Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P26009E  Motor/Generator Coolant Pump "A" Control Circuit Stuck On  


DESCRIPTION

Refer to the description for DTC P260031.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P260031

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P26009E Motor/Generator Coolant Pump "A" Control Circuit Stuck On When the OIL PMP MTR relay is off, the NOPM input pulse signal is received.
(1 trip detection logic)
·

OIL PMP MTR relay

·

EV control ECU

·

Wire harness or connector


Master Warning:
Comes on
EV A

Related Data List
DTC No. Data List
P26009E
·

Target Motor/Generator Cooling Oil Pump Motor Duty

·

Motor/Generator Cooling Oil Pump Motor Revolution

·

Motor/Generator Cooling Oil Pump Motor Power Relay Request



HINT:

The oil pump with motor assembly cannot be activated only with the OIL PMP MTR relay on. It is activated after receiving the command signals (OPM1) from the EV control ECU.


CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Enter the following menus: Powertrain / EV / Active Test / Control the Motor/Generator Cooling Oil Pump.

3.

According to the display on the GTS, perform the Active Test and set the duty to 90%.

HINT:

The Active Test cannot be performed if the duty ratio is set to 50% or lower or 95% or higher, or if the ambient temperature is -11°C (12.2°F) or lower.


4.

According to the display on the GTS, read the Data List and check that the value of "Motor/Generator Cooling Oil Pump Motor Revolution" is between 450 rpm and 7000 rpm.

5.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

6.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for DTC P260031.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P260031

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (L TERMINAL VOLTAGE)

Pre-procedure1

a.
A480833

Disconnect the G155 oil pump with motor assembly connector.


b.

Turn the ignition switch to ON.


Procedure1

a.
A459452C08
1.521,0.375 1.979,0.74 0.458,0.365 2.438,1.729 2.104,1.198 true 0.219,0.104 0.51,0.344 0.292,0.24 10 false *a 1.604,0.5 2.021,0.781 0.417,0.281 10 false G155 2.438,1.781 2.781,2.021 0.344,0.24 10 false L
*a Front view of wire harness connector
(to Oil Pump with Motor Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(G155)Location & Routing

Click Connector(G155)Body>Floor Wire / No. 3 Floor Wire>Oil Pump with Motor Assembly

G155-4 (L) - Body ground Ignition switch ON Below 1 V


NOTICE:

Turning the ignition switch to ON with the oil pump with motor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the G155 oil pump with motor assembly connector.



OK

2.INSPECT RELAY (OIL PMP MTR)

NG

3.CHECK HARNESS AND CONNECTOR (OIL PUMP WITH MOTOR ASSEMBLY - OIL PMP MTR RELAY)
2.INSPECT RELAY (OIL PMP MTR)

Pre-procedure1

a.
A481442C01
2.51,2.844 2.313,2.229 true 0.115,0.083 0.427,0.281 0.313,0.198 10 false *1 2.49,2.896 2.802,3.094 0.313,0.198 10 false *2
*1 Luggage Room Relay Block
*2 OIL PMP MTR Relay


Remove the OIL PMP MTR relay from the luggage room relay block.


Procedure1

a.
A188757E20
1.906,0.302 2.094,0.302 2.094,0.302 2.146,0.563 false 3.031,0.302 2.813,0.302 2.813,0.302 2.708,0.563 false 2.646,1.115 3.104,1.115 false 2.646,1.604 3.104,1.604 false 0.365,0.771 0.521,0.969 0.156,0.198 10 3 1.813,0.24 1.969,0.406 0.156,0.167 10 1 1.302,1.292 1.458,1.49 0.156,0.198 10 2 0.354,1.302 0.51,1.469 0.156,0.167 10 1 3.094,0.24 3.25,0.438 0.156,0.198 10 2 1.302,0.76 1.458,0.958 0.156,0.198 10 5 3.177,1.031 3.333,1.229 0.156,0.198 10 5 3.177,1.521 3.333,1.719 0.156,0.198 10 3

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the OIL PMP MTR relay.



OK

NG

REPLACE RELAY (OIL PMP MTR)

3.CHECK HARNESS AND CONNECTOR (OIL PUMP WITH MOTOR ASSEMBLY - OIL PMP MTR RELAY)

Pre-procedure1

a.
A480833

Disconnect the G155 oil pump with motor assembly connector.


b.

Remove the OIL PMP MTR relay from the luggage room relay block.


c.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

A481444C01
1.563,0.646 2.052,1.031 0.49,0.385 2.042,1.417 2.229,1.875 true 3.594,0.188 3.906,0.344 0.313,0.156 10 false *1 5.385,2.104 5.698,2.26 0.313,0.156 10 false *2 0.344,0.188 0.656,0.344 0.313,0.156 10 false *a 1.656,0.781 2.115,0.979 0.458,0.198 10 false G155 2.208,1.958 2.365,2.156 0.156,0.198 10 false L
*1 Luggage Room Relay Block *2 OIL PMP MTR Relay
*a Front view of wire harness connector
(to Oil Pump with Motor Assembly)
- -


Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(G155)Location & Routing

Click Connector(G155)Body>Floor Wire / No. 3 Floor Wire>Oil Pump with Motor Assembly

G155-4 (L) or 5 (OIL PMP relay holder) - Body ground and other terminals Ignition switch ON Below 1 V


NOTICE:
·

Do not apply excessive force when using the probes of the tester to perform the inspection. If excessive force is used, the terminals will be damaged.

·

Turning the ignition switch to ON with the oil pump with motor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Install the OIL PMP MTR relay.


c.

Reconnect the G155 oil pump with motor assembly connector.



OK

4.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - OIL PMP MTR RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - OIL PMP MTR RELAY)

Pre-procedure1

a.

Disconnect the G14*1 or A14*2 EV control ECU connector.

*1: for LHD

*2: for RHD


b.

Remove the OIL PMP MTR relay from the luggage room relay block.


c.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

A481446C06
0.625,0.135 1.042,0.479 0.417,0.344 0.625,0.521 1.042,0.865 0.417,0.344 1.125,2.417 0.906,2.01 true 0.719,0.219 1.177,0.417 0.458,0.198 10 false G14 1.125,2.438 1.74,2.635 0.615,0.198 10 false OPM2 3.729,0.115 4.042,0.271 0.313,0.156 10 false *1 5.479,2.094 5.792,2.25 0.313,0.156 10 false *2 0.188,0.188 0.5,0.344 0.313,0.156 10 false *a 0.719,0.625 1.177,0.823 0.458,0.198 10 false A14 1.083,0.219 1.542,0.417 0.458,0.198 10 false *A 1.094,0.604 1.552,0.802 0.458,0.198 10 false *B
*A for LHD *B for RHD
*1 Luggage Room Relay Block *2 OIL PMP MTR relay
*a Rear view of wire harness connector
(to EV Control ECU)
- -


Standard Voltage:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(G14)Location & Routing

Click Connector(G14)Instrument Panel>Floor Wire>EV Control ECU

G14-9 (OPM2) or 1 (OIL PMP MTR relay holder) - Body ground and other terminals Ignition switch ON Below 1 V

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A14)Location & Routing

Click Connector(A14)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A14-9 (OPM2) or 1 (OIL PMP MTR relay holder) - Body ground and other terminals Ignition switch ON Below 1 V


NOTICE:
·

Do not apply excessive force when using the probes of the tester to perform the inspection. If excessive force is used, the terminals will be damaged.

·

Turning the ignition switch to ON with the oil pump with motor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Install the OIL PMP MTR relay.


c.

Reconnect the G14*1 or A14*2 EV control ECU connector.

*1: for LHD

*2: for RHD



OK

REPLACE RELAY (OIL PMP MTR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR