Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM
RM37H0E _56 Audio / Visual / Telematics _095293 PARK ASSIST / MONITORING _0455115 PANORAMIC VIEW MONITOR SYSTEM J

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  Infrared light does not Turn ON at Low Illumination Time  


DESCRIPTION

The parking assist ECU illuminates the parking assist light at night or other times when the light level is low to enable image recognition.

WIRING DIAGRAM

E439850E02
5.927,5.552 6.865,5.917 0.938,0.365 10 false Parking Assist ECU 0.417,8.292 2.75,8.469 2.333,0.177 10 false Outer Rear View Mirror Assembly RH 3.24,6.302 3.604,6.49 0.365,0.188 10 false BTR 3.24,5.917 3.635,6.104 0.396,0.188 10 false GTR 3.24,6.688 3.625,6.854 0.385,0.167 10 false GND 3.24,7.063 3.469,7.25 0.229,0.188 10 false +B 3.24,7.677 4.906,7.885 1.667,0.208 10 false Light Parking Assist Circuit 1.698,6.594 2.083,6.813 0.385,0.219 10 false GND 1.729,6.208 2.052,6.427 0.323,0.219 10 false BTR 1.708,5.823 2.042,6.042 0.333,0.219 10 false GTR 1.802,6.979 2.021,7.188 0.219,0.208 10 false +B 3.542,1.24 3.99,1.438 0.448,0.198 10 false NV IR 2.427,1.083 3.323,1.271 0.896,0.188 10 false R/B-IG1 NO.2 0.635,7.573 1.917,7.948 1.281,0.375 10 false Parking Assist Light RH 3.958,2.646 4.167,2.844 0.208,0.198 10 false IG 5.906,0.5 6.323,0.688 0.417,0.188 10 false IRSW 0.563,0.469 1.5,0.667 0.938,0.198 10 false from IG1 Relay 0.604,3.854 0.76,4.031 0.156,0.177 10 false A 0.635,7.427 0.781,7.625 0.146,0.198 10 false B 0.406,4.667 0.708,4.854 0.302,0.188 10 false E30 0.417,8.125 0.771,8.302 0.354,0.177 10 false E12 3.219,7.51 3.521,7.667 0.302,0.156 10 false D21 5.917,5.406 6.229,5.594 0.313,0.188 10 false G13 3.813,4.781 4.156,4.948 0.344,0.167 10 false GND 3.25,2.427 3.854,2.667 0.604,0.24 10 false GTL 3.271,2.802 3.875,3.042 0.604,0.24 10 false BTL 3.271,3.198 3.875,3.438 0.604,0.24 10 false GND 3.271,3.583 3.875,3.823 0.604,0.24 10 false +B 1.729,2.292 2.073,2.49 0.344,0.198 10 false GTL 1.74,2.688 2.042,2.885 0.302,0.198 10 false BTL 1.708,3.063 2.063,3.26 0.354,0.198 10 false GND 1.802,3.448 2.073,3.646 0.271,0.198 10 false +B 1.135,5.885 1.427,6.094 0.292,0.208 10 false TH- 1.063,2.354 1.344,2.552 0.281,0.198 10 false TH- 1.115,6.313 1.448,6.51 0.333,0.198 10 false TH+ 1.031,2.75 1.354,2.927 0.323,0.177 10 false TH+ 0.906,3.135 1.354,3.344 0.448,0.208 10 false LEDL- 0.948,6.667 1.417,6.875 0.469,0.208 10 false LEDR- 0.885,3.521 1.365,3.719 0.479,0.198 10 false LEDL+ 0.938,7.052 1.427,7.271 0.49,0.219 10 false LEDR+ 3.281,0.438 3.438,0.635 0.156,0.198 10 false 1 3.281,0.844 3.438,1.042 0.156,0.198 10 false 5 4.052,0.844 4.208,1.042 0.156,0.198 10 false 3 4.052,0.448 4.208,0.646 0.156,0.198 10 false 2 3.052,2.302 3.208,2.5 0.156,0.198 10 false 2 3.052,2.708 3.208,2.906 0.156,0.198 10 false 3 1.406,2.688 1.563,2.885 0.156,0.198 10 false 2 1.417,3.063 1.573,3.26 0.156,0.198 10 false 3 1.49,6.615 1.646,6.813 0.156,0.198 10 false 3 1.49,6.219 1.646,6.417 0.156,0.198 10 false 2 1.406,2.292 1.563,2.49 0.156,0.198 10 false 1 1.479,5.844 1.635,6.042 0.156,0.198 10 false 1 5.677,0.427 5.833,0.625 0.156,0.198 10 false 8 3.042,6.979 3.198,7.177 0.156,0.198 10 false 8 1.49,6.99 1.646,7.188 0.156,0.198 10 false 4 1.406,3.458 1.563,3.656 0.156,0.198 10 false 4 2.104,2.292 2.26,2.49 0.156,0.198 10 false 4 2.115,5.833 2.271,6.031 0.156,0.198 10 false 4 2.115,3.438 2.281,3.625 0.167,0.188 10 false 1 2.115,6.969 2.26,7.156 0.146,0.188 10 false 1 2.115,2.667 2.302,2.875 0.188,0.208 10 false 3 2.125,3.063 2.281,3.26 0.156,0.198 10 false 2 2.115,6.594 2.271,6.792 0.156,0.198 10 false 2 2.115,6.219 2.26,6.396 0.146,0.177 10 false 3 2.969,6.208 3.208,6.406 0.24,0.198 10 false 12 2.969,5.833 3.208,6.031 0.24,0.198 10 false 11 3.042,3.479 3.198,3.677 0.156,0.198 10 false 6 4.208,2.573 4.365,2.771 0.156,0.198 10 false 4 4.208,4.708 4.427,4.896 0.219,0.188 10 false 10 3.052,6.604 3.208,6.802 0.156,0.198 10 false 9 3.052,3.094 3.208,3.292 0.156,0.198 10 false 7 2.417,0.667 3.302,0.958 0.885,0.292 10 false R/B-IG1 NO.2 0.406,4.823 2.708,5.042 2.302,0.219 10 false Outer Rear View Mirror Assembly LH 0.594,4.021 1.844,4.375 1.25,0.354 10 false Parking Assist Light LH 0.583,0.885 1.542,1.094 0.958,0.208 10 false from IG1 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the parking assist ECU after the auxiliary battery terminal has been disconnected, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION

·

Inspect the fuse for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK LIGHT PARKING ASSIST CIRCUIT (POWER SOURCE AND BODY GROUND)
a.

Disconnect the light parking assist circuit connector.


b.

Enter the following menus: Body Electrical / Clearance Warning / Utility.

Chassis > Circumference Monitoring Camera Control Module > Utility
Tester Display
IR Projector Inspection
50005 470 4641

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D21)Location & Routing

Click Connector(D21)Instrument Panel>Instrument Panel Wire>Light Parking Assist Circuit

D21-10 (GND) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D21)Location & Routing

Click Connector(D21)Instrument Panel>Instrument Panel Wire>Light Parking Assist Circuit

D21-4 (IG) - Body ground IR Emitter Illumination Trigger OFF Below 1 V
D21-4 (IG) - Body ground IR Emitter Illumination Trigger ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK LIGHT PARKING ASSIST CIRCUIT OPERATION

NG

17.INSPECT IR RELAY
2.CHECK LIGHT PARKING ASSIST CIRCUIT OPERATION
a.

Enter the following menus: Chassis / Clearance Warning / Utility.

Chassis > Circumference Monitoring Camera Control Module > Utility
Tester Display
IR Projector Inspection
50005 470 4641

b.

Cover the bottom of the outer rear view mirror assembly with your hand or a cloth.


c.

According to the display on the GTS, illuminate the parking assist light and check for changes in the multi-display screen display.

HINT:
·

When the parking assist light illuminates, the multi-display screen display will appear to be illuminated by a purplish light.

·

It is necessary to turn the ignition switch off once to illuminate the parking assist light again.




Result:
Result Proceed to
All parking assist lights do not illuminate A
Parking assist light on the left side only does not illuminate B
Parking assist light on the right side only does not illuminate C
All illuminate D



A

3.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH - LIGHT PARKING ASSIST CIRCUIT)

B

9.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH - LIGHT PARKING ASSIST CIRCUIT)

C

13.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY RH - LIGHT PARKING ASSIST CIRCUIT)

D

3.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH - LIGHT PARKING ASSIST CIRCUIT)
a.

Disconnect the D21 light parking assist circuit connector.


b.

Disconnect the E30 outer rear view mirror assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D21,E30)Location & Routing

Click Connector(D21)Instrument Panel>Instrument Panel Wire>Light Parking Assist Circuit

Click Connector(E30)Body>Front Door Wire LH / Front Door Wire RH>Outer Rear View Mirror Assembly LH

D21-2 (GTL) - E30-4 (GTL) Always Below 1 Ω
D21-3 (BTL) - E30-3 (BTL) Always Below 1 Ω
D21-6 (+B) - E30-1 (+B) Always Below 1 Ω
D21-7 (GND) - E30-2 (GND) Always Below 1 Ω
D21-2 (GTL) or E30-4 (GTL) - Body ground Always 10 kΩ or higher
D21-3 (BTL) or E30-3 (BTL) - Body ground Always 10 kΩ or higher
D21-6 (+B) or E30-1 (+B) - Body ground Always 10 kΩ or higher
D21-7 (GND) or E30-2 (GND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK OUTER REAR VIEW MIRROR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK OUTER REAR VIEW MIRROR ASSEMBLY LH
a.

Disconnect the parking assist light LH connector.


b.

Disconnect the E30 outer rear view mirror assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(E30)Location & Routing

Click Connector(E30)Body>Front Door Wire LH / Front Door Wire RH>Outer Rear View Mirror Assembly LH

A-1 (TH-) - E30-4 (GTL) Always Below 1 Ω
A-2 (TH+) - E30-3 (BTL) Always Below 1 Ω
A-3 (LEDL-) - E30-2 (GND) Always Below 1 Ω
A-4 (LEDL+) - E30-1 (+B) Always Below 1 Ω
A-1 (TH-) or E30-4 (GTL) - Body ground Always 10 kΩ or higher
A-2 (TH+) or E30-3 (BTL) - Body ground Always 10 kΩ or higher
A-3 (LEDL-) or E30-2 (GND) - Body ground Always 10 kΩ or higher
A-4 (LEDL+) or E30-1 (+B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY RH - LIGHT PARKING ASSIST CIRCUIT)

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

5.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY RH - LIGHT PARKING ASSIST CIRCUIT)
a.

Disconnect the D21 light parking assist circuit connector.


b.

Disconnect the E12 outer rear view mirror assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D21,E12)Location & Routing

Click Connector(D21)Instrument Panel>Instrument Panel Wire>Light Parking Assist Circuit

Click Connector(E12)Body>Front Door Wire LH / Front Door Wire RH>Outer Rear View Mirror Assembly RH

D21-11 (GTR) - E12-4 (GTR) Always Below 1 Ω
D21-12 (BTR) - E12-3 (BTR) Always Below 1 Ω
D21- (+B) - E12-1 (+B) Always Below 1 Ω
D21-9 (GND) - E12-2 (GND) Always Below 1 Ω
D21-11 (GTR) or E12-4 (GTR) - Body ground Always 10 kΩ or higher
D21-12 (BTR) or E12-3 (BTR) - Body ground Always 10 kΩ or higher
D21-8 (+B) or E12-1 (+B) - Body ground Always 10 kΩ or higher
D21-9 (GND) or E12-2 (GND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK OUTER REAR VIEW MIRROR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK OUTER REAR VIEW MIRROR ASSEMBLY RH
a.

Disconnect the parking assist light RH connector.


b.

Disconnect the E12 outer rear view mirror assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(E12)Location & Routing

Click Connector(E12)Body>Front Door Wire LH / Front Door Wire RH>Outer Rear View Mirror Assembly RH

B-1 (TH-) - E12-4 (GTR) Always Below 1 Ω
B-2 (TH+) - E12-3 (BTR) Always Below 1 Ω
B-3 (LEDR-) - E12-2 (GND) Always Below 1 Ω
B-4 (LEDR+) - E12-1 (+B) Always Below 1 Ω
B-1 (TH-) or E12-4 (GTR) - Body ground Always 10 kΩ or higher
B-2 (TH+) or E12-3 (BTR) - Body ground Always 10 kΩ or higher
B-3 (LEDR-) or E12-2 (GND) - Body ground Always 10 kΩ or higher
B-4 (LEDR+) or E12-1 (+B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK LIGHT PARKING ASSIST CIRCUIT (PARKING ASSIST LIGHT POWER SOURCE)

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

7.CHECK LIGHT PARKING ASSIST CIRCUIT (PARKING ASSIST LIGHT POWER SOURCE)
a.

Disconnect the E30 outer rear view mirror assembly LH connector.


b.

Enter the following menus: Body Electrical / Clearance Warning / Utility.

Chassis > Circumference Monitoring Camera Control Module > Utility
Tester Display
IR Projector Inspection
50005 470 4641

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(E30)Location & Routing

Click Connector(E30)Body>Front Door Wire LH / Front Door Wire RH>Outer Rear View Mirror Assembly LH

E30-1 (+B) - Body ground IR Emitter Illumination Trigger OFF Below 1 V
E30-1 (+B) - Body ground IR Emitter Illumination Trigger ON 41 to 48 V



Result:
Proceed to
OK
NG



OK

8.CHECK PARKING ASSIST LIGHT LH

NG

REPLACE LIGHT PARKING ASSIST CIRCUIT

8.CHECK PARKING ASSIST LIGHT LH
a.
E456276C03
1.521,0.156 2.031,0.427 0.51,0.271 0.865,1.875 1.031,1.875 1.031,1.875 1.854,1.094 true 2.146,1.677 2.281,1.958 2.281,1.958 2.448,1.958 true 2.063,1.021 2.292,0.302 2.292,0.302 2.458,0.302 true 0.125,0.083 0.438,0.281 0.313,0.198 10 false *a 2.521,1.875 2.833,2.073 0.313,0.198 10 false *1 1.635,0.188 1.958,0.365 0.323,0.177 10 false D21 2.521,0.219 2.833,0.417 0.313,0.198 10 false +B 0.552,1.792 0.865,1.99 0.313,0.198 10 false GND
*1 Service Wire
*a Rear view of wire harness connector
(to Light Parking Assist Circuit)


Using a service wire, connect terminals 6 (+B) and 7 (GND) of kight parking assist circuit connector.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



b.

Cover the bottom of the outer rear view mirror assembly with your hand or a cloth.


c.

According to the display on the GTS, illuminate the parking assist light and check for changes in the multi-display screen display.

HINT:
·

When the parking assist light illuminates, the multi-display screen display will appear to be illuminated by a purplish light.

·

It is necessary to turn the ignition switch off once to illuminate the parking assist light again.




Result:
Result Proceed to
Parking assist light RH illuminate A
Parking assist light RH not illuminate B



A

REPLACE PARKING ASSIST LIGHT LH

B

REPLACE PARKING ASSIST LIGHT RH

9.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH - LIGHT PARKING ASSIST CIRCUIT)
a.

Disconnect the D21 light parking assist circuit connector.


b.

Disconnect the E30 outer rear view mirror assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D21,E30)Location & Routing

Click Connector(D21)Instrument Panel>Instrument Panel Wire>Light Parking Assist Circuit

Click Connector(E30)Body>Front Door Wire LH / Front Door Wire RH>Outer Rear View Mirror Assembly LH

D21-2 (GTL) - E30-4 (GTL) Always Below 1 Ω
D21-3 (BTL) - E30-3 (BTL) Always Below 1 Ω
D21-6 (+B) - E30-1 (+B) Always Below 1 Ω
D21-7 (GND) - E30-2 (GND) Always Below 1 Ω
D21-2 (GTL) or E30-4 (GTL) - Body ground Always 10 kΩ or higher
D21-3 (BTL) or E30-3 (BTL) - Body ground Always 10 kΩ or higher
D21-6 (+B) or E30-1 (+B) - Body ground Always 10 kΩ or higher
D21-7 (GND) or E30-2 (GND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK OUTER REAR VIEW MIRROR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK OUTER REAR VIEW MIRROR ASSEMBLY LH
a.

Disconnect the parking assist light LH connector.


b.

Disconnect the E30 outer rear view mirror assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(E30)Location & Routing

Click Connector(E30)Body>Front Door Wire LH / Front Door Wire RH>Outer Rear View Mirror Assembly LH

A-1 (TH-) - E30-4 (GTL) Always Below 1 Ω
A-2 (TH+) - E30-3 (BTL) Always Below 1 Ω
A-3 (LEDL-) - E30-2 (GND) Always Below 1 Ω
A-4 (LEDL+) - E30-1 (+B) Always Below 1 Ω
A-1 (TH-) or E30-4 (GTL) - Body ground Always 10 kΩ or higher
A-2 (TH+) or E30-3 (BTL) - Body ground Always 10 kΩ or higher
A-3 (LEDL-) or E30-2 (GND) - Body ground Always 10 kΩ or higher
A-4 (LEDL+) or E30-1 (+B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.REPLACE PARKING ASSIST LIGHT LH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

11.REPLACE PARKING ASSIST LIGHT LH
a.

Replace the parking assist light LH with a known good one.

Click hereADAS / AD>ADVANCED PARK>PARKING ASSIST LIGHT>REMOVAL


Result:
Proceed to
NEXT



NEXT

12.CHECK LIGHT PARKING ASSIST CIRCUIT OPERATION
12.CHECK LIGHT PARKING ASSIST CIRCUIT OPERATION
a.

Enter the following menus: Chassis / Clearance Warning / Utility.

Chassis > Circumference Monitoring Camera Control Module > Utility
Tester Display
IR Projector Inspection
50005 470 4641

b.

Cover the bottom of the outer rear view mirror assembly with your hand or a cloth.


c.

According to the display on the GTS, illuminate the parking assist light and check for changes in the multi-display screen display.

HINT:
·

When the parking assist light illuminates, the multi-display screen display will appear to be illuminated by a purplish light.

·

It is necessary to turn the ignition switch off once to illuminate the parking assist light again.




Result:
Result Proceed to
Parking assist lights illuminate A
Parking assist lights not illuminate B



A

END (PARKING ASSIST LIGHT LH WAS DEFECTIVE)

B

REPLACE LIGHT PARKING ASSIST CIRCUIT

13.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY RH - LIGHT PARKING ASSIST CIRCUIT)
a.

Disconnect the D21 light parking assist circuit connector.


b.

Disconnect the E12 outer rear view mirror assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D21,E12)Location & Routing

Click Connector(D21)Instrument Panel>Instrument Panel Wire>Light Parking Assist Circuit

Click Connector(E12)Body>Front Door Wire LH / Front Door Wire RH>Outer Rear View Mirror Assembly RH

D21-11 (GTR) - E12-4 (GTR) Always Below 1 Ω
D21-12 (BTR) - E12-3 (BTR) Always Below 1 Ω
D21-8 (+B) - E12-1 (+B) Always Below 1 Ω
D21-9 (GND) - E12-2 (GND) Always Below 1 Ω
D21-11 (GTR) or E12-4 (GTR) - Body ground Always 10 kΩ or higher
D21-12 (BTR) or E12-3 (BTR) - Body ground Always 10 kΩ or higher
D21-8 (+B) or E12-1 (+B) - Body ground Always 10 kΩ or higher
D21-9 (GND) or E12-2 (GND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.CHECK OUTER REAR VIEW MIRROR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK OUTER REAR VIEW MIRROR ASSEMBLY RH
a.

Disconnect the parking assist light RH connector.


b.

Disconnect the E12 outer rear view mirror assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(E12)Location & Routing

Click Connector(E12)Body>Front Door Wire LH / Front Door Wire RH>Outer Rear View Mirror Assembly RH

B-1 (TH-) - E12-4 (GTR) Always Below 1 Ω
B-2 (TH+) - E12-3 (BTR) Always Below 1 Ω
B-3 (LEDR-) - E12-2 (GND) Always Below 1 Ω
B-4 (LEDR+) - E12-1 (+B) Always Below 1 Ω
B-1 (TH-) or E12-4 (GTR) - Body ground Always 10 kΩ or higher
B-2 (TH+) or E12-3 (BTR) - Body ground Always 10 kΩ or higher
B-3 (LEDR-) or E12-2 (GND) - Body ground Always 10 kΩ or higher
B-4 (LEDR+) or E12-1 (+B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

15.REPLACE PARKING ASSIST LIGHT RH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

15.REPLACE PARKING ASSIST LIGHT RH
a.

Replace the parking assist light RH with a known good one.

Click hereADAS / AD>ADVANCED PARK>PARKING ASSIST LIGHT>REMOVAL


Result:
Proceed to
NEXT



NEXT

16.CHECK LIGHT PARKING ASSIST CIRCUIT OPERATION
16.CHECK LIGHT PARKING ASSIST CIRCUIT OPERATION
a.

Enter the following menus: Chassis / Clearance Warning / Utility.

Chassis > Circumference Monitoring Camera Control Module > Utility
Tester Display
IR Projector Inspection
50005 470 4641

b.

Cover the bottom of the outer rear view mirror assembly with your hand or a cloth.


c.

According to the display on the GTS, illuminate the parking assist light and check for changes in the multi-display screen display.

HINT:
·

When the parking assist light illuminates, the multi-display screen display will appear to be illuminated by a purplish light.

·

It is necessary to turn the ignition switch off once to illuminate the parking assist light again.




Result:
Result Proceed to
Parking assist lights illuminate A
Parking assist lights not illuminate B



A

END (PARKING ASSIST LIGHT RH WAS DEFECTIVE)

B

REPLACE LIGHT PARKING ASSIST CIRCUIT

17.INSPECT IR RELAY

Click hereADAS / AD>ADVANCED PARK>RELAY>INSPECTION

Result:
Proceed to
OK
NG



OK

18.CHECK HARNESS AND CONNECTOR (NV IR RELAY POWER SOURCE)

NG

REPLACE IR RELAY

18.CHECK HARNESS AND CONNECTOR (NV IR RELAY POWER SOURCE)
a.
B472073C16
0.156,0.115 0.469,0.313 0.313,0.198 10 false *a
*a Front view of wire harness connector
(NV IR Relay)


Remove the NV IR relay from no. 1 front compartment relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
IR relay terminal 1 - Body ground Ignition Switch ON 11 to 14 V
Ignition Switch off Below 1V
IR relay terminal 5 - Body ground Ignition Switch ON 11 to 14 V
Ignition Switch off Below 1V



Result:
Proceed to
OK
NG



OK

19.CHECK HARNESS AND CONNECTOR (NV IR RELAY - PARKING ASSIST ECU AND LIGHT PARKING ASSIST CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (NV IR RELAY - PARKING ASSIST ECU AND LIGHT PARKING ASSIST CIRCUIT)
a.

Remove the NV IR relay from no. 1 front compartment relay block.


b.

Disconnect the G13 parking assist ECU connector.


c.

Disconnect the D21 light parking assist circuit connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G13,D21)Location & Routing

Click Connector(G13)Body>Floor Wire / No. 3 Floor Wire>Parking Assist ECU

Click Connector(D21)Instrument Panel>Instrument Panel Wire>Light Parking Assist Circuit

IR relay terminal 2 - G13-8 (IRSW) Always Below 1 Ω
IR relay terminal 3 - D21-4 (IG) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

20.REPLACE LIGHT PARKING ASSIST CIRCUIT

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.REPLACE LIGHT PARKING ASSIST CIRCUIT
a.

Replace the parking assist circuit with a known good one.

Click hereADAS / AD>ADVANCED PARK>PARKING ASSIST LIGHT CONTROL RELAY>REMOVAL


Result:
Proceed to
NEXT



NEXT

21.CHECK LIGHT PARKING ASSIST CIRCUIT OPERATION
21.CHECK LIGHT PARKING ASSIST CIRCUIT OPERATION
a.

Enter the following menus: Chassis / Clearance Warning / Utility.

Chassis > Circumference Monitoring Camera Control Module > Utility
Tester Display
IR Projector Inspection
50005 470 4641

b.

Cover the bottom of the outer rear view mirror assembly with your hand or a cloth.


c.

According to the display on the GTS, illuminate the parking assist light and check for changes in the multi-display screen display.

HINT:
·

When the parking assist light illuminates, the multi-display screen display will appear to be illuminated by a purplish light.

·

It is necessary to turn the ignition switch off once to illuminate the parking assist light again.




Result:
Result Proceed to
Parking assist lights illuminate A
Parking assist lights not illuminate B



A

END (LIGHT PARKING ASSIST CIRCUIT WAS DEFECTIVE)

B