Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A2A11  Drive Motor "A" Temperature Sensor Circuit Short to Ground  P0A2A15  Drive Motor "A" Temperature Sensor Circuit Short to Auxiliary Battery or Open  


DTC SUMMARY

MALFUNCTION DESCRIPTION


These DTCs are stored when the motor temperature sensor output is abnormal. The cause of this malfunction may be one of the following:

EV control ECU internal malfunction
·

EV control ECU malfunction


Motor temperature sensor malfunction
·

Internal motor temperature sensor malfunction

·

Open or short in motor temperature sensor


Wire harness between the motor temperature sensor and EV control ECU
·

The connectors are not connected properly

·

Foreign matter or water on the connector terminals

·

Open or short in wire harness


HINT:

If any of these DTCs are stored, the motor temperature sensor is malfunctioning and the self-protection function may not operate. Therefore under certain high load driving condition, the temperature of the motor (MG2) becomes high. If the self-protection function does not operate, the motor (MG2) may malfunction and cause the vehicle to enter fail-safe mode.



DESCRIPTION

The resistance of the thermistor built into the motor temperature sensor changes in accordance with changes in the motor (MG2) temperature. The lower the motor (MG2) temperature, the higher the thermistor resistance. Conversely, the higher the motor (MG2) temperature, the lower the resistance.

HINT:

The term "drive motor A" indicates the motor (MG2).


C189867E17
0.76,2.104 0.885,2.302 0.125,0.198 10 false 0 2,2.875 3.406,3.094 1.406,0.219 10 false Temperature (°C (°F)) 0.885,2.375 1.083,2.573 0.198,0.198 10 false 10 1.26,2.375 1.458,2.573 0.198,0.198 10 false 15 2.406,2.375 2.604,2.573 0.198,0.198 10 false 30 2.792,2.375 2.99,2.573 0.198,0.198 10 false 35 1.646,2.375 1.844,2.573 0.198,0.198 10 false 20 2.021,2.375 2.219,2.573 0.198,0.198 10 false 25 0.677,1.521 0.875,1.719 0.198,0.198 10 false 50 0.594,0.948 0.865,1.146 0.271,0.198 10 false 100 3.146,2.375 3.344,2.573 0.198,0.198 10 false 40 0.063,0.5 1.26,0.771 1.198,0.271 10 false Resistance (kΩ) 0.865,2.542 1.208,2.74 0.344,0.198 10 false (50) 1.229,2.552 1.573,2.75 0.344,0.198 10 false (59) 1.615,2.552 1.958,2.75 0.344,0.198 10 false (68) 1.979,2.563 2.323,2.76 0.344,0.198 10 false (77) 2.385,2.573 2.729,2.771 0.344,0.198 10 false (86) 2.771,2.583 3.115,2.781 0.344,0.198 10 false (95) 3.063,2.583 3.406,2.781 0.344,0.198 10 false (104)

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P0A2A11 Drive Motor "A" Temperature Sensor Circuit Short to Ground Line short or short to ground in the motor temperature sensor circuit
(1 trip detection logic)
·

Wire harness or connector

·

EV control ECU

·

FCV with motor transaxle assembly (Motor temperature sensor)


Master Warning:
Comes on
EV A
P0A2A15 Drive Motor "A" Temperature Sensor Circuit Short to Auxiliary Battery or Open Open or short to +B in the motor temperature sensor circuit
(1 trip detection logic)
·

Wire harness or connector

·

EV control ECU

·

FCV with motor transaxle assembly (Motor temperature sensor)


Master Warning:
Comes on
EV A

Related Data List
DTC No. Data List
P0A2A11 Motor Temperature
P0A2A15

HINT:

After confirming that DTC P0A2A11 or P0A2A15 is output, use the GTS to check "Motor Temperature" in the Data List.

Displayed Temperature Malfunction
-40°C (-40°F) Open circuit or short to +B
215°C (419°F) Short circuit or short to ground


CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 10 minutes or more.

3.

Turn the ignition switch to ON and wait for 5 seconds or more.

4.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

for LHD:
C384732E09
1.865,1.135 2.229,1.333 0.365,0.198 10 false MMT 1.76,1.896 2.219,2.083 0.458,0.188 10 false MMTG 4.865,1.135 5.229,1.333 0.365,0.198 10 false MMT 4.875,1.896 5.333,2.083 0.458,0.188 10 false MMTG 0.313,2.625 0.698,2.813 0.385,0.188 10 false G154 0.323,2.802 2.615,3.198 2.292,0.396 10 false FCV with Motor Transaxle Assembly (Motor Temperature Sensor) 2.844,2.542 3.167,2.729 0.323,0.188 10 false GG2 2.844,2.698 4.615,2.906 1.771,0.208 10 false NO. 3 Floor Wire Connector 5.052,2.667 5.542,2.844 0.49,0.177 10 false G14 5.052,2.823 6.469,3.177 1.417,0.354 10 false EV Control ECU 3,1.146 3.208,1.323 0.208,0.177 10 false 13 3.688,1.156 3.896,1.333 0.208,0.177 10 false 13 3.01,1.896 3.219,2.073 0.208,0.177 10 false 14 3.688,1.896 3.896,2.073 0.208,0.177 10 false 14 4.573,1.135 4.781,1.313 0.208,0.177 10 false 21 4.573,1.885 4.781,2.063 0.208,0.177 10 false 31 5.938,1.271 6.313,1.469 0.375,0.198 10 false ADC 2.302,1.146 2.531,1.344 0.229,0.198 10 false 14 2.302,1.896 2.438,2.073 0.135,0.177 10 false 2

for RHD:
A466134E03
5.385,2.823 7.031,3.01 1.646,0.188 10 false EV Control ECU 6.51,0.792 6.969,0.99 0.458,0.198 10 false ADC 5.396,0.688 5.854,0.885 0.458,0.198 10 false MMT 5.375,1.865 5.927,2.073 0.552,0.208 10 false MMTG 1.333,0.667 1.792,0.865 0.458,0.198 10 false MMT 1.219,1.875 1.771,2.083 0.552,0.208 10 false MMTG 0.188,2.854 2.115,3.385 1.927,0.531 10 false FCV with Motor Transaxle Assembly (Motor Temperature Sensor) 2.365,0.656 2.823,0.854 0.458,0.198 10 false 13 2.323,2.719 3.323,3.125 1,0.406 10 false NO. 3 Floor Wire Connector 5.094,0.677 5.552,0.875 0.458,0.198 10 false 21 5.104,1.865 5.563,2.063 0.458,0.198 10 false 31 5.385,2.677 5.844,2.875 0.458,0.198 10 false A14 0.198,2.688 0.656,2.885 0.458,0.198 10 false G154 2.323,2.552 2.635,2.75 0.313,0.198 10 false GG2 3.031,1.865 3.49,2.063 0.458,0.198 10 false 14 3.802,1.854 4.104,2.042 0.302,0.188 10 false 2 4.448,0.677 4.906,0.875 0.458,0.198 10 false 21 3.042,0.656 3.5,0.854 0.458,0.198 10 false 13 1.76,0.667 2.219,0.865 0.458,0.198 10 false 14 1.75,1.854 2.208,2.052 0.458,0.198 10 false 2 2.354,1.865 2.813,2.063 0.458,0.198 10 false 14 3.781,0.667 4.24,0.865 0.458,0.198 10 false 21 4.458,1.854 4.76,2.042 0.302,0.188 10 false 2 3.698,2.552 4.01,2.75 0.313,0.198 10 false AG2 3.708,2.729 4.698,3.135 0.99,0.406 10 false NO. 2 Floor Wire Connector

PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)
a.

Check the connector connections and contact pressure of the relevant terminals for the EV control ECU connectors.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


A479018C03
0.344,0.094 0.656,0.292 0.313,0.198 10 false *A 3.813,0.094 4.125,0.292 0.313,0.198 10 false *B
*A for LHD *B for RHD


OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.



Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

2.CHECK CONNECTOR CONNECTION CONDITION (NO. 3 FLOOR WIRE CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK CONNECTOR CONNECTION CONDITION (NO. 3 FLOOR WIRE CONNECTOR)
a.
A479480

Check the connection condition of the No. 3 floor wire connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connectors.



Result:
Result Proceed to
OK
(for LHD)
A
OK
(for RHD)
B
NG (The connector is not connected securely.) C
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) D



A

4.CHECK CONNECTOR CONNECTION CONDITION (MOTOR TEMPERATURE SENSOR CONNECTOR)

B

3.CHECK CONNECTOR CONNECTION CONDITION (NO. 2 FLOOR WIRE CONNECTOR)

C

CONNECT SECURELY

D

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CONNECTOR CONNECTION CONDITION (NO. 2 FLOOR WIRE CONNECTOR)
a.
A484682C01
0,0 0.313,0.198 0.313,0.198 10 true *A 0,2.458 0.313,2.656 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Check the connection condition of the No. 2 floor wire connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connectors.



Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

4.CHECK CONNECTOR CONNECTION CONDITION (MOTOR TEMPERATURE SENSOR CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK CONNECTOR CONNECTION CONDITION (MOTOR TEMPERATURE SENSOR CONNECTOR)
a.
A479479

Check the connection condition of the motor temperature sensor connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.



Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

5.READ VALUE USING GTS (MOTOR TEMPERATURE)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.READ VALUE USING GTS (MOTOR TEMPERATURE)

Pre-procedure1

a.

None.


Procedure1

a.

Read the Data List.

Powertrain > EV > Data List
Tester Display
Motor Temperature
50003 397 66
Result:
Result Proceed to
The value of Motor Temperature is -40 °C A
The value of Motor Temperature is 215 °C B
None of the above conditions are met C


HINT:
·

-40°C = -40°F

·

215°C = 419°F




Post-procedure1

a.

Turn the ignition switch off.



A

6.INSPECT FCV WITH MOTOR TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR)

B

8.INSPECT FCV WITH MOTOR TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT FCV WITH MOTOR TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR)

Pre-procedure1

a.
A479479

Disconnect the G154 motor temperature sensor connector.


Procedure1

a.
A479452C01
1.458,0.208 1.969,0.583 0.51,0.375 1.969,1.073 2.406,1.813 true 1.104,1.823 1.427,1.438 true 0.135,0.167 0.448,0.365 0.313,0.198 10 false *a 0.792,1.844 1.25,2.042 0.458,0.198 10 false MMT 2.302,1.844 2.76,2.042 0.458,0.198 10 false MMTG 1.563,0.323 1.958,0.521 0.396,0.198 10 false G154
*a Component without harness connected
(FCV With Motor Transaxle Assembly (Motor Temperature Sensor))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G154)Location & Routing

Click Connector(G154)Body>Floor Wire / No. 3 Floor Wire>FCV Transaxle with Motor Assembly

G154-14 (MMT) - G154-2 (MMTG) Ignition switch off 0.3 to 2100 kΩ


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the G154 motor temperature sensor connector.



OK

7.CHECK EV CONTROL ECU

NG

REPLACE FCV WITH MOTOR TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR)

7.CHECK EV CONTROL ECU

Pre-procedure1

a.
A478491C46
0.281,0.802 0.677,1.156 0.396,0.354 0.292,0.344 0.688,0.698 0.396,0.354 0.49,1.896 0.271,2.479 true 0.49,1.823 1.167,2.469 true 0.104,0.104 0.417,0.26 0.313,0.156 10 false *a 0.365,0.438 0.667,0.604 0.302,0.167 10 false G14 0.063,2.51 0.688,2.708 0.625,0.198 10 false MMTG 1.063,2.5 1.448,2.667 0.385,0.167 10 false MMT 0.365,0.906 0.667,1.073 0.302,0.167 10 false A14 0.781,0.458 1.094,0.656 0.313,0.198 10 false *A 0.771,0.927 1.083,1.125 0.313,0.198 10 false *B
*A for LHD
*B for RHD
*a Component with harness connected
(EV Control ECU)


for LHD:

Connect terminals G14-21 (MMT) and G14-31 (MMTG) of the EV control ECU connector.

for RHD:

Connect terminals A14-21 (MMT) and A14-31 (MMTG) of the EV control ECU connector.


Procedure1

a.

Read the Data List.

Powertrain > EV > Data List
Tester Display
Motor Temperature
50003 397 66
OK:
for LHD:
Tester Display Condition Specified Condition
Motor Temperature Terminals G14-21 (MMT) and G14-31 (MMTG) connected
Ignition switch ON
215°C (419°F)

for RHD:
Tester Display Condition Specified Condition
Motor Temperature Terminals A14-21 (MMT) and A14-31 (MMTG) connected
Ignition switch ON
215°C (419°F)


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 3 FLOOR WIRE CONNECTOR - EV CONTROL ECU)

NG

8.INSPECT FCV WITH MOTOR TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR)

Pre-procedure1

a.
A479479

Disconnect the G154 motor temperature sensor connector.


Procedure1

a.
A479452C01
1.458,0.208 1.969,0.583 0.51,0.375 1.969,1.073 2.406,1.813 true 1.104,1.823 1.427,1.438 true 0.135,0.167 0.448,0.365 0.313,0.198 10 false *a 0.792,1.844 1.25,2.042 0.458,0.198 10 false MMT 2.302,1.844 2.76,2.042 0.458,0.198 10 false MMTG 1.563,0.323 1.958,0.521 0.396,0.198 10 false G154
*a Component without harness connected
(FCV With Motor Transaxle Assembly (Motor Temperature Sensor))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G154)Location & Routing

Click Connector(G154)Body>Floor Wire / No. 3 Floor Wire>FCV Transaxle with Motor Assembly

G154-14 (MMT) - G154-2 (MMTG) Ignition switch off 0.3 to 2100 kΩ


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the G154 motor temperature sensor connector.



OK

9.INSPECT FCV WITH MOTOR TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR CONNECTOR - EV CONTROL ECU)

NG

REPLACE FCV WITH MOTOR TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR)

9.INSPECT FCV WITH MOTOR TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR CONNECTOR - EV CONTROL ECU)

Pre-procedure1

a.

Disconnect the G154 motor temperature sensor connector.


b.

Disconnect the G14*1 or A14*2 EV Control ECU connector.

*1: for LHD

*2: for RHD


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A483154C02
4.25,0.438 4.667,0.74 0.417,0.302 1.573,0.604 1.99,0.906 0.417,0.302 4.25,0.052 4.667,0.354 0.417,0.302 4.865,2.469 4.5,1.979 true 4.26,2.438 4.49,2.031 true 1.646,1.333 1.167,2.167 true 1.948,1.531 2.448,2.208 true 1.625,0.688 2.083,0.885 0.458,0.198 10 false G154 4.354,0.521 4.813,0.719 0.458,0.198 10 false A14 0.219,0.104 0.531,0.302 0.313,0.198 10 false *a 3.479,0.135 3.792,0.333 0.313,0.198 10 false *b 3.865,2.479 4.323,2.677 0.458,0.198 10 false MMTG 4.865,2.479 5.323,2.677 0.458,0.198 10 false MMT 2.396,2.219 2.854,2.417 0.458,0.198 10 false MMT 0.938,2.219 1.396,2.417 0.458,0.198 10 false MMTG 4.344,0.125 4.802,0.323 0.458,0.198 10 false G14 4.76,0.104 5.073,0.302 0.313,0.198 10 false *A 4.76,0.521 5.073,0.719 0.313,0.198 10 false *B
*A for LHD *B for RHD
*a Front view of wire harness connector
(Motor Temperature Sensor)
*b Rear view of wire harness connector
(to EV Control ECU)


Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(G154,G14)Location & Routing

Click Connector(G154)Body>Floor Wire / No. 3 Floor Wire>FCV Transaxle with Motor Assembly

Click Connector(G14)Instrument Panel>Floor Wire>EV Control ECU

G154-14 (MMT) - G14-21 (MMT) Ignition switch off Below 1 Ω
G154-2 (MMTG) - G14-31 (MMTG) Ignition switch off Below 1 Ω
G154-14 (MMT) and G14-21 (MMT) - Body ground and other terminals Ignition switch off 10 kΩ or higher
G154-2 (MMTG) and G14-31 (MMTG) - Body ground and other terminals Ignition switch off 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(G154,A14)Location & Routing

Click Connector(G154)Body>Floor Wire / No. 3 Floor Wire>FCV Transaxle with Motor Assembly

Click Connector(A14)Instrument Panel>Front Compartment Main Wire>EV Control ECU

G154-14 (MMT) - A14-21 (MMT) Ignition switch off Below 1 Ω
G154-2 (MMTG) - A14-31 (MMTG) Ignition switch off Below 1 Ω
G154-14 (MMT) and A14-21 (MMT) - Body ground and other terminals Ignition switch off 10 kΩ or higher
G154-2 (MMTG) and A14-31 (MMTG) - Body ground and other terminals Ignition switch off 10 kΩ or higher



Result:
Proceed to
OK
NG


b.

Reconnect the G14*1 or A14*2 EV Control ECU connector.

*1: for LHD

*2: for RHD


Post-procedure1

a.

Reconnect the G154 motor temperature sensor connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 3 FLOOR WIRE CONNECTOR - EV CONTROL ECU)