Home › Engine / Hybrid System › FUEL › FUEL SYSTEM
RM37H0E _51 Engine / Hybrid System _097300 FUEL _0465031 FUEL SYSTEM A

FUEL  FUEL SYSTEM  PRESSURE RELEASE OPERATION  


CAUTION / NOTICE / HINT

CAUTION:
·
A477349

Work procedures must be performed in an area with good ventilation (airflow) where hydrogen gas will not accumulate, and flames or other things that could act as ignition sources must not be present.

·

Accumulated hydrogen gas could ignite, resulting in a serious accident.

·
A477350C01
1.083,1.229 1.406,0.833 1.406,0.833 1.573,0.833 false 1.604,0.75 1.854,0.927 0.25,0.177 10 true *a
*a When inside of piping is pressurized


Do not install or remove any hydrogen system components without first performing depressurization procedures.

·

The highly pressurized hydrogen gas inside the hydrogen tank assembly could blow out, resulting in a serious accident.

·
A477351C01
1.083,0.271 1.323,0.469 0.24,0.198 10 true *a
*a Manual Valve Open


Do not perform depressurization procedures when the manual valve of the hydrogen tank assembly is open.

·

The highly pressurized hydrogen gas inside the hydrogen tank assembly could blow out, resulting in a serious accident.

·
A477352

When performing depressurization, do not perform procedures by hand without wearing protective glasses and gloves.

·

The highly pressurized hydrogen gas inside the hydrogen tank assembly could blow out, resulting in a serious accident.

·
A477353C01
1.302,0.396 1.135,0.646 1.135,0.646 1.135,0.813 true 1.073,0.844 1.302,1 0.229,0.156 10 true *a
*a After depressurization procedures, the high pressure piping union nut that is loosened first.


After performing depressurization procedures, when first loosening the union nut of the high pressure hydrogen piping, do not loosen the union nut by hand without wearing protective glasses and gloves.

·

Even when depressurization procedures are performed, the pressurized hydrogen gas inside the high pressure hydrogen piping cannot be completely depressurized, so the highly pressurized hydrogen gas remaining in the high pressure hydrogen piping could blow out, resulting in a serious accident.

·
A359853

When opening the tank shut valve and applying pressure to SST (hydrogen venting tool), stay away from SST (flexible hose).

·

If SST (flexible hose) comes off, you could be struck by the loose end of SST (flexible hose), causing a serious accident.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

Place signs [HIGH PRESSURE GAS WORK IN PROGRESS - DO NOT TOUCH!], etc. to warn other technicians to be cautious. (An example sign is included, so make a copy and use it.)

A355341E01
0.552,8.167 6.667,8.51 6.115,0.344 10 false Place signs [HIGH PRESSURE GAS WORK IN PROGRESS - DO NOT TOUCH!], etc. to warn other technicians to be cautious. (An example sign is included, so make a copy and use it.)

·

When performing depressurization, do not open or close any parts of the hydrogen gas piping except for the following:

- Adjustment bolt of the hydrogen tank assembly manual valve

- Tank shut valve of the hydrogen tank assembly

- No. 1 hydrogen supply regulator plug

·

When installing or removing the hydrogen tank assembly, high pressure hydrogen piping, hydrogen inlet receptacle, hydrogen tank tube joint assembly or hydrogen supply regulator, to prevent strain such as twisting from being applied to the high pressure hydrogen piping.

·

Even when not removing or installing the high pressure hydrogen piping, be careful not to pull or otherwise apply strain to the high pressure hydrogen piping.

·

When reusable parts such as the hydrogen tank assembly valve portion, hydrogen inlet receptacle, hydrogen tank tube joint assembly and hydrogen supply regulator have been removed, to protect the seal portions and threaded portions from damage as well as to prevent foreign matter such as dust and metal fragments from entering through openings, cover these areas with protective tape.

·

Do not use packing tape, or any other tape that will leave residue on parts, as protective tape.

·
A339304C10
0.719,0.458 1.021,0.667 false 1.198,0.927 1.417,1.729 1.417,1.729 1.177,1.26 true 1.854,0.74 2,1.823 2,1.823 1.677,1.458 true 0.51,0.375 0.823,0.531 0.313,0.156 10 false *a 1.365,1.781 1.583,1.948 0.219,0.167 10 false *b 1.917,1.854 2.229,2.01 0.313,0.156 10 false *c
*a Protective Tape
*b Seal Portion
*c Threaded Portion


Protect seal portions and threaded portions as shown in the illustration.

·

To protect the seal portions and threaded portions from damage or contamination by foreign matter, remove the protective tape immediately before installation.

·

When reassembling components that have been removed, make sure that there is no foreign matter adhering to the openings.

·

After installing high pressure hydrogen system components, first perform primary leak inspection with low pressure nitrogen gas, and then perform secondary leak inspection.

·
A479186C01
2.396,0.635 2.979,0.635 true 1.698,1.667 2.281,1.667 true 3,0.552 3.313,0.75 0.313,0.198 10 false *a 2.313,1.594 2.625,1.792 0.313,0.198 10 false *b
*a Atmosphere Ventilation Hole Cap
*b Relief Valve


Do not insert any sharp objects into the relief valve of the hydrogen supply regulator.

·

Do not remove the atmosphere ventilation hole cap of the hydrogen supply regulator.

·

When the vehicle is parked with the ignition switch off, if the FC control ECU judges that the FC stack temperature will go below 0°C (32°F), it activates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds and drains water from the FC stack assembly. When performing inspection or repairs with the ignition switch off (not on (IG) or on (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work.

·

When frost has formed on the hydrogen tank assembly or piping, water droplets may be formed when the frost begins to melt. If water droplets enter the tank or piping, it could result in blockage of the hydrogen piping, so do not allow water droplets to enter the tank or piping.



Hide 58404B 2.REMOVE REAR NO. 4 FLOOR BOARD SUB-ASSEMBLY

Hide 58403L 3.REMOVE REAR NO. 3 FLOOR BOARD SUB-ASSEMBLY

Hide 58402K 4.REMOVE NO. 2 FLOOR BOARD SUB-ASSEMBLY

Hide 57628E 5.REMOVE REAR FLOOR SIDE MEMBER COVER LH

Hide 58398F 6.REMOVE NO. 1 FLOOR UNDER COVER

Hide 17DB3 7.REMOVE NO. 3 FC EXHAUST PIPE

Hide 8. PRESSURE RELEASE OPERATION (for Low Pressure and Medium Pressure)

a.
A479195C02
1.479,2.948 1.323,2.948 1.323,2.948 1.052,2.844 true 2.688,3.052 2.688,2.792 true 1.5,2.875 1.813,3.031 0.313,0.156 10 false *c 0.906,1.969 1.219,2.125 0.313,0.156 10 false *a 2.594,1.969 2.906,2.125 0.313,0.156 10 false *b 2.635,3.073 2.948,3.229 0.313,0.156 10 false *c 1.24,3.135 1.583,3.365 0.344,0.229 10 false *d
*a Manual Valve Open
*b Manual Valve Closed
*c Adjustment Bolt
*d Clockwise


Using an 8 mm hexagon socket wrench, rotate the adjustment bolt clockwise to close the manual valve of the No. 1 hydrogen tank assembly.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:
·

The manual valve shuts off the pressure from the hydrogen tank assembly, so be careful not to damage the hexagonal portion.

·

If the hexagonal portion has been damaged, the No. 1 hydrogen tank assembly must be replaced.




b.
A479196C02
1.479,2.948 1.323,2.948 1.323,2.948 1.052,2.844 true 2.688,3.052 2.688,2.792 true 1.5,2.875 1.813,3.031 0.313,0.156 10 false *c 0.906,1.969 1.219,2.125 0.313,0.156 10 false *a 2.594,1.969 2.906,2.125 0.313,0.156 10 false *b 2.635,3.073 2.948,3.229 0.313,0.156 10 false *c 1.25,3.135 1.594,3.365 0.344,0.229 10 false *d
*a Manual Valve Open
*b Manual Valve Closed
*c Adjustment Bolt
*d Clockwise


Using an 8 mm hexagon socket wrench, rotate the adjustment bolt clockwise to close the manual valve of the No. 2 hydrogen tank assembly.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:
·

The manual valve shuts off the pressure from the hydrogen tank assembly, so be careful not to damage the hexagonal portion.

·

If the hexagonal portion has been damaged, the No. 2 hydrogen tank assembly must be replaced.




c.
A479197C02
1.479,2.948 1.323,2.948 1.323,2.948 1.052,2.844 true 2.688,3.052 2.688,2.792 true 1.5,2.875 1.813,3.031 0.313,0.156 10 false *c 0.906,1.969 1.219,2.125 0.313,0.156 10 false *a 2.594,1.969 2.906,2.125 0.313,0.156 10 false *b 2.635,3.073 2.948,3.229 0.313,0.156 10 false *c 1.24,3.135 1.583,3.365 0.344,0.229 10 false *d
*a Manual Valve Open
*b Manual Valve Closed
*c Adjustment Bolt
*d Clockwise


Using an 8 mm hexagon socket wrench, rotate the adjustment bolt clockwise to close the manual valve of the No. 3 hydrogen tank assembly.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:
·

The manual valve shuts off the pressure from the hydrogen tank assembly, so be careful not to damage the hexagonal portion.

·

If the hexagonal portion has been damaged, the No. 3 hydrogen tank assembly must be replaced.




d.

Before starting the depressurization procedure, first check that there is no mud or other contaminant around the medium pressure leak check port of the hydrogen supply regulator, and clean it as necessary.

HINT:

Installing the No. 1 hydrogen supply regulator plug while any foreign matter adheres to it can cause a hydrogen gas leak.



e.

Make sure that the manual valves of the No. 1 hydrogen tank assembly, No. 2 hydrogen tank assembly and No. 3 hydrogen tank assembly are closed.


f.
A479198

Slowly loosen the No. 1 hydrogen supply regulator plug until the hissing sound of gas escaping can be heard, then stop loosening the No. 1 hydrogen supply regulator plug and wait for the sound to stop. Repeat this procedure multiple times until the sound stops occurring, in order to depressurize the compressed hydrogen gas from the medium pressure leak check port of the hydrogen supply regulator.

CAUTION:
A477351C01
1.083,0.271 1.323,0.469 0.24,0.198 10 true *a
*a Manual Valve Open


·

Do not perform depressurization procedures when the manual valve of the hydrogen tank assembly is open.

·

The highly pressurized hydrogen gas inside the hydrogen tank assembly could blow out, resulting in a serious accident.


·
A477352

When performing depressurization, do not perform procedures by hand without wearing protective glasses and gloves.

·

High pressure nitrogen gas could cause a serious accident.



NOTICE:

When performing depressurization, only loosen the No. 1 hydrogen supply regulator plug. Do not remove it.



g.
A350032

Blow compressed air at the underside of the vehicle to disperse any accumulated hydrogen gas.


h.
A479199

Remove the No. 1 hydrogen supply regulator plug from the hydrogen supply regulator.

NOTICE:

When frost has formed on the hydrogen tank assembly or piping, water droplets may be formed when the frost begins to melt. If water droplets enter the tank or piping, it could result in blockage of the hydrogen piping, so do not allow water droplets to enter the tank or piping.



i.
A479200

Remove the O-ring from the hydrogen supply regulator.


j.
A479201C02
1.781,0.917 2.417,0.917 true 2.417,0.833 2.635,1.031 0.219,0.198 10 true *a
*a Protective Tape


To prevent damage to the seal portions and threaded portions, and to prevent foreign matter such as dust or metal fragments from entering the openings, cover the seal portions, threaded portions, and openings of the hydrogen supply regulator with protective tape.


k.
A479202

To prevent damage to the seal portions and threaded portions, and to prevent foreign matter such as dust or metal fragments from entering the openings, do not remove the protective tape covering the seal portions, threaded portions, and openings of the hydrogen supply regulator until immediately before performing work.

NOTICE:

When frost has formed on the hydrogen tank assembly or piping, water droplets may be formed when the frost begins to melt. If water droplets enter the tank or piping, it could result in blockage of the hydrogen piping, so do not allow water droplets to enter the tank or piping.



l.
A479203

Apply TOYOTA Genuine FC Grease to a new O-ring and to the threaded portion of the hydrogen supply regulator.


m.
A479204

Install the O-ring to the hydrogen supply regulator.

NOTICE:

During installation, make sure not to damage the O-ring.



n.
A479221C02
2.115,0.49 2.354,0.229 2.354,0.229 2.5,0.229 true 2.51,0.906 2.74,1.073 0.229,0.167 10 true *a 2.542,0.146 2.875,0.313 0.333,0.167 10 true SST
*a Specified tightening torque


Using SST install the No. 1 hydrogen supply regulator plug to the hydrogen supply regulator.

SST
09922-10240  

Torque:
Specified tightening torque:

9.0 N*m (92 kgf*cm, 80 in.*lbf)


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 40 mm (1.57 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 7.2 N*m (73 kgf*cm, 64 in.*lbf)




Hide 9. PRESSURE RELEASE OPERATION (for High Pressure)

a.

Prepare SST (hydrogen venting tool).

Click hereEngine / Hybrid System>FUEL>FUEL SYSTEM>DISCHARGE COMPRESSED HYDROGEN GAS


b.
A359849C01
0.76,4.208 1.177,3.792 false 0.583,4.146 0.896,4.344 0.313,0.198 10 false *a
*a SST (Venting Stand)


Check that the open/close valve of SST (venting stand) is closed.

SST
09404-62010  (09404-06010)


c.
A479195C02
1.479,2.948 1.323,2.948 1.323,2.948 1.052,2.844 true 2.688,3.052 2.688,2.792 true 1.5,2.875 1.813,3.031 0.313,0.156 10 false *c 0.906,1.969 1.219,2.125 0.313,0.156 10 false *a 2.594,1.969 2.906,2.125 0.313,0.156 10 false *b 2.635,3.073 2.948,3.229 0.313,0.156 10 false *c 1.24,3.135 1.583,3.365 0.344,0.229 10 false *d
*a Manual Valve Open
*b Manual Valve Closed
*c Adjustment Bolt
*d Clockwise


Using an 8 mm hexagon socket wrench, rotate the adjustment bolt clockwise to close the manual valve of the No. 1 hydrogen tank assembly.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:
·

The manual valve shuts off the pressure from the hydrogen tank assembly, so be careful not to damage the hexagonal portion.

·

If the hexagonal portion has been damaged, the No. 1 hydrogen tank assembly must be replaced.




d.
A479196C02
1.479,2.948 1.323,2.948 1.323,2.948 1.052,2.844 true 2.688,3.052 2.688,2.792 true 1.5,2.875 1.813,3.031 0.313,0.156 10 false *c 0.906,1.969 1.219,2.125 0.313,0.156 10 false *a 2.594,1.969 2.906,2.125 0.313,0.156 10 false *b 2.635,3.073 2.948,3.229 0.313,0.156 10 false *c 1.25,3.135 1.594,3.365 0.344,0.229 10 false *d
*a Manual Valve Open
*b Manual Valve Closed
*c Adjustment Bolt
*d Clockwise


Using an 8 mm hexagon socket wrench, rotate the adjustment bolt clockwise to close the manual valve of the No. 2 hydrogen tank assembly.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:
·

The manual valve shuts off the pressure from the hydrogen tank assembly, so be careful not to damage the hexagonal portion.

·

If the hexagonal portion has been damaged, the No. 2 hydrogen tank assembly must be replaced.




e.
A479197C02
1.479,2.948 1.323,2.948 1.323,2.948 1.052,2.844 true 2.688,3.052 2.688,2.792 true 1.5,2.875 1.813,3.031 0.313,0.156 10 false *c 0.906,1.969 1.219,2.125 0.313,0.156 10 false *a 2.594,1.969 2.906,2.125 0.313,0.156 10 false *b 2.635,3.073 2.948,3.229 0.313,0.156 10 false *c 1.24,3.135 1.583,3.365 0.344,0.229 10 false *d
*a Manual Valve Open
*b Manual Valve Closed
*c Adjustment Bolt
*d Clockwise


Using an 8 mm hexagon socket wrench, rotate the adjustment bolt clockwise to close the manual valve of the No. 3 hydrogen tank assembly.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:
·

The manual valve shuts off the pressure from the hydrogen tank assembly, so be careful not to damage the hexagonal portion.

·

If the hexagonal portion has been damaged, the No. 3 hydrogen tank assembly must be replaced.




f.

Before starting the depressurization procedure, first check that there is no mud or other contaminant around the medium pressure leak check port of the hydrogen supply regulator, and clean it as necessary.

HINT:

Installing the No. 1 hydrogen supply regulator plug while any foreign matter adheres to it can cause a hydrogen gas leak.



g.

Make sure that the manual valves of the No. 1 hydrogen tank assembly, No. 2 hydrogen tank assembly and No. 3 hydrogen tank assembly are closed.


h.
A479198

Slowly loosen the No. 1 hydrogen supply regulator plug until the hissing sound of gas escaping can be heard, then stop loosening the No. 1 hydrogen supply regulator plug and wait for the sound to stop. Repeat this procedure multiple times until the sound stops occurring, in order to depressurize the compressed hydrogen gas from the medium pressure leak check port of the hydrogen supply regulator.

CAUTION:
A477351C01
1.083,0.271 1.323,0.469 0.24,0.198 10 true *a
*a Manual Valve Open


·

Do not perform depressurization procedures when the manual valve of the hydrogen tank assembly is open.

·

The highly pressurized hydrogen gas inside the hydrogen tank assembly could blow out, resulting in a serious accident.


·
A477352

When performing depressurization, do not perform procedures by hand without wearing protective glasses and gloves.

·

High pressure nitrogen gas could cause a serious accident.



NOTICE:

When performing depressurization, only loosen the No. 1 hydrogen supply regulator plug. Do not remove it.



i.
A350032

Blow compressed air at the underside of the vehicle to disperse any accumulated hydrogen gas.


j.
A479199

Remove the No. 1 hydrogen supply regulator plug from the hydrogen supply regulator.

NOTICE:

When frost has formed on the hydrogen tank assembly or piping, water droplets may be formed when the frost begins to melt. If water droplets enter the tank or piping, it could result in blockage of the hydrogen piping, so do not allow water droplets to enter the tank or piping.



k.
A479200

Remove the O-ring from the hydrogen supply regulator.


l.
A479201C02
1.781,0.917 2.417,0.917 true 2.417,0.833 2.635,1.031 0.219,0.198 10 true *a
*a Protective Tape


To prevent damage to the seal portions and threaded portions, and to prevent foreign matter such as dust or metal fragments from entering the openings, cover the seal portions, threaded portions, and openings of the hydrogen supply regulator with protective tape.


m.
A479202

To prevent damage to the seal portions and threaded portions, and to prevent foreign matter such as dust or metal fragments from entering the openings, do not remove the protective tape covering the seal portions, threaded portions, and openings of the hydrogen supply regulator until immediately before performing work.

NOTICE:

When frost has formed on the hydrogen tank assembly or piping, water droplets may be formed when the frost begins to melt. If water droplets enter the tank or piping, it could result in blockage of the hydrogen piping, so do not allow water droplets to enter the tank or piping.



n.
A479203

Apply TOYOTA Genuine FC Grease to a new O-ring and to the threaded portion of the hydrogen supply regulator.


o.
A479204

Install the O-ring to the hydrogen supply regulator.

NOTICE:

During installation, make sure not to damage the O-ring.



p.

Connect SST (hydrogen venting tool).

SST
09404-62010  (09404-06010, 09404-06020, 09404-06030, 09404-06040, 09404-06050)

A479205C02
0.729,1.667 1.229,1.667 false 0.729,0.927 1.229,0.927 false 0.729,2.417 1.229,2.417 false 1.552,2.833 1.885,2.583 1.885,2.583 2.052,2.583 false 3.552,2.917 3.802,3.167 3.802,3.167 3.969,3.167 false 0.146,0.146 0.458,0.302 0.313,0.156 10 false *a 1.26,0.833 1.573,0.99 0.313,0.156 10 false *b 1.26,1.573 1.573,1.729 0.313,0.156 10 false *c 1.26,2.323 1.573,2.479 0.313,0.156 10 false *d 2.083,2.5 2.396,2.656 0.313,0.156 10 false *e 4,3.073 4.313,3.229 0.313,0.156 10 false *f
*a Concept of SST (hydrogen venting tool) Connection *b SST (Upper Release Pipe)
*c SST (Middle Release Pipe) *d SST (Lower Release Pipe)
*e SST (Venting Stand) *f SST (Flexible Hose)


HINT:

There are 2 types of SST (flexible hose).

A477394C02
4.531,0.125 4.844,0.281 0.313,0.156 10 false *b 1.979,0.104 2.292,0.26 0.313,0.156 10 false *a
*a Type A *b Type B




q.

for Type A:

i.
A479206C01
2.125,1.344 2.625,1.344 true 2.656,1.25 2.885,1.417 0.229,0.167 10 true *a
*a SST (Flexible Hose)


Temporarily install SST (flexible hose) to the hydrogen supply regulator.

SST
09404-62010  (09404-06020)


ii.
A479207C02
1.74,0.875 2.094,0.573 2.094,0.573 2.333,0.573 true 2.104,1.167 2.406,1.021 2.406,1.021 2.625,1.021 true 2.688,1.938 2.927,2.115 0.24,0.177 10 true *c 2.354,0.479 2.563,0.646 0.208,0.167 10 true *a 2.646,0.906 2.885,1.083 0.24,0.177 10 true *b
*a SST (Open End Wrench)
*b SST (Flexible Hose)
*c Specified tightening torque


Using SST(open end wrench), tighten SST (flexible hose).

SST
09404-62010  (09404-06020)
09922-10240  

Torque:
Specified tightening torque:

9.0 N*m (92 kgf*cm, 80 in.*lbf)


NOTICE:
·

Make sure that SST (flexible hose) does not interfere with part of the vehicle.

·

If SST (flexible hose) interferes with any part of the vehicle, protect it with a piece of cloth, etc.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 40 mm (1.57 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 7.2 N*m (73 kgf*cm, 64 in.*lbf)




iii.
A355008C01
2.375,1.365 2.375,1.021 false 1.313,1.5 1.021,1.5 false 2.313,1.354 2.625,1.51 0.313,0.156 10 false *a 1.354,1.438 1.667,1.594 0.313,0.156 10 false *b
*a SST (Flexible Hose)
*b SST (Venting Stand)


Connect SST (flexible hose) to SST (Venting Stand).

SST
09404-62010  (09404-06010, 09404-06020)



r.

for Type B:

i.
A479208

Remove the 3 bolts of the hydrogen supply regulator.


ii.
A479209C01
2.396,0.99 2.771,0.99 true 2.792,0.885 3.01,1.083 0.219,0.198 10 true *a
*a SST (Flexible Hose)


Temporarily install SST (flexible hose) to the hydrogen supply regulator.

SST
09404-62010  (09404-06020)


iii.
A479210

Install the hydrogen supply regulator with the 3 bolts.

Torque:
16.5 N*m (168 kgf*cm, 12 ft.*lbf)


iv.
A479211C02
1.708,0.354 2.177,0.156 2.177,0.156 2.385,0.156 true 1.917,0.5 2.406,0.5 true 2.375,1.083 2.688,1.24 0.313,0.156 10 true *c 2.417,0.063 2.677,0.229 0.26,0.167 10 true *a 2.417,0.406 2.677,0.573 0.26,0.167 10 true *b
*a SST (Open End Wrench)
*b SST (Flexible Hose)
*c Specified tightening torque


Using SST(open end wrench), tighten SST (flexible hose).

SST
09404-62010  (09404-06020)
09922-10240  

Torque:
Specified tightening torque:

9.0 N*m (92 kgf*cm, 80 in.*lbf)


NOTICE:
·

Make sure that SST (flexible hose) does not interfere with part of the vehicle.

·

If SST (flexible hose) interferes with any part of the vehicle, protect it with a piece of cloth, etc.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 40 mm (1.57 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 7.2 N*m (73 kgf*cm, 64 in.*lbf)




v.
A355008C01
2.375,1.365 2.375,1.021 false 1.313,1.5 1.021,1.5 false 2.313,1.354 2.625,1.51 0.313,0.156 10 false *a 1.354,1.438 1.667,1.594 0.313,0.156 10 false *b
*a SST (Flexible Hose)
*b SST (Venting Stand)


Connect SST (flexible hose) to SST (venting stand).

SST
09404-62010  (09404-06010, 09404-06020)



s.
A359851

Under basic conditions:

i.

Set SST (hydrogen venting tool) in an outdoor location.

NOTICE:

Take care that the compressed hydrogen gas that is discharged during the discharging procedure does not enter any indoor location.




t.
A361877

Other than basic conditions (when outdoor setup is not possible):

i.

When SST (hydrogen venting tool) will be set up indoors, locate it along a wall near a window, and with the tip of SST (upper release pipe) outdoors.

NOTICE:

Open windows on two sides or more, and ensure that there is adequate ventilation to prevent the compressed hydrogen gas that is discharged from collecting inside.




u.

Open the tank shut valves of the No. 1 hydrogen tank assembly, No. 2 hydrogen tank assembly No. 3 hydrogen tank assembly, and after 2 to 3 seconds, close the tank shut valves again.

CAUTION:
A359853

·

When opening the tank shut valve and applying pressure to SST (hydrogen venting tool), stay away from SST (flexible hose).

·

If SST (flexible hose) comes off, you could be struck by the loose end of SST (flexible hose), causing a serious accident.



NOTICE:

If the Data List item "Medium-range Hydrogen Pressure (gauge)" decreases to below 0.7 MPa (7.1 kgf/cm2, 102 psi) the tank shut valves of the No. 1 hydrogen tank assembly, No. 2 hydrogen tank assembly and No. 3 hydrogen tank assembly will forcibly close.



v.

If the tank shut valves of the No. 1 hydrogen tank assembly, No. 2 hydrogen tank assembly and No. 3 hydrogen tank assembly do not open, open the tank shut valves again, and after 2 to 3 seconds, close the tank shut valves.


w.

Perform preliminary leak check (using remaining piping pressure).

HINT:

Perform leak check using the pressure remaining upstream of the tank shut valve.


i.

If there are any water droplets, etc. adhering to the measurement locations, wipe them away before performing the procedure.

NOTICE:

Performing the measurement while any water droplets, etc. are adhering could damage the hydrogen gas detector.



ii.

Using SST and a hydrogen gas detector, inspect for leaks in the locations shown in the illustration.

SST
09401-62020  

Specified Value:

Less than 500 ppm


NOTICE:

If any values are outside the specified range, disconnect those locations that have leaks and assemble the parts again.


A479212C02
0.104,0.146 0.417,0.302 0.313,0.156 10 false *a
*a Locations to Check for Leaks - -
V100135

Leak Check Location - -




x.

Using the GTS, enter the following menus: Powertrain / FC / Data List / Medium-range Hydrogen Pressure

Powertrain > FC > Data List
Tester Display
Medium-Range Hydrogen Pressure
50003 490 60
HINT:

If the GTS setting is absolute pressure (abs), change it to gauge pressure (gauge).



y.

Open the tank shut valves of the No. 1 hydrogen tank assembly, No. 2 hydrogen tank assembly and No. 3 hydrogen tank assembly.

NOTICE:

If the Data List item "Medium-range Hydrogen Pressure (gauge)" decreases to below 0.7 MPa (7.1 kgf/cm2, 102 psi) the tank shut valves of the No. 1 hydrogen tank assembly, No. 2 hydrogen tank assembly and No. 3 hydrogen tank assembly will forcibly close.



z.

If the tank shut valves of the No. 1 hydrogen tank assembly, No. 2 hydrogen tank assembly and No. 3 hydrogen tank assembly do not open, open the tank shut valves again.


aa.
A359850C01
0.802,4.24 1.219,3.823 false 0.656,4.208 0.969,4.365 0.313,0.156 10 false *a
*a SST (Venting Stand)


Open the open/close valve of SST (venting stand), and depressurize compressed hydrogen gas.

SST
09404-62010  


ab.

Continue to monitor the Data List, and when the value of "Medium-range Hydrogen Pressure (gauge)" becomes 0.8 MPa (8.2 kgf/cm2, 116 psi), close the open/close valve of SST (venting stand).

NOTICE:
·

To protect the tank shut valve, make sure to first close the open/close valve of SST (venting stand).

·

Forgetting to close the open/close valve of SST (venting stand) and allowing the Data List item "Medium-range Hydrogen Pressure (gauge)" to decrease to below 0.7 MPa (7.1 kgf/cm2, 102 psi) will cause the tank shut valves of the No. 1 hydrogen tank assembly, No. 2 hydrogen tank assembly and No. 3 hydrogen tank assembly to forcibly close.




ac.

Check that the Data List item "Medium-range Hydrogen Pressure (gauge)" and the pressure on the pressure indicator of SST (venting stand) are less than 0.8 MPa (8.2 kgf/cm2, 116 psi).

NOTICE:
·

The pressure immediately after closing the open/close valve of SST (venting stand) should be less than 0.8 MPa (8.2 kgf/cm2, 116 psi) for both the Data List item "Medium-range Hydrogen Pressure (gauge)" and on the pressure indicator of SST (venting stand).

·

If either the Data List item "Medium-range Hydrogen Pressure (gauge)" or the pressure on the pressure indicator of SST (venting stand) are 0.8 MPa (8.2 kgf/cm2, 116 psi) or greater, open the open/close valve of SST (venting stand) and adjust the pressure.



HINT:

If the pressure immediately after closing the open/close valve of SST (venting stand) is less than 0.8 MPa (8.2 kgf/cm2, 116 psi) for both the Data List item "Medium-range Hydrogen Pressure (gauge)" and on the pressure indicator of SST (venting stand), then the pressurized hydrogen gas depressurizing procedure is complete.



ad.

Close the tank shut valves of both the No. 1 hydrogen tank assembly, No. 2 hydrogen tank assembly and No. 3 hydrogen tank assembly.


ae.
A359850C01
0.802,4.24 1.219,3.823 false 0.656,4.208 0.969,4.365 0.313,0.156 10 false *a
*a SST (Venting Stand)


Open the open/close valve of SST (venting stand) and discharge the compressed hydrogen gas remaining inside SST (flexible hose).

SST
09404-62010  (09404-06010)

NOTICE:
·

Do not disconnect SST (flexible hose) while there is still pressure remaining inside it.

·

Continue discharging until the pressure gauge of SST (Venting Stand) becomes "0".




af.

Before performing the disconnection procedure, if there are any contaminants such as water droplets adhering near the medium pressure leak check port of the hydrogen supply regulator, wipe them away before performing the procedure.


ag.
A355008C01
2.375,1.365 2.375,1.021 false 1.313,1.5 1.021,1.5 false 2.313,1.354 2.625,1.51 0.313,0.156 10 false *a 1.354,1.438 1.667,1.594 0.313,0.156 10 false *b
*a SST (Flexible Hose)
*b SST (Venting Stand)


Disconnect SST (flexible hose) from SST (Venting Stand).

SST
09404-62010  (09404-06010, 09404-06020)


ah.

for Type A:

i.
A479206C01
2.125,1.344 2.625,1.344 true 2.656,1.25 2.885,1.417 0.229,0.167 10 true *a
*a SST (Flexible Hose)


Remove SST (flexible hose) from the hydrogen supply regulator.

SST
09404-62010  (09404-06020)



ai.

for Type B:

i.
A479217C01
2.365,0.958 2.823,0.958 true 2.844,0.854 3.094,1.052 0.25,0.198 10 true *a
*a SST (Flexible Hose)


Loosen SST (flexible hose).

SST
09404-62010  (09404-06020)


ii.
A479218

Remove the 3 bolts of the hydrogen supply regulator.


iii.
A479219C01
2.365,0.979 2.885,0.979 true 2.896,0.885 3.115,1.063 0.219,0.177 10 true *a
*a SST (Flexible Hose)


Remove SST (flexible hose) from the hydrogen supply regulator.

SST
09404-62010  (09404-06020)


iv.
A479220

Install the hydrogen supply regulator with the 3 bolts.

Torque:
16.5 N*m (168 kgf*cm, 12 ft.*lbf)



aj.
A479200

Remove the O-ring from the hydrogen supply regulator.


ak.
A479201C02
1.781,0.917 2.417,0.917 true 2.417,0.833 2.635,1.031 0.219,0.198 10 true *a
*a Protective Tape


To prevent damage to the seal portions and threaded portions, and to prevent foreign matter such as dust or metal fragments from entering the openings, cover the seal portions, threaded portions, and openings of the hydrogen supply regulator with protective tape.


al.
A479202

To prevent damage to the seal portions and threaded portions, and to prevent foreign matter such as dust or metal fragments from entering the openings, do not remove the protective tape covering the seal portions, threaded portions, and openings of the hydrogen supply regulator until immediately before performing work.

NOTICE:

When frost has formed on the hydrogen tank assembly or piping, water droplets may be formed when the frost begins to melt. If water droplets enter the tank or piping, it could result in blockage of the hydrogen piping, so do not allow water droplets to enter the tank or piping.



am.
A479203

Apply TOYOTA Genuine FC Grease to a new O-ring and to the threaded portion of the hydrogen supply regulator.


an.
A479204

Install the O-ring to the hydrogen supply regulator.

NOTICE:

During installation, make sure not to damage the O-ring.



ao.
A479221C02
2.115,0.49 2.354,0.229 2.354,0.229 2.5,0.229 true 2.51,0.906 2.74,1.073 0.229,0.167 10 true *a 2.542,0.146 2.875,0.313 0.333,0.167 10 true SST
*a Specified tightening torque


Using SST install the No. 1 hydrogen supply regulator plug to the hydrogen supply regulator.

SST
09922-10240  

Torque:
Specified tightening torque:

9.0 N*m (92 kgf*cm, 80 in.*lbf)


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 40 mm (1.57 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 7.2 N*m (73 kgf*cm, 64 in.*lbf)