Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P1CFA12  IGB Signal Circuit Short to Auxiliary Battery  


DESCRIPTION

The EV control ECU monitors the IGB signal received from the certification ECU (smart key ECU assembly). When an error is detected in the IGB signal, this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1CFA12 IGB Signal Circuit Short to Auxiliary Battery An IGB signal from the EV control ECU is on when the ignition switch is off.
(1 trip detection logic)
·

Wire harness or connector

·

EV control ECU

·

Certification ECU (smart key ECU assembly)


Master Warning:
Comes on
EV A

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 10 minutes or more.

3.

Turn the ignition switch to ON and turn the GTS on.

4.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

for LHD:
A165972E83
0.406,3.135 2.573,3.49 2.167,0.354 10 false Certification ECU (Smart Key ECU Assembly) 1.719,1.542 2.198,1.854 0.479,0.313 10 false IGB 2.094,1.542 2.385,1.854 0.292,0.313 10 false 3 4.979,1.531 5.271,1.781 0.292,0.25 10 false 18 5.24,1.531 5.646,1.802 0.406,0.271 10 false IGB 5.281,3.125 6.354,3.375 1.073,0.25 10 false EV Control ECU 5.281,2.948 6.115,3.146 0.833,0.198 10 false A8 0.427,2.969 0.833,3.24 0.406,0.271 10 false D86

for RHD:
A165972E85
0.406,3.135 2.573,3.49 2.167,0.354 10 false Certification ECU (Smart Key ECU Assembly) 1.719,1.542 2.198,1.854 0.479,0.313 10 false IGB 2.094,1.542 2.385,1.854 0.292,0.313 10 false 3 4.979,1.531 5.271,1.781 0.292,0.25 10 false 18 5.24,1.531 5.646,1.802 0.406,0.271 10 false IGB 5.427,2.948 6.5,3.198 1.073,0.25 10 false EV Control ECU 5.031,2.948 5.865,3.146 0.833,0.198 10 false D15 0.427,2.969 0.833,3.24 0.406,0.271 10 false D86

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)

OK

2.CHECK CONNECTOR CONNECTION CONDITION (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

NG

CONNECT SECURELY

2.CHECK CONNECTOR CONNECTION CONDITION (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Check the connector connection condition of the certification ECU (smart key ECU assembly).

OK:

The connector is connected securely and there are no contact problems.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (IGB TERMINAL VOLTAGE)

NG

CONNECT SECURELY

3.CHECK HARNESS AND CONNECTOR (IGB TERMINAL VOLTAGE)

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.
A478491C47
2.563,0.5 2.969,0.844 0.406,0.344 2.573,0.896 2.979,1.24 0.406,0.344 2.708,1.75 2.594,2.438 true 0.104,0.104 0.417,0.26 0.313,0.156 10 false *a 2.698,0.594 3.104,0.76 0.406,0.167 10 false A8 2.5,2.49 2.948,2.656 0.448,0.167 10 false IGB 2.667,0.99 3.073,1.156 0.406,0.167 10 false D15 3.031,0.604 3.25,0.802 0.219,0.198 10 false *A 3.031,1 3.25,1.198 0.219,0.198 10 false *B
*A for LHD
*B for RHD
*a Component with harness connected
(EV control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A8)Location & Routing

Click Connector(A8)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A8-18 (IGB) - Body ground Ignition switch off Below 1 V

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(D15)Location & Routing

Click Connector(D15)Instrument Panel>Instrument Panel Wire>EV Control ECU

D15-18 (IGB) - Body ground Ignition switch off Below 1 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

NG

4.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
4.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

Pre-procedure1

a.

Disconnect the D86 certification ECU (smart key ECU assembly) connector.


Procedure1

a.
A478491C47
2.563,0.5 2.969,0.844 0.406,0.344 2.573,0.896 2.979,1.24 0.406,0.344 2.708,1.75 2.594,2.438 true 0.104,0.104 0.417,0.26 0.313,0.156 10 false *a 2.698,0.594 3.104,0.76 0.406,0.167 10 false A8 2.5,2.49 2.948,2.656 0.448,0.167 10 false IGB 2.667,0.99 3.073,1.156 0.406,0.167 10 false D15 3.031,0.604 3.25,0.802 0.219,0.198 10 false *A 3.031,1 3.25,1.198 0.219,0.198 10 false *B
*A for LHD
*B for RHD
*a Component with harness connected
(EV control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A8)Location & Routing

Click Connector(A8)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A8-18 (IGB) - Body ground Ignitino switch off Below 1 V

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(D15)Location & Routing

Click Connector(D15)Instrument Panel>Instrument Panel Wire>EV Control ECU

D15-18 (IGB) - Body ground Ignitino switch off Below 1 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the D86 certification ECU (smart key ECU assembly) connector.



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR