Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0D2D1C  Drive Motor "A" Inverter Voltage Sensor Voltage Out of Range  


DTC SUMMARY

MALFUNCTION DESCRIPTION


The EV control ECU detects a VH sensor malfunction.

The cause of this malfunction may be one of the following:

Inverter voltage sensor internal circuit malfunction
·

Voltage sensor malfunction

·

Motor generator control ECU (MG ECU) malfunction

·

Communication (wire harness) malfunction


High voltage system malfunction

Inverter with converter assembly malfunction



DESCRIPTION

Refer to the description for DTC P0D2D16.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0D2D16

The signal line from the inverter voltage (VH) sensor is connected to the MG ECU, which is built into the inverter with converter assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P0D2D1C Drive Motor "A" Inverter Voltage Sensor Voltage Out of Range Inverter voltage (VH) sensor performance malfunction:
When not boosting, difference between "VH-Voltage after Boosting" and "VL-Voltage before Boosting" is large and difference between "VH-Voltage after Boosting" and "Hybrid/EV Battery Voltage" is large.
(1 trip detection logic)
·

Inverter with converter assembly


Master Warning:
Comes on
EV A

Related Data List
DTC No. Data List
P0D2D1C
·

VL-Voltage before Boosting

·

VH-Voltage after Boosting

·

FCDC Output Voltage

·

Boost Ratio



CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Turn the ignition switch to ON (READY) with park (P).

2.

Confirm that the Data List item "Boost Ratio" is 0% when the accelerator pedal is not depressed. Check that the Data List items "VH-Voltage after Boosting" and "FCDC Output Voltage" are almost the same.

3.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

4.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




CAUTION / NOTICE / HINT

NOTICE:
·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK DTC OUTPUT (EV, EV BATTERY)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Powertrain > EV Battery > Trouble Codes
50001 398
Result:
Result Proceed to
P0D2D1C only is output, or DTCs except the ones in the table below are also output. A
DTCs of hybrid control system in the tables below are output. B
DTCs of hybrid battery system in the tables below are output. C


Malfunction Content System Relevant DTC
Microcomputer malfunction Hybrid control system P0A1B49 Drive Motor "A" Control Module Internal Electronic Failure
P060647 Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure
P1D8F47 FC Air Compressor Motor Control Module Watchdog/Safety MCU Failure
P1D8F49 FC Air Compressor Motor Control Module Internal Electronic Failure
P0A1B1F Drive Motor "A" Control Module Circuit Intermittent
Hybrid battery system P060B49 Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure
P060687 Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message
P060A47 Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A87 Hybrid/EV Battery Energy Control Module Processor from Monitoring Processor Missing Message
P060B16 Hybrid/EV Battery Energy Control Module A/D Processing Circuit Voltage Below Threshold
P0E2D00 Hybrid/EV Battery Energy Control Module Hybrid/EV Battery Monitor Performance
Power source circuit malfunction Hybrid control system P06D61C Sensor Reference Voltage "F" Circuit/Open Circuit Voltage Out of Range
P06E61C Sensor Power Supply "C" Circuit/Open Circuit Voltage Out of Range
Communication system malfunction Hybrid control system P312387 Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message
U011187 Lost Communication with Hybrid/EV Battery Energy Control Module "A" Missing Message
Sensor and actuator circuit malfunction Hybrid battery system P301A1C Hybrid Battery Stack 1 Cell Voltage Detection Voltage Out of Range
P1A001C Hybrid Battery Stack 2 Cell Voltage Detection Voltage Out of Range
P1AFD1C Flying Capacitor/Internal Control Module Hybrid/EV Battery Monitor Voltage Out of Range
System malfunction Hybrid control system P0D2D16 Drive Motor "A" Inverter Voltage Sensor "A" Circuit Voltage Below Threshold
P0D2D17 Drive Motor "A" Inverter Voltage Sensor "A" Circuit Voltage Above Threshold
P0E3116 DC/DC Converter Voltage Sensor "A" (VL) Circuit Voltage Below Threshold
P0E3117 DC/DC Converter Voltage Sensor "A" (VL) Circuit Voltage Above Threshold

HINT:
·

P0D2D1C may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





Post-procedure1

a.

Turn the ignition switch off.



A

REPLACE INVERTER WITH CONVERTER ASSEMBLY

B

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

C