10 false x 2 5.063,3.406 5.615,3.76 0.552,0.354 18 false 26 5.51,2.281 6.063,2.635 0.552,0.354 18 false 27 0.49,1.49 1.042,1.844 0.552,0.354 18 false 28 1.458,1.854 2.01,2.208 0.552,0.354 18 false 29 2.396,2.167 2.948,2.521 0.552,0.354 18 false 30 4.281,0.146 4.833,0.5 0.552,0.354 18 false 31 2.854,0.5 3.406,0.854 0.552,0.354 18 false 32 3.708,3.281 4.26,3.635 0.552,0.354 18 false 25

Procedure Part Name Code
Z101186

Z101188

Z101187

25 CENTER NO. 2 FLOOR TO BRACE EXTENSION 64228A - - -
26 NO. 2 EV BATTERY CLAMP COVER G92P6A (Click here) - -
27 FLOOR WIRE 82161 (Click here) - -
28 CENTER NO. 1 FLOOR TO BLACE EXTENSION 64227A - - -
29 BATTERY COVER LOCK STRIKER G9295B (Click here) - -
30 NO. 10 EV BATTERY SHIELD PANEL G92QCA (Click here) - -
31 FLOOR UNDER WIRE 821H1 (Click here) - -
32 NO. 4 EV BATTERY EXHAUST DUCT G92F4A - - -

A483335N01
5.115,2.365 5.115,2.146 false 6.208,2.208 6.208,1.865 false 5.25,3.521 5.896,3.521 false 4.979,2.396 5.531,2.75 0.552,0.354 18 false 33 6.094,2.24 6.646,2.594 0.552,0.354 18 false 34 4.917,3.396 5.469,3.75 0.552,0.354 18 false 35 5.073,1.063 5.531,1.26 0.458,0.198 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

33 STEREO COMPONENT AMPLIFIER ASSEMBLY WITH BRACKET - - - -
34 CLEARANCE WARNING ECU ASSEMBLY 89340A - - -
35 NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY 899A0B (Click here) - -

A483336N01
1.875,1.344 1.625,0.719 1.625,0.719 1.323,0.719 false 6.104,2.385 5.844,2.385 5.844,2.385 5.604,1.875 false 5.458,5.219 5.115,5.219 5.115,5.219 4.448,4.76 false 6.448,2.24 7,2.594 0.552,0.354 18 false 37 1,0.604 1.552,0.958 0.552,0.354 18 false 37 5.781,5.094 6.333,5.448 0.552,0.354 18 false 36 4.042,3.833 4.5,4.031 0.458,0.198 10 false x 4

Procedure Part Name Code
Z101186

Z101188

Z101187

36 NO. 1 LUGGAGE ROOM WIRE 82181 (Click here) - -
37 FLOOR WIRE 82161 (Click here) - -

A483337N01
2.083,3 2.333,3 2.333,3 2.5,2.5 false 4.906,3.24 4.74,3.24 4.74,3.24 4.625,2.729 false 4.781,0.458 4.573,0.458 4.573,0.458 4.292,1.167 false 5.25,3.125 5.813,3.469 0.563,0.344 18 false 38 5.146,0.344 5.708,0.688 0.563,0.344 18 false 39 1.708,2.844 2.271,3.188 0.563,0.344 18 false 40 2.365,0.938 2.823,1.135 0.458,0.198 10 false x 3 4.75,1.146 5.208,1.344 0.458,0.198 10 false x 2 5.052,2.104 5.51,2.302 0.458,0.198 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

38 EV BATTERY BRACKET LH G928BA (Click here) - -
39 EV BATTERY BRACKET RH G928AA (Click here) - -
40 EV SUPPLY BATTERY ASSEMBLY G9510B (Click here) - -

A481438N03
1.042,0.875 1.698,0.875 false 1.115,3.313 1.219,3.313 1.219,3.313 1.563,2.854 false 6.375,0.333 6.698,0.333 false 0.719,0.771 1.271,1.125 0.552,0.354 18 false 41 1.031,1.917 1.385,2.115 0.354,0.198 10 false x 4 6.031,0.219 6.583,0.573 0.552,0.354 18 false 43 0.781,3.188 1.333,3.542 0.552,0.354 18 false 42

Procedure Part Name Code
Z101186

Z101188

Z101187

41 EV BATTERY DUCT SUB-ASSEMBLY G9209C (Click here) - -
42 NO. 9 EV BATTERY SHIELD PANEL G92QBA (Click here) - -
43 PERFORM RECOVERY INSPECTION - (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during EV supply battery assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
EV supply battery assembly
·

Prediagnostic battery charge

·

Battery diagnosis

·

Battery status info update


Warning light illumination (Click here)

CAUTION:
·
A340386


·

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system


·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -


When disposing of an EV supply battery assembly, make sure to return it through an authorized collection agent who is capable of handling it safely. If the EV supply battery assembly is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

If the EV battery has been struck or dropped, replace it.

·

When connecting a connector to the EV battery, confirm that the connector is securely connected through the following:

- Push the connector until a click sound is heard.

- Visually check and confirm that the connector is securely connected by pulling on it.

·

Make sure to insulate the high-voltage connectors and terminals of the EV battery with insulating tape after removing it.

If the EV battery stored without insulating the connectors and terminals, electric shock or fire may result.

·

When performing repairs around the EV battery, such as using a tap, do not allow metal shavings to enter the EV battery.

·

Do not touch any high voltage wire harnesses, connectors or parts with bare hands.

·
C357364C01
0.833,3.083 0.833,3.25 0.833,3.25 2.75,3.25 false 1.333,3.25 1.333,3.083 false 2.104,3.25 2.104,3.083 false 2.604,3.25 2.604,3.083 false 2.833,3.167 3,3.333 0.167,0.167 10 false *1
*1 No. 1 EV Battery Carrier Sheet


Hold the areas shown in the illustration and lift the EV battery.

·

Do not break the No. 1 EV battery carrier sheet.

·

Do not allow foreign matter, such as grease or oil, to adhere to the bolts or nuts of the EV battery.

·

Do not put your hands into the openings of the EV battery.

·

When removing/installing/moving the EV battery assembly, make sure not to tilt it more than 80°.

·

Do not climb on top of or stand on the EV battery.

·

Do not allow any foreign matter or water to enter the EV battery.

·

If any bolts, nuts or clips are dropped into the EV battery, make sure to remove them.



Hide 2. READ VALUE USING GTS

a.
A461168N05
0.5,0.094 0.781,0.448 0.281,0.354 18 false i

i.

Read the Data List.

Powertrain > EV Battery > Data List
Tester Display
Hybrid/EV Battery Temperature 1
Hybrid/EV Battery Temperature 2
Hybrid/EV Battery Temperature 3
Hybrid/EV Battery Temperature 4
Hybrid/EV Battery Temperature 5
Hybrid/EV Battery Temperature 6
50003 398 62,63,64,65,66,67
NOTICE:

If any of the temperatures listed in "Hybrid/EV Battery Temperature 1 to 6" are 50°C or more, leave the vehicle until the temperature drops to less than 50°C.




Hide 53292A 4.REMOVE UPPER RADIATOR SUPPORT SEAL

Hide 1A906 5.REMOVE FC STACK COVER SUB-ASSEMBLY

Hide G9200A 6.DISCONNECT FC CONVERTER POWER OUTLET CABLE (INVERTER WITH CONVERTER ASSEMBLY)

Z101186

Click here(Click here)

Hide 7.REMOVE CONNECTOR COVER ASSEMBLY

Z101186

Click here(Click here)

Hide 8.CHECK TERMINAL VOLTAGE

Z101186

Click here(Click here)

Hide 9.INSTALL CONNECTOR COVER ASSEMBLY

Z101186

Click here(Click here)

Hide 64701 10.REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

Hide 64715D 11.REMOVE LUGGAGE COMPARTMENT TRIM COVER LH

Hide 64075B 13.REMOVE FRONT LUGGAGE COMPARTMENT TRIM COVER

Hide 58387 14.REMOVE REAR FLOOR FINISH PLATE

Hide 64722 15.REMOVE LUGGAGE COMPARTMENT TRIM COVER INNER LH

Hide 64721 16.REMOVE LUGGAGE COMPARTMENT TRIM COVER INNER RH

Hide 67917F 17.REMOVE REAR DOOR SCUFF PLATE INSIDE RH

Hide 67918F 18.REMOVE REAR DOOR SCUFF PLATE INSIDE LH

Hide 19.REMOVE BENCH TYPE REAR SEATBACK ASSEMBLY

Hide 62551F 20.REMOVE REAR SEAT SIDE GARNISH RH

Hide 62552F 21.REMOVE REAR SEAT SIDE GARNISH LH

Hide 64273D 22.REMOVE NO. 1 ROOM PARTITION PAD

Hide G92D2A 23.REMOVE NO. 2 EV BATTERY INTAKE DUCT

a.
A477146


Hide G92D4A 24.REMOVE NO. 4 EV BATTERY INTAKE DUCT

a.
A477145


Hide 64228A 25.REMOVE CENTER NO. 2 FLOOR TO BRACE EXTENSION

a.
A477149


Hide G92P6A 26.REMOVE NO. 2 EV BATTERY CLAMP COVER

Z101186

CAUTION:

Wear insulated gloves.



a.
A477150


Hide 82161 27.DISCONNECT FLOOR WIRE

Z101186

CAUTION:

Wear insulated gloves.



a.
A480476


Hide 64227A 28.REMOVE CENTER NO. 1 FLOOR TO BRACE EXTENSION

a.
A477152


Hide G9295B 29.REMOVE BATTERY COVER LOCK STRIKER

Z101186

CAUTION:

Wear insulated gloves.



a.
A477147C02
4.531,0.229 4.583,0.146 4.583,0.146 4.667,0.146 false 4,0.75 4.167,0.75 4.167,0.75 4.323,0.625 false 4.365,0.969 4.469,0.833 4.469,0.833 4.594,0.833 true 4.521,1.073 4.74,1.073 false 4.719,0.094 5.031,0.292 0.313,0.198 10 false *1 3.823,0.708 4.135,0.906 0.313,0.198 10 false *a 3.802,0.406 4.115,0.604 0.313,0.198 10 false *b 4.646,0.771 4.958,0.969 0.313,0.198 10 false *c 4.792,1.021 5.104,1.219 0.313,0.198 10 false *2 2.24,0.083 2.469,0.427 0.229,0.344 18 true i
*1 Service Plug Grip *2 Battery Cover Lock Striker
*a Projection *b Turn
*c Button - -


i.

Using the service plug grip, remove the battery cover lock striker.

HINT:

Insert the projection of the service plug grip and turn the button of the battery cover lock striker counterclockwise to release the lock.




Hide G92QCA 30.REMOVE NO. 10 EV BATTERY SHIELD PANEL

Z101186

CAUTION:

Wear insulated gloves.



a.
A480477


Hide 821H1 31.DISCONNECT FLOOR UNDER WIRE

Z101186

CAUTION:

Wear insulated gloves.



a.
A477154


Hide G92F4A 32.REMOVE NO. 4 EV BATTERY EXHAUST DUCT

a.
A477157


Hide 33.REMOVE STEREO COMPONENT AMPLIFIER ASSEMBLY WITH BRACKET

Hide 89340A 34.REMOVE CLEARANCE WARNING ECU ASSEMBLY

Hide 899A0B 35.REMOVE NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY

Z101186

Click here(Click here)

Hide 82181 36.REMOVE NO. 1 LUGGAGE ROOM WIRE

Z101186

HINT:

Place the disconnected No. 1 luggage room wire at the side of the vehicle to prevent the wire harness from being pinched when removing and reinstalling the EV supply battery assembly.



a.
A483338


b.
A483339


Hide 82161 37.REMOVE FLOOR WIRE

Z101186

HINT:

Place the disconnected floor wire at the side of the vehicle to prevent the wire harness from being pinched when removing and reinstalling the EV supply battery assembly.



a.
A478057


b.
A483340


Hide G928BA 38.REMOVE EV BATTERY BRACKET LH

Z101186

CAUTION:

Wear insulated gloves.



a.
A477161


Hide G928AA 39.REMOVE EV BATTERY BRACKET RH

Z101186

CAUTION:

Wear insulated gloves.



a.
A480353


Hide G9510B 40.REMOVE EV SUPPLY BATTERY ASSEMBLY

Z101186

CAUTION:

Wear insulated gloves.



a.
A477155N02
0.417,0.052 0.656,0.344 0.24,0.292 18 true i 4.094,0.052 4.333,0.344 0.24,0.292 18 true ii

i.

Remove the 3 bolts.

NOTICE:

Do not allow foreign matter, such as grease or oil, to adhere to the bolts of the EV supply battery assembly.



ii.

Place wooden blocks as shown in the illustration and remove the EV supply battery assembly by sliding it on the wooden blocks.

NOTICE:
·

To prevent the wire harness from being caught, make sure to bundle the wire harness using insulating tape or equivalent.

·

Since the EV supply battery assembly is very heavy, 2 people are needed to remove it. When removing the EV supply battery assembly, be careful not to damage the parts around it.

·

When removing the EV supply battery assembly from the vehicle, do not allow it to contact the vehicle.

·

When removing/installing/moving the EV supply battery assembly, make sure not to tilt it more than 80°.

·

Insulate the disconnected terminals or connectors with insulating tape.

·

If the EV supply battery assembly has been struck or dropped, replace it.





Hide G9209C 41.REMOVE EV BATTERY DUCT SUB-ASSEMBLY

Z101186

CAUTION:

Wear insulated gloves.



a.
A477160


Hide G92QBA 42.REMOVE NO. 9 EV BATTERY SHIELD PANEL

Z101186

CAUTION:

Wear insulated gloves.



a.
A477159


Hide 43.PERFORM RECOVERY INSPECTION

Z101186

NOTICE:

Before returning the EV supply battery assembly, make sure to perform a recovery inspection.

Click here(Click here)