Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P253012  IG2 Signal Circuit Short to Auxiliary Battery  


DESCRIPTION

The EV control ECU compares the IG2 signal to the IG control status signal sent from the certification ECU (smart key ECU assembly) to detect a stuck on malfunction of the IG2 signal.

HINT:

If DTC P253012 is stored, the ignition switch will turn off (READY off).


DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P253012 IG2 Signal Circuit Short to Auxiliary Battery The IG2 signal of the EV control ECU and the IG control status signal sent from the certification ECU (smart key ECU assembly) do not match.
(1 trip detection logic)
·

Auxiliary battery

·

Certification ECU (smart key ECU assembly)

·

EV control ECU

·

IG2 P relay

·

Wire harness or connector


Master Warning:
Comes on
EV A

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 10 minutes or more.

3.

Turn the ignition switch to ON and wait for 15 seconds or more.

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

6.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

A481435E01
2.781,2.208 5.521,2.396 2.74,0.188 10 false Luggage Room Relay Block 6.083,1.906 7.125,2.135 1.042,0.229 10 false EV Control ECU 6.156,0.51 6.615,0.708 0.458,0.198 10 false IG2 5.792,0.604 6.25,0.802 0.458,0.198 10 false A16 5.865,0.406 6.021,0.604 0.156,0.198 10 false 7 4.063,0.75 4.813,0.948 0.75,0.198 10 false IG2 P NO.1 4.917,0.615 5.125,0.802 0.208,0.188 10 false 6 3.313,1.813 3.75,1.99 0.438,0.177 10 false IG2 P 1.438,0.75 2.271,0.906 0.833,0.156 10 false R/B RR# 2 2.427,0.604 2.74,0.802 0.313,0.198 10 false 6C 2.469,0.406 2.625,0.604 0.156,0.198 10 false 1 6.146,1.417 6.604,1.615 0.458,0.198 10 false E01 5.865,1.219 6.021,1.417 0.156,0.198 10 false 3 2.469,1.406 2.677,1.594 0.208,0.188 10 false 6 4.917,1.417 5.125,1.604 0.208,0.188 10 false 6 1.302,1.583 2.25,1.76 0.948,0.177 10 false LUG-IG1 NO.1 0.083,1.417 0.979,1.781 0.896,0.365 10 false From LUG-IG1 NO.1 Relay 4.396,0.469 4.552,0.667 0.156,0.198 10 false 2 4.156,0.479 4.313,0.677 0.156,0.198 10 false 1 5.792,1.406 6.25,1.604 0.458,0.198 10 false A17 2.938,0.708 3.146,0.896 0.208,0.188 10 false 3 3.844,0.729 4.052,0.917 0.208,0.188 10 false 5 2.927,1.521 3.135,1.708 0.208,0.188 10 false 2 3.833,1.521 3.99,1.719 0.156,0.198 10 false 1 0.073,0.594 1.073,1.063 1,0.469 10 false From Auxiliary Battery

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK AUXILIARY BATTERY VOLTAGE

Pre-procedure1

a.

Turn the ignition switch off and turn on the high beam headlights for 30 seconds. This will remove the surface charge from the auxiliary battery.


b.

Turn the high beam headlights off.


Procedure1

a.

Measure the auxiliary battery voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Positive (+) auxiliary battery terminal - Negative (-) auxiliary battery terminal
·

20°C (68°F)

·

Ignition switch off


12.0 V or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

2.CLEAR DTC

NG

8.CHARGE OR REPLACE AUXILIARY BATTERY
2.CLEAR DTC

NEXT

3.CHECK DTC OUTPUT (EV)
3.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

Turn the ignition switch to ON and wait for 15 seconds or more.


b.

Turn the ignition switch off and wait for 10 minutes or more.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
P253012 is output A
P253012 is not output B



Post-procedure1

a.

Turn the ignition switch off.



A

4.CHECK DTC OUTPUT (EV)

B

4.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
U012987, U014087, U015187, U016487 or U117087 is output A
U012987, U014087, U015187, U016487 or U117087 is not output B



Post-procedure1

a.

Turn the ignition switch off.



A

5.CHECK EV CONTROL ECU

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

5.CHECK EV CONTROL ECU

Pre-procedure1

a.
A480872C02
1.469,0.646 1.906,1 0.438,0.354 2.042,0.635 2.479,0.99 0.438,0.354 2.292,2.302 2.646,2.969 true 1.448,2.292 1.271,2.948 true 0.083,0.094 0.396,0.25 0.313,0.156 10 false *a 1.573,0.771 2.031,0.969 0.458,0.198 10 false A16 2.156,0.75 2.615,0.948 0.458,0.198 10 false A17 2.552,3 3.01,3.198 0.458,0.198 10 false E01 1.167,2.99 1.625,3.188 0.458,0.198 10 false IG2
*a Rear view of wire harness connector
(to EV Control ECU)


Disconnect the A16 and A17 EV Control ECU connectors.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A16,A17)Location & Routing

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A16-7 (IG2) - A17-3 (E01) Ignition switch off Below 9 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A16 and A17 EV Control ECU connectors.



OK

NG

6.INSPECT IG2 P RELAY
6.INSPECT IG2 P RELAY

Pre-procedure1

a.
A481455C02
1.208,1.188 1.396,0.75 1.396,0.75 1.542,0.75 true 0.073,0.073 0.385,0.271 0.313,0.198 10 false *1 1.604,0.688 1.917,0.885 0.313,0.198 10 false *2
*1 Luggage Room Relay Block
*2 IG2 P relay


Remove the IG2 P relay from the luggage room relay block.


Procedure1

a.
B060778N75
2.51,1.625 2.844,1.625 true 2.521,1.125 2.854,1.125 true 2.615,0.583 2.792,0.271 2.792,0.271 2.948,0.271 true 2.021,0.573 1.865,0.26 1.865,0.26 1.719,0.26 true 2.896,1.552 3.406,2.167 0.51,0.615 10 true 3 2.906,1.042 3.104,1.24 0.198,0.198 10 false 5 3.01,0.177 3.208,0.375 0.198,0.198 10 false 2 1.573,0.177 1.771,0.375 0.198,0.198 10 false 1 1.219,0.76 1.417,0.958 0.198,0.198 10 false 5 1.229,1.302 1.427,1.5 0.198,0.198 10 false 2 0.208,0.76 0.417,0.927 0.208,0.167 10 false 3 0.219,1.302 0.417,1.5 0.198,0.198 10 false 1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the IG2 P relay.



OK

7.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - LUGGAGE ROOM RELAY BLOCK)

NG

REPLACE IG2 P RELAY

7.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - LUGGAGE ROOM RELAY BLOCK)

Pre-procedure1

a.

Disconnect the A16 EV control ECU connector.


b.
A481455C02
1.208,1.188 1.396,0.75 1.396,0.75 1.542,0.75 true 0.073,0.073 0.385,0.271 0.313,0.198 10 false *1 1.604,0.688 1.917,0.885 0.313,0.198 10 false *2
*1 Luggage Room Relay Block
*2 IG2 P relay


Remove the IG2 P relay from the luggage room relay block.


Procedure1

a.
A478494C01
1.448,0.573 1.917,0.958 0.469,0.385 1.323,2.844 1.448,2.292 true 0.188,0.167 0.5,0.323 0.313,0.156 10 false *a 1.583,0.698 2.042,0.896 0.458,0.198 10 false A16 1.208,2.875 1.667,3.073 0.458,0.198 10 false IG2
*a Rear view of wire harness connector
(to EV Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A16)Location & Routing

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A16-7 (IG2) - Body ground Ignition switch off 1 V or less


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the IG2 P relay.


b.

Reconnect the A16 EV control ECU connector.



OK

CHECK FOR INTERMITTENT PROBLEMS
a.

Check for intermittent problems.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS

i.

Check the connection and terminal contact pressure of the connectors and wire harnesses between the EV control ECU and the passenger side junction block assembly.


ii.

When the ignition switch is ON (READY), jiggle the connectors and wire harnesses between the EV control ECU and the passenger side junction block assembly.




NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHARGE OR REPLACE AUXILIARY BATTERY
a.

Charge or replace the auxiliary battery.


Result:
Proceed to
NEXT



NEXT

2.CLEAR DTC