Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A2A1C  Drive Motor "A" Temperature Sensor Voltage Out of Range  P0A2A1F  Drive Motor "A" Temperature Sensor Circuit Intermittent  


DTC SUMMARY

MALFUNCTION DESCRIPTION


These DTCs are stored when the motor temperature sensor output is abnormal. The cause of this malfunction may be one of the following:

Motor temperature sensor malfunction
·

Internal motor temperature sensor malfunction

·

Open or short in motor temperature sensor


Wire harness between the motor temperature sensor and EV control ECU
·

The connectors are not connected properly

·

Foreign matter or water on the connector terminals

·

Open or short in wire harness


HINT:

If any of these DTCs are stored, the motor temperature sensor is malfunctioning and the self-protection function may not operate. Therefore under certain high load driving condition, the temperature of the motor (MG2) becomes high. If the self-protection function does not operate, the motor (MG2) may malfunction and cause the vehicle to enter fail-safe mode.



DESCRIPTION

Refer to the description for DTC P0A2A11.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A2A11

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P0A2A1C Drive Motor "A" Temperature Sensor Voltage Out of Range After a long soak, the value of the motor (MG2) temperature sensor is different from the value of the other temperature sensors.
(2 trip detection logic)
·

Wire harness or connector

·

FCV with motor transaxle assembly (Motor temperature sensor)

·

EV control ECU


Master Warning:
Comes on
EV A
P0A2A1F Drive Motor "A" Temperature Sensor Circuit Intermittent Sudden change in motor temperature sensor output or hunting:
Unusual sudden change in motor temperature sensor output occurs and offset condition continues for a certain period of time, or unusual change in motor temperature sensor output occurs repeatedly.
(1 trip detection logic)
·

Wire harness or connector

·

FCV with motor transaxle assembly (Motor temperature sensor)

·

EV control ECU


Master Warning:
Comes on
EV A

Related Data List
DTC No. Data List
P0A2A1C
P0A2A1F
·

Motor Temperature

·

FC Air Compressor Motor Temperature



CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


DTC P0A2A1C
1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off.

3.

Leave the vehicle as is for 5 minutes or more and then check the values of the Data List items "FC Air Compressor Motor Temperature", "Motor Temperature" and "Inverter Coolant Temperature".

4.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




DTC P0A2A1F
1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 10 minutes or more.

3.

Turn the ignition switch to ON and wait for 5 seconds or more.

4.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




PROCEDURE

1.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
P0A2A1C or P0A2A1F is output and DTCs other than the DTCs in the table below are output A
Only P0A2A1C or P0A2A1F is output B


Relevant DTC
P0A2A11 Drive Motor "A" Temperature Sensor Circuit Short to Ground
P0A2A15 Drive Motor "A" Temperature Sensor Circuit Short to Auxiliary Battery or Open


Post-procedure1

a.

Turn the ignition switch off.



A

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

B

2.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)
2.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A2A11

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

3.INSPECT FCV WITH MOTOR TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT FCV WITH MOTOR TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR)

Pre-procedure1

a.

Disconnect the G14*1 or A14*2 EV control ECU connector.

*1: for LHD

*2: for RHD


Procedure1

a.
A478492C09
0.406,0.677 0.802,1.031 0.396,0.354 0.406,0.271 0.802,0.625 0.396,0.354 0.479,2.51 0.323,2.927 true 0.49,2.438 1.052,2.948 true 0.104,0.104 0.417,0.26 0.313,0.156 10 false *a 0.49,0.365 0.792,0.531 0.302,0.167 10 false G14 0.063,2.979 0.688,3.177 0.625,0.198 10 false MMTG 1.063,2.958 1.448,3.125 0.385,0.167 10 false MMT 0.49,0.792 0.792,0.958 0.302,0.167 10 false A14 0.885,0.375 1.198,0.573 0.313,0.198 10 false *A 0.885,0.76 1.198,0.958 0.313,0.198 10 false *B
*A for LHD
*B for RHD
*a Rear view of wire harness connector
(to EV Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(G14)Location & Routing

Click Connector(G14)Instrument Panel>Floor Wire>EV Control ECU

G14-21 (MMT) - G14-31 (MMTG) Ignition switch off 0.3 to 2100 kΩ

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A14)Location & Routing

Click Connector(A14)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A14-21 (MMT) - A14-31 (MMTG) Ignition switch off 0.3 to 2100 kΩ


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the G14*1 or A14*2 EV Control ECU connector.

*1: for LHD

*2: for RHD



OK

4.CHECK VEHICLE CONDITION

NG

13.CHECK VEHICLE CONDITION
4.CHECK VEHICLE CONDITION
a.

Choose the model to be inspected.


Result:
Result Proceed to
for LHD A
for RHD B



A

5.CHECK CONNECTOR CONNECTION CONDITION (NO. 3 FLOOR WIRE CONNECTOR)

B

9.CHECK CONNECTOR CONNECTION CONDITION (NO. 2 FLOOR WIRE CONNECTOR)
5.CHECK CONNECTOR CONNECTION CONDITION (NO. 3 FLOOR WIRE CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A2A11

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

6.CHECK HARNESS AND CONNECTOR (NO. 3 FLOOR WIRE CONNECTOR - EV CONTROL ECU)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (NO. 3 FLOOR WIRE CONNECTOR - EV CONTROL ECU)

Pre-procedure1

a.

Disconnect the GG2 No. 3 floor wire connector.


b.

Disconnect the G14*1 or A14*2 EV control ECU.

*1: for LHD

*2: for RHD


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A479453C04
4.25,0.438 4.667,0.74 0.417,0.302 1.573,0.604 1.99,0.906 0.417,0.302 4.25,0.094 4.667,0.396 0.417,0.302 4.865,2.469 4.5,1.979 true 4.26,2.438 4.49,2.031 true 2.073,1.563 1.573,2.198 true 2.177,1.563 2.677,2.188 true 1.667,0.698 2.125,0.896 0.458,0.198 10 false GG2 4.333,0.51 4.792,0.708 0.458,0.198 10 false A14 0.302,0.125 0.615,0.323 0.313,0.198 10 false *a 3.563,0.188 3.875,0.385 0.313,0.198 10 false *b 3.865,2.479 4.323,2.677 0.458,0.198 10 false MMTG 4.865,2.479 5.323,2.677 0.458,0.198 10 false MMT 2.656,2.219 3.115,2.417 0.458,0.198 10 false MMT 1.323,2.219 1.781,2.417 0.458,0.198 10 false MMTG 4.323,0.177 4.781,0.375 0.458,0.198 10 false G14 4.771,0.177 5.083,0.375 0.313,0.198 10 false *A 4.781,0.51 5.094,0.708 0.313,0.198 10 false *B
*A for LHD *B for RHD
*a Front view of wire harness connector
(No. 3 Floor Wire Connector)
*b Rear view of wire harness connector
(to EV Control ECU)


Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(GG2,G14)Location & Routing

Click Connector(GG2)Body>Floor Wire / No. 3 Floor Wire>No. 3 Floor Wire and Floor Wire

Click Connector(G14)Instrument Panel>Floor Wire>EV Control ECU

GG2-13 (MMT) - G14-21 (MMT) Ignition switch off Below 1 Ω
GG2-14 (MMTG) - G14-31 (MMTG) Ignition switch off Below 1 Ω
GG2-13 (MMT) or G14-21 (MMT) - Body ground and other terminals Ignition switch off 10 kΩ or higher
GG2-14 (MMTG) or G14-31 (MMTG) - Body ground and other terminals Ignition switch off 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(GG2,A14)Location & Routing

Click Connector(GG2)Body>Floor Wire / No. 3 Floor Wire>No. 3 Floor Wire and Floor Wire

Click Connector(A14)Instrument Panel>Front Compartment Main Wire>EV Control ECU

GG2-13 (MMT) - A14-21 (MMT) Ignition switch off Below 1 Ω
GG2-14 (MMTG) - A14-31 (MMTG) Ignition switch off Below 1 Ω
GG2-13 (MMT) or A14-21 (MMT) - Body ground and other terminals Ignition switch off 10 kΩ or higher
GG2-14 (MMTG) or A14-31 (MMTG) - Body ground and other terminals Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the G14*1 or A14*2 EV control ECU.

*1: for LHD

*2: for RHD


b.

Reconnect the GG2 No. 3 floor wire connector.



OK

7.CHECK CONNECTOR CONNECTION CONDITION (MOTOR TEMPERATURE SENSOR CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK CONNECTOR CONNECTION CONDITION (MOTOR TEMPERATURE SENSOR CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A2A11

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

8.CHECK HARNESS AND CONNECTOR (NO. 3 FLOOR WIRE CONNECTOR - FCV WITH MOTOR TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR))

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (NO. 3 FLOOR WIRE CONNECTOR - FCV WITH MOTOR TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR))

Pre-procedure1

a.
A479480N01
2.094,0.427 2.563,0.75 0.469,0.323 2.156,0.479 2.531,0.708 0.375,0.229 10 true GG2

Disconnect the GG2 No. 3 floor wire connector.


b.
A479479

Disconnect the G154 motor temperature sensor connector.


Procedure1

a.
A481508C03
1.458,0.083 2.01,0.5 0.552,0.417 1.438,2.219 1.99,2.635 0.552,0.417 1.104,1.729 1.531,0.969 true 2.271,1.729 1.917,1.208 true 0.927,4.167 1.219,3.552 true 1.656,4.146 1.354,3.552 true 1.604,2.375 2.063,2.573 0.458,0.198 10 false GG2 1.594,0.229 2.052,0.427 0.458,0.198 10 false G154 0.906,1.75 1.365,1.948 0.458,0.198 10 false MMTG 2.177,1.75 2.635,1.948 0.458,0.198 10 false MMT 0.24,2.292 0.698,2.49 0.458,0.198 10 false *b 0.188,0.156 0.646,0.354 0.458,0.198 10 false *a 0.771,4.198 1.229,4.396 0.458,0.198 10 false MMT 1.573,4.198 2.031,4.396 0.458,0.198 10 false MMTG
*a Front view of wire harness connector
(to Motor Temperature Sensor)
*b Front view of wire harness connector
(No. 3 Floor Wire Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(GG2,G154)Location & Routing

Click Connector(GG2)Body>Floor Wire / No. 3 Floor Wire>No. 3 Floor Wire and Floor Wire

Click Connector(G154)Body>Floor Wire / No. 3 Floor Wire>FCV Transaxle with Motor Assembly

GG2-13 (MMT) - G154-14 (MMT) Ignition switch off Below 1 Ω
GG2-14 (MMTG) - G154-2 (MMTG) Ignition switch off Below 1 Ω
GG2-13 (MMT) or G154-14 (MMT) - Body ground and other terminals Ignition switch off 10 kΩ or higher
GG2-14 (MMTG) or G154-2 (MMTG) - Body ground and other terminals Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the G154 motor temperature sensor connector.


b.

Reconnect the GG2 No. 3 floor wire connector.



OK

REPLACE FCV WITH MOTOR TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK CONNECTOR CONNECTION CONDITION (NO. 2 FLOOR WIRE CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A2A11

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

10.CHECK HARNESS AND CONNECTOR (NO. 2 FLOOR WIRE CONNECTOR - EV CONTROL ECU)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (NO. 2 FLOOR WIRE CONNECTOR - EV CONTROL ECU)
a.

Disconnect the AG2 No. 2 floor wire connector.


b.

Disconnect the A14 EV control ECU.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(AG2,A14)Location & Routing

Click Connector(AG2)Instrument Panel>Front Compartment Main Wire>Front Compartment Main Wire and Floor Wire

Click Connector(A14)Instrument Panel>Front Compartment Main Wire>EV Control ECU

AG2-21 (MMT) - A14-21 (MMT) Ignition switch off Below 1 Ω
AG2-2 (MMTG) - A14-31 (MMTG) Ignition switch off Below 1 Ω
AG2-21 (MMT) or A14-21 (MMT) - Body ground and other terminals Ignition switch off 10 kΩ or higher
AG2-2 (MMTG) or A14-31 (MMTG) - Body ground and other terminals Ignition switch off 10 kΩ or higher



Result:
Proceed to
OK
NG


d.

Reconnect the A14 EV control ECU.


e.

Reconnect the AG2 No. 2 floor wire connector.



OK

11.CHECK CONNECTOR CONNECTION CONDITION (NO. 3 FLOOR WIRE CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK CONNECTOR CONNECTION CONDITION (NO. 3 FLOOR WIRE CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A2A11

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

12.CHECK HARNESS AND CONNECTOR (NO. 2 FLOOR WIRE CONNECTOR - NO. 3 FLOOR WIRE CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (NO. 2 FLOOR WIRE CONNECTOR - NO. 3 FLOOR WIRE CONNECTOR)
a.

Disconnect the AG2 No. 2 floor wire connector.


b.

Disconnect the GG2 No. 3 floor wire connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(AG2,GG2)Location & Routing

Click Connector(AG2)Instrument Panel>Front Compartment Main Wire>Front Compartment Main Wire and Floor Wire

Click Connector(GG2)Body>Floor Wire / No. 3 Floor Wire>No. 3 Floor Wire and Floor Wire

AG2-21 (MMT) - GG2-13 (MMT) Ignition switch off Below 1 Ω
AG2-2 (MMTG) - GG2-14(MMTG) Ignition switch off Below 1 Ω
AG2-21 (MMT) or GG2-13 (MMT) - Body ground and other terminals Ignition switch off 10 kΩ or higher
AG2-2 (MMTG) or GG2-14 (MMTG) - Body ground and other terminals Ignition switch off 10 kΩ or higher



Result:
Proceed to
OK
NG


d.

Reconnect the GG2 No. 3 floor wire connector.


e.

Reconnect the AG2 No. 2 floor wire connector.



OK

7.CHECK CONNECTOR CONNECTION CONDITION (MOTOR TEMPERATURE SENSOR CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK VEHICLE CONDITION
a.

Choose the model to be inspected.


Result:
Result Proceed to
for LHD A
for RHD B



A

15.INSPECT FCV WITH MOTOR TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR)

B

14.INSPECT FCV WITH MOTOR TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR)
14.INSPECT FCV WITH MOTOR TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR)

Pre-procedure1

a.
A484682C01
0,0 0.313,0.198 0.313,0.198 10 true *A 0,2.458 0.313,2.656 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Disconnect the AG2 No. 2 floor wire connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(AG2,GG2)Location & Routing

Click Connector(AG2)Instrument Panel>Front Compartment Main Wire>Front Compartment Main Wire and Floor Wire

Click Connector(GG2)Body>Floor Wire / No. 3 Floor Wire>No. 3 Floor Wire and Floor Wire

AG2-21 (MMT) - GG2-2 (MMTG) Ignition switch off 0.3 to 2100 kΩ


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the AG2 No. 2 floor wire connector.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 2 FLOOR WIRE CONNECTOR - EV CONTROL ECU)

NG

15.INSPECT FCV WITH MOTOR TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR)
15.INSPECT FCV WITH MOTOR TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR)

Pre-procedure1

a.
A479480N01
2.094,0.427 2.563,0.75 0.469,0.323 2.156,0.479 2.531,0.708 0.375,0.229 10 true GG2

Disconnect the GG2 No. 3 floor wire connector.


Procedure1

a.
A460769C03
1.458,0.25 1.906,0.563 0.448,0.313 1.365,1.438 1.667,1.875 true 1.24,1.417 0.896,1.865 true 0.094,0.094 0.406,0.292 0.313,0.198 10 false *a 1.563,0.333 2.021,0.531 0.458,0.198 10 false GG2 1.667,1.885 2.125,2.083 0.458,0.198 10 false MMTG 0.667,1.885 1.281,2.083 0.615,0.198 10 false MMT
*a Front view of wire harness connector
(No. 3 Floor Wire Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(GG2)Location & Routing

Click Connector(GG2)Body>Floor Wire / No. 3 Floor Wire>No. 3 Floor Wire and Floor Wire

GG2-13 (MMT) - GG2-14 (MMTG) Ignition switch off 0.3 to 2100 kΩ


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the GG2 No. 3 floor wire connector.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 3 FLOOR WIRE CONNECTOR - EV CONTROL ECU)

NG

16.INSPECT FCV WITH MOTOR TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR)
16.INSPECT FCV WITH MOTOR TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR)

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

REPLACE FCV WITH MOTOR TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR)