Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P06881F  ECM/PCM Power Relay Sense Circuit Intermittent  


DESCRIPTION

This DTC indicates that the EV control ECU detected an instantaneous interruption in +B power source voltage.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P06881F ECM/PCM Power Relay Sense Circuit Intermittent When the ignition switch ON (READY), the EV control ECU is reset due to an instantaneous interruption of power source.
(1 trip detection logic)
·

Wire harness or connector

·

EV control ECU


Master Warning:
Comes on
EV A

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 10 minutes or more.

3.

Turn the ignition switch to ON (READY) and wait for 30 seconds or more.

(If the DTC is not output, drive the vehicle on urban roads according to the freeze frame data item "Vehicle Speed" for approximately 5 minutes.)

4.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

for LHD:
A479445E02
5.896,2.396 6.969,2.635 1.073,0.24 10 false EV Control ECU 4.104,1.063 4.802,1.292 0.698,0.229 10 false PM-IGCT 3.052,1.813 3.75,1.99 0.698,0.177 10 false IGCT NO.2 1.677,1.094 2.375,1.323 0.698,0.229 10 false IGCT NO.2 0.917,1.667 1.771,1.958 0.854,0.292 10 false R/B RR#2 1.073,2.563 2.354,2.854 1.281,0.292 10 false Auxiliary Battery 6.083,1.302 6.479,1.51 0.396,0.208 10 false MREL 6.115,0.927 6.51,1.135 0.396,0.208 10 false +B2 6.125,0.406 6.521,0.615 0.396,0.208 10 false +B1 5.729,0.417 6.125,0.625 0.396,0.208 10 false A17 5.75,0.917 6.146,1.125 0.396,0.208 10 false A8 5.74,1.417 6.135,1.625 0.396,0.208 10 false A8 5.771,1.198 5.969,1.406 0.198,0.208 10 false 21 5.802,0.698 6,0.906 0.198,0.208 10 false 7 5.781,0.188 5.979,0.396 0.198,0.208 10 false 1 3.771,1.531 3.969,1.74 0.198,0.208 10 false 2 2.854,1.521 3.052,1.729 0.198,0.208 10 false 1 2.854,1.052 3.052,1.26 0.198,0.208 10 false 3 3.792,1.021 3.99,1.229 0.198,0.208 10 false 5 4.219,0.792 4.417,1 0.198,0.208 10 false 1 4.479,0.792 4.677,1 0.198,0.208 10 false 2

for RHD:
A479445E01
5.896,2.396 6.969,2.635 1.073,0.24 10 false EV Control ECU 4.104,1.063 4.802,1.292 0.698,0.229 10 false PM-IGCT 3.052,1.813 3.75,1.99 0.698,0.177 10 false IGCT NO.2 1.677,1.094 2.375,1.323 0.698,0.229 10 false IGCT NO.2 0.917,1.667 1.771,1.958 0.854,0.292 10 false R/B RR#2 1.073,2.563 2.354,2.854 1.281,0.292 10 false Auxiliary Battery 6.083,1.302 6.479,1.51 0.396,0.208 10 false MREL 6.115,0.927 6.51,1.135 0.396,0.208 10 false +B2 6.125,0.406 6.521,0.615 0.396,0.208 10 false +B1 5.729,0.417 6.125,0.625 0.396,0.208 10 false A17 5.719,0.917 6.115,1.125 0.396,0.208 10 false D15 5.708,1.406 6.104,1.615 0.396,0.208 10 false D15 5.771,1.198 5.969,1.406 0.198,0.208 10 false 21 5.802,0.698 6,0.906 0.198,0.208 10 false 7 5.781,0.188 5.979,0.396 0.198,0.208 10 false 1 3.771,1.531 3.969,1.74 0.198,0.208 10 false 2 2.854,1.521 3.052,1.729 0.198,0.208 10 false 1 2.854,1.052 3.052,1.26 0.198,0.208 10 false 3 3.792,1.021 3.99,1.229 0.198,0.208 10 false 5 4.219,0.792 4.417,1 0.198,0.208 10 false 1 4.479,0.792 4.677,1 0.198,0.208 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK AUXILIARY BATTERY TERMINAL
a.

Confirm whether the auxiliary battery terminals have been disconnected recently.

Result:
Result Proceed to
Terminals have been disconnected. A
Terminals have not been disconnected. B




A

2.CONFIRM MASTER WARNING

B

6.CHECK AUXILIARY BATTERY TERMINAL (CONTACT PROBLEM)
2.CONFIRM MASTER WARNING

Pre-procedure1

a.

Turn the ignition switch to ON (READY) from off.


Procedure1

a.

Confirm that the master warning illuminates.

Result:
Result Proceed to
Master warning illuminates. A
Master warning does not illuminate. B


NOTICE:

DTC P06881F may be stored after disconnecting and reconnecting the auxiliary battery terminals. If this happens, the DTC will not be output if the ignition switch is turned off and then to ON (READY) again. In this case, clear the DTCs to complete the inspection.



Post-procedure1

a.

Turn the ignition switch off.



A

3.READ DTC OUTPUT

B

END

3.READ DTC OUTPUT

Pre-procedure1

a.

None.


Procedure1

a.

Read and record the DTCs and freeze frame data.

Powertrain > EV > Trouble Codes
50001 397
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

4.CLEAR DTC
4.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

a.

Clear the DTCs and freeze frame data.

Powertrain > EV > Clear DTCs
50002 397
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for 10 minutes or more.



NEXT

5.CHECK DTC OUTPUT (EV)
5.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
Only P06881F is output A
None of the above conditions are met B



Post-procedure1

a.

Turn the ignition switch off.



A

6.CHECK AUXILIARY BATTERY TERMINAL (CONTACT PROBLEM)

B

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

6.CHECK AUXILIARY BATTERY TERMINAL (CONTACT PROBLEM)
a.

Check the connection of the auxiliary battery terminal.

OK:

The terminal is connected securely and there is no contact problem.



Result:
Proceed to
OK
NG



OK

7.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)

NG

CONNECT SECURELY

7.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)

OK

8.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - IGCT NO.2 RELAY)

NG

CONNECT SECURELY

8.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - IGCT NO.2 RELAY)

Pre-procedure1

a.

Remove the IGCT NO. 2 relay from the luggage room relay block.


Procedure1

a.

Disconnect the A8*1 or D15*2 and A17 EV control ECU connector.

*1: for LHD

*2: for RHD


b.

Measure the resistance according to the value(s) in the table below.

A479446C03
5.615,0.458 6.031,0.75 0.417,0.292 6.125,0.458 6.542,0.75 0.417,0.292 6.146,0.073 6.563,0.365 0.417,0.292 5.615,2.438 5.958,1.854 true 6.469,2.458 6.188,1.875 true 0.156,0.104 0.469,0.26 0.313,0.156 10 false *1 2.521,0.615 2.833,0.771 0.313,0.156 10 false *2 4.01,0.115 4.323,0.271 0.313,0.156 10 false *a 5.729,0.542 6.188,0.74 0.458,0.198 10 false A17 6.25,0.125 6.708,0.323 0.458,0.198 10 false A8 5.469,2.448 5.927,2.646 0.458,0.198 10 false +B1 6.458,2.448 6.917,2.646 0.458,0.198 10 false +B2 6.24,0.531 6.698,0.729 0.458,0.198 10 false D15 6.646,0.135 6.958,0.333 0.313,0.198 10 false *A 6.656,0.51 6.969,0.708 0.313,0.198 10 false *B
*A for LHD *B for RHD
*1 Luggage Room Relay Block *2 IGCT NO.2 Relay
*a Rear view of wire harness connector
(to EV Control ECU)
- -


Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A17,A8)Location & Routing

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(A8)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A17-1 (+B1) - 5 (IGCT NO.2 relay holder) Ignition switch off Below 1 Ω
A8-7 (+B2) - 5 (IGCT NO.2 relay holder) Ignition switch off Below 1 Ω

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A17,D15)Location & Routing

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(D15)Instrument Panel>Instrument Panel Wire>EV Control ECU

A17-1 (+B1) - 5 (IGCT NO.2 relay holder) Ignition switch off Below 1 Ω
D15-7 (+B2) - 5 (IGCT NO.2 relay holder) Ignition switch off Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A8*1 or D15*2 and A17 EV Control ECU connector.

*1: for LHD

*2: for RHD


b.

Install the IGCT NO. 2 relay.



OK

9.CHECK FOR INTERMITTENT PROBLEMS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK FOR INTERMITTENT PROBLEMS
a.

Check for intermittent problems.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS


i.

Check the connection and terminal contact pressure of the connectors and wire harnesses between the EV control ECU and the luggage room relay block.


ii.

When the ignition switch is ON (READY), jiggle the connectors and wire harnesses between the EV control ECU and the luggage room relay block.



Result:
Result Proceed to
Problem symptom does not recur. A
Problem symptom recurs. B



A

B

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA