Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2020.11–2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0AED1C  Drive Motor Inverter Temperature Sensor "A" Circuit Voltage Out of Range  P0AED1F  Drive Motor Inverter Temperature Sensor "A" Circuit Intermittent  


DTC SUMMARY

MALFUNCTION DESCRIPTION


These DTCs indicate the temperature sensor value for drive motor inverter is abnormal. The cause of this malfunction may be one of the following:

Internal inverter malfunction

Inverter with converter assembly internal circuit malfunction


EV cooling system malfunction

Coolant circulation abnormal (frozen or leaking, etc.)


Inverter low-voltage circuit malfunction

The connectors are not connected properly



DESCRIPTION

The MG ECU, which is built into in the inverter with converter assembly, detects the temperature of the drive motor inverter using the temperature sensor built into the drive motor inverter. If necessary, the MG ECU will limit inverter output to help prevent drive motor inverter overheating. The EV control ECU also detects malfunctions in the sensor based on the temperature sensor values. The inverter with converter assembly detects malfunctions in the drive motor inverter temperature sensor and its wiring.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P0AED1C Drive Motor Inverter Temperature Sensor "A" Circuit Voltage Out of Range Drive motor inverter temperature calculated by the EV control ECU is different from the actual temperature for 10 seconds or more, and the drive motor inverter temperature is excessively high.
(1 trip detection logic)
·

Inverter cooling system

·

Cooling fan system

·

Inverter with converter assembly

·

Wire harness or connector


Master Warning:
Comes on
EV A
P0AED1F Drive Motor Inverter Temperature Sensor "A" Circuit Intermittent Sudden change in drive motor inverter temperature sensor output or hunting:
Drive motor inverter temperature is high and either of the following conditions is met:
1.

Unusual sudden change in drive motor inverter temperature sensor output occurs and the offset continues for a certain period of time.*

2.

Unusual sudden change in drive motor inverter temperature sensor output occurs repeatedly.*


(1 trip detection logic)
·

Inverter cooling system

·

Cooling fan system

·

Inverter with converter assembly

·

Wire harness or connector


Master Warning:
Comes on
EV A

HINT:

*: If only DTC P0AED1F is output, a temperature sensor malfunction is more likely to be the cause than a sudden change in actual temperature.


Related Data List
DTC No. ECU Data List
P0AED1C
·

Motor Inverter Temperature

·

FC Air Compressor Inverter Temperature


P0AED1F

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Turn the ignition switch to ON (READY) and wait for 90 seconds or more.

2.

Drive the vehicle for approximately 10 minutes referring to the following freeze frame data or Data List items: "Vehicle Speed".

3.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

4.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the electric vehicle charger assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
P0AED1C or P0AED1F only is output, or DTCs except the ones in the table below are also output. A
Any of the following DTCs are also output. B


Relevant DTC
P0A9300 Inverter "A" Cooling System Performance
P0C7396 Motor Electronics Coolant Pump "A" Component Internal Failure
P314A31 Motor Electronics Coolant Pump "A" No Signal

HINT:

P0AED1C or P0AED1F may be output as a result of the malfunction indicated by the DTCs above.



Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A001C

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

3.CHECK COOLING SYSTEM

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK COOLING SYSTEM

NEXT

REPLACE INVERTER WITH CONVERTER ASSEMBLY