Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P212012  Throttle/Pedal Position Sensor/Switch "D" Circuit Short to Auxiliary Battery  P212014  Throttle/Pedal Position Sensor/Switch "D" Circuit Short to Ground or Open  P21201C  Throttle/Pedal Position Sensor/Switch "D" Voltage Out of Range  P21201F  Throttle/Pedal Position Sensor/Switch "D" Circuit Intermittent  P212512  Throttle/Pedal Position Sensor/Switch "E" Circuit Short to Auxiliary Battery  P212514  Throttle/Pedal Position Sensor/Switch "E" Circuit Short to Ground or Open  P21251C  Throttle/Pedal Position Sensor/Switch "E" Voltage Out of Range  P21251F  Throttle/Pedal Position Sensor/Switch "E" Circuit Intermittent  P213800  Throttle/Pedal Position Sensor/Switch "D"/" E" Voltage Correlation  P21382B  Throttle/Pedal Position Sensor/Switch "D"/"E" Signal Cross Coupled  


DTC SUMMARY

MALFUNCTION DESCRIPTION


The EV control ECU calculates the accelerator pedal opening angle based on the output voltage of the main sensor (VPA) and sub sensor (VPA2) of the accelerator pedal sensor assembly. If the output voltage of either the main sensor (VPA) or sub sensor (VPA2) deviates, a malfunction will be detected.

The cause of this malfunction may be one of the following:

·

Accelerator pedal (with sensor) rod assembly malfunction

·

Wire harness or connector malfunction

·

EV control ECU malfunction



DESCRIPTION

The accelerator pedal position sensor is built into the accelerator pedal sensor assembly and detects how much the pedal is depressed. This is a non-contact sensor with Hall elements. There are 2 outputs from the sensor. One is used to detect the accelerator pedal position and the other is used as a confirmation to allow the detection of a malfunction in the sensor itself. Voltage is output from the accelerator pedal position sensor to terminals VPA and VPA2 of the EV control ECU. This voltage varies from 0 to 5 V in accordance with the accelerator pedal position. Terminal VPA2 is primarily used to detect a malfunction in the sensor itself. The EV control ECU determines the current accelerator pedal position and controls the hybrid control system based on signals received by terminals VPA and VPA2.

A484680E01
0.76,2.708 0.76,3.427 0.76,3.427 0.854,3.427 false 0.76,1.615 0.76,0.75 0.76,0.75 0.865,0.75 false 0.74,2.01 0.219,0.385 0.219,0.385 0.302,0.385 false 0.75,2.354 0.198,3.813 0.198,3.813 0.281,3.813 false 6.677,1.208 6.677,0.365 6.677,0.365 6.417,0.365 false 6.552,1.427 6.552,3.51 6.552,3.51 6.292,3.51 false 0.875,0.698 1.417,0.917 0.542,0.219 10 false Magnet 0.333,0.313 1.188,0.479 0.854,0.167 10 false Hall Element 0.333,3.74 1.188,3.906 0.854,0.167 10 false Hall Element 0.875,3.354 1.385,3.521 0.51,0.167 10 false Magnet 1.792,3.542 2.969,3.74 1.177,0.198 10 false EV Control ECU 2.823,1.771 3.969,2.323 1.146,0.552 10 false Accelerator Pedal Position Sensor Output Voltage (V) 4.094,0.688 6.313,0.865 2.219,0.177 10 false Accelerator Pedal Opening Angle (°) 4.396,4.094 6.708,4.271 2.313,0.177 10 false *1: Accelerator Pedal Fully Released 4.396,4.385 6.781,4.563 2.385,0.177 10 false *2: Accelerator Pedal Fully Depressed 0.198,4.063 1.323,4.396 1.125,0.333 10 false Accelerator Pedal Sensor Assembly 2.146,1.083 2.396,1.25 0.25,0.167 10 false 5 V 4.229,1.01 4.323,1.177 0.094,0.167 10 false 5 4.229,2.396 4.323,2.563 0.094,0.167 10 false 0 3.938,1.271 4.323,1.438 0.385,0.167 10 false 3.988 3.938,1.469 4.323,1.635 0.385,0.167 10 false 3.188 4.104,1.938 4.323,2.104 0.219,0.167 10 false 1.6 6.865,1.135 7.156,1.302 0.292,0.167 10 false 4.55 6.865,1.354 7.156,1.521 0.292,0.167 10 false 3.75 6.656,2.521 6.833,2.688 0.177,0.167 10 false 20 4.25,2.823 4.427,2.99 0.177,0.167 10 false *1 6.052,2.823 6.229,2.99 0.177,0.167 10 false *2 5.104,2.51 5.427,2.677 0.323,0.167 10 false 13.1 4.104,2.156 4.323,2.323 0.219,0.167 10 false 0.8 2.51,1.938 2.76,2.104 0.25,0.167 10 false 5 V 2.198,1.677 2.531,1.844 0.333,0.167 10 false AD 2.365,2.552 2.698,2.771 0.333,0.219 10 false AD 4.104,0.292 6.573,0.635 2.469,0.344 10 false VPA2: Malfunction Detection Sensor 4.854,3.448 6.385,3.656 1.531,0.208 10 false VPA: Control Sensor 1.365,1.229 1.979,1.427 0.615,0.198 10 false VCPA 1.385,1.563 2,1.76 0.615,0.198 10 false VPA 1.375,1.875 1.99,2.073 0.615,0.198 10 false EPA 1.344,2.115 1.958,2.313 0.615,0.198 10 false VCP2 1.344,2.438 1.958,2.635 0.615,0.198 10 false VPA2 1.333,2.76 1.719,2.927 0.385,0.167 10 false EPA2

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P212012 Throttle/Pedal Position Sensor/Switch "D" Circuit Short to Auxiliary Battery Short to +B in the main sensor circuit:
The main sensor voltage is 4.8 V or more for 2 seconds.
(1 trip detection logic)
·

Wire harness or connector

·

Accelerator pedal (with sensor) rod assembly

·

EV control ECU


Master Warning:
Comes on
EV A
P212014 Throttle/Pedal Position Sensor/Switch "D" Circuit Short to Ground or Open Open or short to ground in the main sensor circuit:
The main sensor voltage is 0.4 V or less for 0.5 seconds.
(1 trip detection logic)
·

Wire harness or connector

·

Accelerator pedal (with sensor) rod assembly

·

EV control ECU


Master Warning:
Comes on
EV A
P21201C Throttle/Pedal Position Sensor/Switch "D" Voltage Out of Range Internal malfunction in the main sensor:
Main sensor output changes rapidly (detected when there are no circuit malfunctions such as an open or short).
(1 trip detection logic)
·

Wire harness or connector

·

Accelerator pedal (with sensor) rod assembly

·

EV control ECU


Master Warning:
Comes on
EV A
P21201F Throttle/Pedal Position Sensor/Switch "D" Circuit Intermittent Main sensor circuit wiring malfunction or level is not stable:
Main sensor voltage is 0.4 V or less or 4.8 V or more for a certain period of time.
(Both of the following conditions are met: The main sensor voltage is 0.4 V or less for a certain period of time and 4.8 V or more for a certain period of time.)
(1 trip detection logic)
·

Wire harness or connector

·

Accelerator pedal (with sensor) rod assembly

·

EV control ECU


Master Warning:
Comes on
EV A
P212512 Throttle/Pedal Position Sensor/Switch "E" Circuit Short to Auxiliary Battery Short to +B in the sub sensor circuit:
Main sensor is normal and sub sensor voltage is 4.8 V or more for 2 seconds.
(1 trip detection logic)
·

Wire harness or connector

·

Accelerator pedal (with sensor) rod assembly

·

EV control ECU


Master Warning:
Comes on
EV A
P212514 Throttle/Pedal Position Sensor/Switch "E" Circuit Short to Ground or Open Open or short to ground in the sub sensor circuit:
The sub sensor voltage is 1.2 V or less for 0.5 seconds.
(1 trip detection logic)
·

Wire harness or connector

·

Accelerator pedal (with sensor) rod assembly

·

EV control ECU


Master Warning:
Comes on
EV A
P21251C Throttle/Pedal Position Sensor/Switch "E" Voltage Out of Range Internal malfunction of the sub sensor:
Sub sensor output changes rapidly (detected when there are no circuit malfunctions such as an open or short).
(1 trip detection logic)
·

Wire harness or connector

·

Accelerator pedal (with sensor) rod assembly

·

EV control ECU


Master Warning:
Comes on
EV A
P21251F Throttle/Pedal Position Sensor/Switch "E" Circuit Intermittent Sub sensor circuit wiring malfunction or level is not stable:
When the main sensor circuit is normal, the sub sensor voltage is 1.2 V or less or 4.8 V or more for a certain period of time.
(Both of the following conditions are met: Sub sensor voltage is 1.2 V or less for a certain period of time, and the main sensor is normal and sub sensor voltage is 4.8 V or more for a certain period of time.)
(1 trip detection logic)
·

Wire harness or connector

·

Accelerator pedal (with sensor) rod assembly

·

EV control ECU


Master Warning:
Comes on
EV A
P213800 Throttle/Pedal Position Sensor/Switch "D"/" E" Voltage Correlation Difference between the main sensor value and sub sensor value is large.
(1 trip detection logic)
·

Wire harness or connector

·

Accelerator pedal (with sensor) rod assembly

·

EV control ECU


Master Warning:
Comes on
EV A
P21382B Throttle/Pedal Position Sensor/Switch "D"/"E" Signal Cross Coupled Main or sub sensor circuit wiring malfunction:
The difference in voltage between the main sensor and sub sensor is 0.02 V or less, or a low output malfunction continues in both the main and sub sensors for a certain period of time.
(1 trip detection logic)
·

Wire harness or connector

·

Accelerator pedal (with sensor) rod assembly

·

EV control ECU


Master Warning:
Comes on
EV A

Related Data List
DTC No. Data List
P212012
·

Accelerator Position Sensor No. 1 Voltage %

·

Accelerator Position Sensor No. 2 Voltage %


P212014
P21201C
P21201F
P212512
P212514
P21251C
P21251F
P213800
P21382B

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 10 minutes or more.

3.

Wait for approximately 10 seconds with the ignition switch to ON (READY) and park (P) selected, then fully depress and release the accelerator pedal several times.

4.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

C383718E04
1.813,0.594 2.427,0.792 0.615,0.198 10 false VCPA 5.365,0.5 5.979,0.698 0.615,0.198 10 false VCPA 1.906,1.042 2.365,1.24 0.458,0.198 10 false VPA 5.365,0.938 5.823,1.135 0.458,0.198 10 false VPA 1.917,1.49 2.375,1.688 0.458,0.198 10 false EPA 5.365,1.375 5.823,1.573 0.458,0.198 10 false EPA 1.833,1.906 2.448,2.104 0.615,0.198 10 false VCP2 5.375,1.813 5.99,2.01 0.615,0.198 10 false VCP2 1.844,2.354 2.458,2.552 0.615,0.198 10 false VPA2 5.375,2.25 5.99,2.448 0.615,0.198 10 false VPA2 1.833,2.792 2.448,2.99 0.615,0.198 10 false EPA2 5.365,2.688 5.979,2.885 0.615,0.198 10 false EPA2 0.875,3.302 3.25,3.542 2.375,0.24 10 false Accelerator Pedal Sensor Assembly 0.896,3.135 1.208,3.333 0.313,0.198 10 false A1 5.135,0.479 5.448,0.677 0.313,0.198 10 false 6 5.094,0.917 5.406,1.115 0.313,0.198 10 false 35 5.135,1.792 5.448,1.99 0.313,0.198 10 false 5 5.094,1.354 5.406,1.552 0.313,0.198 10 false 27 5.115,2.25 5.427,2.448 0.313,0.198 10 false 33 5.104,2.677 5.417,2.875 0.313,0.198 10 false 25 6.135,0.469 6.375,0.646 0.24,0.177 10 false 5 V 2.302,0.49 2.458,0.688 0.156,0.198 10 false 4 2.302,0.927 2.458,1.125 0.156,0.198 10 false 6 2.302,1.354 2.458,1.552 0.156,0.198 10 false 5 2.302,1.802 2.458,2 0.156,0.198 10 false 1 2.302,2.24 2.458,2.438 0.156,0.198 10 false 3 2.302,2.677 2.458,2.875 0.156,0.198 10 false 2 5.323,3.313 6.521,3.521 1.198,0.208 10 false EV Control ECU 5.323,3.125 5.781,3.323 0.458,0.198 10 false A17

PROCEDURE

1.READ VALUE USING GTS (ACCELERATOR POSITION SENSOR NO. 1 VOLTAGE %, ACCELERATOR POSITION SENSOR NO. 2 VOLTAGE %)

Pre-procedure1

a.

None.


Procedure1

a.

Read the Data List.

Powertrain > EV > Data List
Tester Display
Accelerator Position Sensor No.1 Voltage %
Accelerator Position Sensor No.2 Voltage %
50003 397 23,24
HINT:

If the Data List updates slowly, perform measurement after selecting only the "Accelerator Position Sensor No.1 Voltage %" and "Accelerator Position Sensor No.2 Voltage %" items.


Standard:
Tester Display Accelerator Pedal Condition Specified Condition
Accelerator Position Sensor No. 1 Voltage % Not depressed 10 to 22%
Accelerator Position Sensor No. 2 Voltage % Not depressed 24 to 40%


Result:
Result Proceed to
The value of Accelerator Position Sensor No.1 Voltage % is between 10 and 22% and the value of Accelerator Position Sensor No.2 Voltage % is between 24 and 40% A
None of the above conditions are met B



Post-procedure1

a.

Turn the ignition switch off.



A

2.READ VALUE USING GTS (ACCELERATOR POSITION SENSOR NO. 1 VOLTAGE %, ACCELERATOR POSITION SENSOR NO. 2 VOLTAGE %)

B

4.CHECK CONNECTOR CONNECTION CONDITION (ACCELERATOR PEDAL SENSOR ASSEMBLY CONNECTOR)
2.READ VALUE USING GTS (ACCELERATOR POSITION SENSOR NO. 1 VOLTAGE %, ACCELERATOR POSITION SENSOR NO. 2 VOLTAGE %)

Pre-procedure1

a.

None.


Procedure1

a.

Read the Data List.

Powertrain > EV > Data List
Tester Display
Accelerator Position Sensor No.1 Voltage %
Accelerator Position Sensor No.2 Voltage %
50003 397 23,24
HINT:

If the Data List updates slowly, perform measurement after selecting only the "Accelerator Position Sensor No.1 Voltage %" and "Accelerator Position Sensor No.2 Voltage %" items.


Standard:
Tester Display Accelerator Pedal Condition Specified Condition
Accelerator Position Sensor No. 1 Voltage % Fully depressed 52 to 90%
Accelerator Position Sensor No. 2 Voltage % Fully depressed 68 to 99%


Result:
Result Proceed to
The value of Accelerator Position Sensor No.1 Voltage % is between 52 and 90% and the value of Accelerator Position Sensor No.2 Voltage % is between 68 and 90% A
None of the above conditions are met B



Post-procedure1

a.

Turn the ignition switch off.



A

3.READ VALUE USING GTS (ACCELERATOR POSITION SENSOR NO. 1 VOLTAGE %, ACCELERATOR POSITION SENSOR NO. 2 VOLTAGE %)

B

4.CHECK CONNECTOR CONNECTION CONDITION (ACCELERATOR PEDAL SENSOR ASSEMBLY CONNECTOR)
3.READ VALUE USING GTS (ACCELERATOR POSITION SENSOR NO. 1 VOLTAGE %, ACCELERATOR POSITION SENSOR NO. 2 VOLTAGE %)

Pre-procedure1

a.

None.


Procedure1

a.

Read the Data List.

Powertrain > EV > Data List
Tester Display
Accelerator Position Sensor No.1 Voltage %
Accelerator Position Sensor No.2 Voltage %
50003 397 23,24
HINT:

If the Data List updates slowly, perform measurement after selecting only the "Accelerator Position Sensor No.1 Voltage %" and "Accelerator Position Sensor No.2 Voltage %" items.


Standard:
Tester Display Accelerator Pedal Condition Specified Condition
Accelerator Position Sensor No. 1 Voltage % Not depressed → Fully depressed → Not depressed (Accelerator pedal should be operated slowly) Value changes progressively
Accelerator Position Sensor No. 2 Voltage % Not depressed → Fully depressed → Not depressed (Accelerator pedal should be operated slowly) Value changes progressively


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.



OK

NG

4.CHECK CONNECTOR CONNECTION CONDITION (ACCELERATOR PEDAL SENSOR ASSEMBLY CONNECTOR)
4.CHECK CONNECTOR CONNECTION CONDITION (ACCELERATOR PEDAL SENSOR ASSEMBLY CONNECTOR)
a.

Check the connector connections and contact pressure of the relevant terminals for the accelerator pedal sensor assembly connector.

A484675C01
0.25,0.115 0.563,0.313 0.313,0.198 10 true *A 3.74,0.094 4.052,0.292 0.313,0.198 10 true *B
*A for LHD *B for RHD


HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

The connectors are connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

5.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)

NG

CONNECT SECURELY

5.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)

OK

6.CHECK EV CONTROL ECU (CHECK VOLTAGE)

NG

CONNECT SECURELY

6.CHECK EV CONTROL ECU (CHECK VOLTAGE)

Pre-procedure1

a.

Disconnect the A1 accelerator pedal sensor assembly connector.


b.

Turn the ignition switch to ON.


Procedure1

a.
A380541C22
0.396,0.979 0.781,1.208 0.385,0.229 0.948,1.688 1.292,1.104 true 1.365,1.698 1.49,1.125 true 2.052,1.708 1.802,1.125 true 2.479,1.677 1.99,1.125 true 0.083,0.073 0.396,0.229 0.313,0.156 10 false *a 0.469,1.021 0.927,1.219 0.458,0.198 10 false A1 0.781,1.708 1.396,1.906 0.615,0.198 10 false VCP2 1.219,1.719 1.833,1.917 0.615,0.198 10 false EPA2 1.917,1.74 2.531,1.938 0.615,0.198 10 false VCPA 2.406,1.729 2.865,1.927 0.458,0.198 10 false EPA
*a Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A1)Location & Routing

Click Connector(A1)Instrument Panel>Front Compartment Main Wire>Accelerator Pedal Rod Assembly (with Sensor)

A1-4 (VCPA) - A1-5 (EPA) Ignition switch ON 4.5 to 5.5 V
A1-1 (VCP2) - A1-2 (EPA2) Ignition switch ON 4.5 to 5.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the A1 accelerator pedal sensor assembly connector.



OK

7.CHECK EV CONTROL ECU (CHECK RESISTANCE)

NG

9.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - ACCELERATOR PEDAL SENSOR ASSEMBLY)
7.CHECK EV CONTROL ECU (CHECK RESISTANCE)

Pre-procedure1

a.

Disconnect the A1 accelerator pedal sensor assembly connector.


Procedure1

a.
A380541C28
0.396,0.979 0.781,1.208 0.385,0.229 1.51,1.708 1.656,1.125 true 0.938,1.688 1.49,1.125 true 2.833,1.719 2.125,1.125 true 2.24,1.708 1.99,1.125 true 0.083,0.073 0.396,0.229 0.313,0.156 10 false *a 0.5,1.021 0.958,1.219 0.458,0.198 10 false A1 1.302,1.781 1.917,1.979 0.615,0.198 10 false VPA2 0.688,1.76 1.104,1.979 0.417,0.219 10 false EPA2 2.771,1.771 3.146,1.99 0.375,0.219 10 false VPA 2.135,1.771 2.594,1.969 0.458,0.198 10 false EPA
*a Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A1)Location & Routing

Click Connector(A1)Instrument Panel>Front Compartment Main Wire>Accelerator Pedal Rod Assembly (with Sensor)

A1-6 (VPA) - A1-5 (EPA) Ignition switch off 28.00 to 41.61 kΩ
A1-3 (VPA2) - A1-2 (EPA2) Ignition switch off 28.00 to 41.61 kΩ


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A1 accelerator pedal sensor assembly connector.



OK

REPLACE ACCELERATOR PEDAL (WITH SENSOR) ROD ASSEMBLY

NG

8.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - ACCELERATOR PEDAL SENSOR ASSEMBLY)
8.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - ACCELERATOR PEDAL SENSOR ASSEMBLY)

Pre-procedure1

a.

Disconnect the A17 EV Control ECU connector.


b.

Disconnect the A1 accelerator pedal sensor assembly connector.


c.

Turn the ignition switch to ON.


Procedure1

a.
A480893C02
2.052,0.094 2.5,0.427 0.448,0.333 1.458,2.552 1.896,2.885 0.438,0.333 1.469,1.969 2.063,1.865 true 2.063,1.938 1.885,2.313 true 2.219,2.354 2.156,1.938 true 2.667,2.25 2.156,1.865 true 0.792,4.135 1.396,3.521 true 1.25,4.125 1.583,3.5 true 1.854,4.104 1.896,3.521 true 2.365,4.115 2.063,3.51 true 0.125,0.135 0.438,0.292 0.313,0.156 10 false *a 0.156,2.458 0.469,2.615 0.313,0.156 10 false *b 2.177,0.198 2.635,0.396 0.458,0.198 10 false A17 1.604,2.646 2.063,2.844 0.458,0.198 10 false A1 1.094,4.167 1.708,4.365 0.615,0.198 10 false VPA2 0.604,4.167 1.219,4.365 0.615,0.198 10 false EPA2 1.76,4.156 2.375,4.354 0.615,0.198 10 false EPA 2.313,4.156 2.771,4.354 0.458,0.198 10 false VPA 2.708,2.219 3.323,2.417 0.615,0.198 10 false EPA2 1.219,1.938 1.833,2.135 0.615,0.198 10 false EPA 1.771,2.344 2.229,2.542 0.458,0.198 10 false VPA 2.104,2.406 2.719,2.604 0.615,0.198 10 false VPA2
*a Rear view of wire harness connector
(to EV Control ECU)
*b Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A17)Location & Routing

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A17-35 (VPA) - Body ground Ignition switch ON Below 1 V
A17-33 (VPA2) - Body ground Ignition switch ON Below 1 V
A17-27 (EPA) - Body ground Ignition switch ON Below 1 V
A17-25 (EPA2) - Body ground Ignition switch ON Below 1 V


NOTICE:

Turning the ignition switch to ON with the EV control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



b.

Turn the ignition switch off.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A17,A1)Location & Routing

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(A1)Instrument Panel>Front Compartment Main Wire>Accelerator Pedal Rod Assembly (with Sensor)

A17-35 (VPA) - A1-6 (VPA) Ignition switch off Below 1 Ω
A17-27 (EPA) - A1-5 (EPA) Ignition switch off Below 1 Ω
A17-33 (VPA2) - A1-3 (VPA2) Ignition switch off Below 1 Ω
A17-25 (EPA2) - A1-2 (EPA2) Ignition switch off Below 1 Ω
A17-35 (VPA) or A1-6 (VPA) - Body ground and other terminals Ignition switch off 10 kΩ or higher
A17-27 (EPA) or A1-5 (EPA) - Body ground and other terminals Ignition switch off 10 kΩ or higher
A17-33 (VPA2) or A1-3 (VPA2) - Body ground and other terminals Ignition switch off 10 kΩ or higher
A17-25 (EPA2) or A1-2 (EPA2) - Body ground and other terminals Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A1 accelerator pedal sensor assembly connector.


b.

Reconnect the A17 EV Control ECU connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - ACCELERATOR PEDAL SENSOR ASSEMBLY)

Pre-procedure1

a.

Disconnect the A17 EV control ECU connector.


b.

Disconnect the A1 accelerator pedal sensor assembly connector.


c.

Turn the ignition switch to ON.


Procedure1

a.
A480893C04
2.052,0.115 2.51,0.438 0.458,0.323 1.458,2.552 1.906,2.854 0.448,0.302 1.479,1.979 2.073,1.875 true 2.135,1.729 2.76,2.094 true 1.74,1.729 2.063,1.729 true 2.323,2.354 2.156,1.865 true 0.792,4.135 1.26,3.531 true 1.25,4.125 1.448,3.542 true 1.854,4.104 1.75,3.531 true 2.365,4.115 1.917,3.531 true 0.125,0.135 0.438,0.292 0.313,0.156 10 false *a 0.156,2.458 0.469,2.615 0.313,0.156 10 false *b 1.375,1.677 1.833,1.875 0.458,0.198 10 false VCPA 1.219,1.938 1.833,2.135 0.615,0.198 10 false EPA 2.177,2.406 2.792,2.604 0.615,0.198 10 false EPA2 2.813,2.063 3.375,2.26 0.563,0.198 10 false VCP2 2.188,0.229 2.646,0.427 0.458,0.198 10 false A17 1.615,2.625 2.073,2.823 0.458,0.198 10 false A1 1.094,4.167 1.708,4.365 0.615,0.198 10 false EPA2 0.604,4.167 1.219,4.365 0.615,0.198 10 false VCP2 1.76,4.156 2.375,4.354 0.615,0.198 10 false VCPA 2.313,4.156 2.771,4.354 0.458,0.198 10 false EPA
*a Rear view of wire harness connector
(to EV Control ECU)
*b Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A17)Location & Routing

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A17-6 (VCPA) - Body ground Ignition switch ON Below 1 V
A17-27 (EPA) - Body ground Ignition switch ON Below 1 V
A17-5 (VCP2) - Body ground Ignition switch ON Below 1 V
A17-25 (EPA2) - Body ground Ignition switch ON Below 1 V


NOTICE:

Turning the ignition switch to ON with the EV control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



b.

Turn the ignition switch off.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A17,A1)Location & Routing

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(A1)Instrument Panel>Front Compartment Main Wire>Accelerator Pedal Rod Assembly (with Sensor)

A17-6 (VCPA) - A1-4 (VCPA) Ignition switch off Below 1 Ω
A17-27 (EPA) - A1-5 (EPA) Ignition switch off Below 1 Ω
A17-5 (VCP2) - A1-1 (VCP2) Ignition switch off Below 1 Ω
A17-25 (EPA2) - A1-2 (EPA2) Ignition switch off Below 1 Ω
A17-6 (VCPA) or A1-4 (VCPA) - Body ground and other terminals Ignition switch off 10 kΩ or higher
A17-27 (EPA) or A1-5 (EPA) - Body ground and other terminals Ignition switch off 10 kΩ or higher
A17-5 (VCP2) or A1-1 (VCP2) - Body ground and other terminals Ignition switch off 10 kΩ or higher
A17-25 (EPA2) or A1-2 (EPA2) - Body ground and other terminals Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A1 accelerator pedal sensor assembly connector.


b.

Reconnect the A17 EV control ECU connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR