Home › Engine / Hybrid System › FUEL › HYDROGEN TANK ASSEMBLY (for No. 2)
RM37H0E _51 Engine / Hybrid System _097300 FUEL _0465033 HYDROGEN TANK ASSEMBLY(for No. 2) A

FUEL  HYDROGEN TANK ASSEMBLY(for No. 2)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A479270N03
2.49,1.146 3.073,1.146 false 5.604,5 5.792,4.51 5.792,4.51 5.979,4.51 false 1.25,4.333 1.583,4.333 false 3.177,3.615 3.677,3.615 false 4.25,5.083 4.083,5.083 4.083,5.083 3.75,4.677 false 1.531,2.385 1.365,2.385 1.365,2.385 1.198,2.896 false 5.333,3.719 5.917,3.719 false 3.667,2.417 4.083,2.417 false 4.958,0.542 5.208,0.542 5.208,0.542 5.625,1.125 false 4.427,0.938 4.594,0.938 4.594,0.938 4.844,1.521 false 5.833,2.594 6.333,2.594 false 6.656,5.292 6.49,5.292 6.49,5.292 6.323,4.906 false 6.615,0.583 6.781,0.583 false 6.594,0.229 6.76,0.229 false 3.188,1.583 3.438,1.75 0.25,0.167 10 false x 2 4.99,2.135 5.24,2.302 0.25,0.167 10 false x 2 4.854,2.323 5.104,2.49 0.25,0.167 10 false x 4 5.438,3.01 5.688,3.177 0.25,0.167 10 false x 2 6.042,1.875 6.292,2.042 0.25,0.167 10 false x 2 6.354,2.094 6.604,2.26 0.25,0.167 10 false x 6 6.594,1.646 6.844,1.813 0.25,0.167 10 false x 4 3.281,3.031 3.531,3.198 0.25,0.167 10 false x 3 4.802,4.292 5.052,4.458 0.25,0.167 10 false x 7 5.25,4.115 5.5,4.281 0.25,0.167 10 false x 2 0.823,3.458 1.073,3.625 0.25,0.167 10 false x 8 1.448,3.51 1.698,3.677 0.25,0.167 10 false x 3 2.802,5.167 3.052,5.333 0.25,0.167 10 false x 8 3.49,5.073 3.74,5.24 0.25,0.167 10 false x 3 2.375,4.365 2.625,4.531 0.25,0.167 10 false x 8 2.677,4.094 2.927,4.26 0.25,0.167 10 false x 2 0.51,5.01 0.76,5.177 0.25,0.167 10 false x 3 0.927,4.885 1.177,5.052 0.25,0.167 10 false x 6 1.115,4.719 1.365,4.885 0.25,0.167 10 false x 4 6.156,5.365 6.406,5.531 0.25,0.167 10 false x 2 6.021,4.427 6.281,4.573 0.26,0.146 10 false *1 5.583,0.073 6.646,0.354 1.063,0.281 18 false 1, 13, 14 1.635,4.177 1.865,4.448 0.229,0.271 18 false 2 3.719,3.479 3.948,3.75 0.229,0.271 18 false 3 4.615,4.948 4.844,5.219 0.229,0.271 18 false 4 1.906,2.25 2.135,2.521 0.229,0.271 18 false 5 5.969,3.563 6.198,3.833 0.229,0.271 18 false 6 4.135,2.271 4.365,2.542 0.229,0.271 18 false 7 4.76,0.396 5.094,0.667 0.333,0.271 18 false 8 6.385,2.438 6.719,2.708 0.333,0.271 18 false 10 2.313,1 2.552,1.26 0.24,0.26 18 false 9 4.125,0.781 4.458,1.052 0.333,0.271 18 false 11 6.698,5.135 7.031,5.406 0.333,0.271 18 false 12 6.302,0.438 6.646,0.708 0.344,0.271 18 false 15

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - - - (Click here)
2 REAR NO. 4 FLOOR BOARD SUB-ASSEMBLY 58404B - - -
3 REAR NO. 3 FLOOR BOARD SUB-ASSEMBLY 58403L - - -
4 NO. 2 FLOOR BOARD SUB-ASSEMBLY 58402K (Click here) - -
5 NO. 1 FLOOR BOARD SUB-ASSEMBLY 58401M (Click here) - -
6 REAR FLOOR SIDE MEMBER COVER LH 57628E - - -
7 REAR FLOOR SIDE MEMBER COVER RH 57627G - - -
8 NO. 1 FLOOR UNDER COVER 58398F - - -
9 NO. 1 DIFFERENTIAL SUPPORT PROTECTOR 52383E - - -
10 NO. 2 DIFFERENTIAL SUPPORT PROTECTOR 52384C - - -
11 REAR SUSPENSION BRACE COVER 53661B - - -
12 NO. 3 FC EXHAUST PIPE 17DB3 - - -
13 DISCHARGE COMPRESSED HYDROGEN GAS COMPRESSED HYDROGEN GAS - - - (Click here)
14 PRESSURE RELEASE OPERATION - - - (Click here)
15 CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - - - -

*1 HOSE CLAMP - -

A479191N06
2.604,2.146 2.948,2.438 2.948,2.438 3.177,2.438 false 2.885,2.104 3.396,2.104 false 3.427,2 3.719,2.188 0.292,0.188 10 false *1 3.396,2.344 3.688,2.51 0.292,0.167 10 false *2 3.219,2.333 3.375,2.531 0.156,0.198 10 false ●

*1 NO. 1 HYDROGEN SUPPLY REGULATOR PLUG *2 O-RING
● Non-reusable part
V100135

TOYOTA Genuine FC Grease

A487579N03
3.563,0.51 2.896,0.51 false 2.177,1.125 2.844,1.125 false 0.802,2.917 1.448,2.917 false 5.75,2.219 6.167,1.969 6.167,1.969 6.333,1.969 false 5.417,2.781 5.25,2.781 5.25,2.781 4.75,2.531 false 4.594,1.781 4.427,1.781 4.427,1.781 4.26,2.271 false 3.146,2.375 3.031,2.063 3.031,2.063 2.573,2.063 false 3.063,2.344 3.021,2.063 false 5.094,4.021 5.406,4.271 5.406,4.271 5.604,4.271 false 4.271,4.635 4.438,4.635 4.438,4.635 4.698,4.427 false 3.281,1.719 3.573,1.958 0.292,0.24 10 false x 2 1.719,4 2.042,4.208 0.323,0.208 10 false x 4 5.458,2.625 5.875,2.885 0.417,0.26 18 false 16 4.625,1.615 5.042,1.875 0.417,0.26 18 false 17 1.885,0.979 2.219,1.229 0.333,0.25 18 false 18 3.604,0.354 4.021,0.615 0.417,0.26 18 false 19 6.385,1.823 6.802,2.083 0.417,0.26 18 false 20 2.271,1.917 2.688,2.177 0.417,0.26 18 false 21 0.469,2.781 0.781,3.042 0.313,0.26 18 false 23 5.906,4.146 6.219,4.406 0.313,0.26 18 false 22 4.698,4.479 5.031,4.698 0.333,0.219 10 false x 2 3.906,4.552 4.313,4.729 0.406,0.177 10 false ● *1

Procedure Part Name Code
Z101186

Z101188

Z101187

16 HYDROGEN TANK TUBE JOINT ASSEMBLY (for Inlet Side) 77BC0 - - -
17 HYDROGEN TANK TUBE JOINT ASSEMBLY (for Outlet Side) 77BC0 - - -
18 MOTOR CABLE G1148 - - -
19 NO. 3 FLOOR WIRE 82163 - - -
20 NO. 3 FUEL TUBE CLAMP 77286H - - -
21 NO. 5 FUEL TUBE CLAMP 77286L - - -
22 NO. 3 HYDROGEN SUPPLY TUBE SUB-ASSEMBLY 77B0F (Click here) - -
23 NO. 2 HYDROGEN TANK ASSEMBLY 77A20 (Click here) - -

*1 O-RING - -
● Non-reusable part
V100135

TOYOTA Genuine FC Grease

A487581N02
3.51,2.281 3.344,2.281 3.344,2.281 2.917,1.823 false 0.667,2.406 1.25,2.406 false 5.188,0.5 5.854,0.5 false 5.219,1.396 5.552,0.979 5.552,0.979 5.719,0.979 false 6.656,2.646 6.49,2.646 6.49,2.646 6.365,2.302 false 1.135,3.802 1.302,3.802 1.302,3.802 1.385,3.99 false 2.281,4.885 2.448,4.885 2.448,4.885 2.698,4.729 false 3.583,4.885 4.25,4.885 false 2.531,4.01 2.698,4.26 2.698,4.26 2.865,4.26 false 1.021,4.969 1.438,4.969 false 2.365,5.667 2.781,5.667 false 3.271,5.469 4.188,5.469 false 5.583,2.719 5.417,2.719 5.417,2.719 5.167,2.385 false 5.375,3.26 5.958,3.26 false 5.313,4.177 5.979,4.177 false 2.458,0.698 2.792,0.698 false 3.656,1.375 3.99,1.375 false 2.448,0.917 2.781,1.083 2.781,1.083 2.948,1.083 false 3.646,1.604 3.979,1.771 3.979,1.771 4.146,1.771 false 1.833,0.958 1.427,0.604 1.427,0.604 1.177,0.604 false 0.573,4.5 1.021,4.5 false 5.885,0.354 6.292,0.615 0.406,0.26 18 false 24 5.635,2.573 6.042,2.833 0.406,0.26 18 false 25 6.313,3.146 6.719,3.406 0.406,0.26 18 false 26 6.323,4.042 6.729,4.302 0.406,0.26 18 false 27 4.24,5.313 4.646,5.573 0.406,0.26 18 false 28 6.688,2.479 7.094,2.74 0.406,0.26 18 false 29 5.771,0.833 6.177,1.094 0.406,0.26 18 false 30 2.833,0.563 3.24,0.823 0.406,0.26 18 false 31 0.365,2.25 0.771,2.51 0.406,0.26 18 false 33 3.552,2.135 3.958,2.396 0.406,0.26 18 false 32 1.969,4.74 2.375,5 0.406,0.26 18 false 35 4.302,4.75 4.708,5.01 0.406,0.26 18 false 34 2.99,1 3.25,1.156 0.26,0.156 10 false *1 4.188,1.688 4.427,1.844 0.24,0.156 10 false *1 2.896,4.177 3.135,4.323 0.24,0.146 10 false *2 0.802,4.885 1.01,5.052 0.208,0.167 10 false *3 2.156,5.583 2.396,5.729 0.24,0.146 10 false *3 4.583,0.438 4.906,0.656 0.323,0.219 10 false x 4 5.198,1.594 5.563,1.875 0.365,0.281 10 false x 2 6.302,1.573 6.615,1.813 0.313,0.24 10 false x 2 1.49,4.969 1.813,5.167 0.323,0.198 10 false x 4 2.875,5.604 3.177,5.802 0.302,0.198 10 false x 4 1.49,3.979 1.792,4.208 0.302,0.229 10 false x 2 2.802,4.688 3.115,4.948 0.313,0.26 10 false x 2 0.792,3.677 1.198,3.938 0.406,0.26 18 false 35 4.052,1.229 4.458,1.49 0.406,0.26 18 false 31 0.885,0.458 1.292,0.719 0.406,0.26 18 false 32 0.281,4.365 0.688,4.625 0.406,0.26 18 false 34

Procedure Part Name Code
Z101186

Z101188

Z101187

24 HYDROGEN DETECTOR G4151 - - -
25 NO. 8 HYDROGEN TANK TUBE 77BA8 - - -
26 NO. 6 HYDROGEN TANK TUBE 77BA6 (Click here) - -
27 NO. 3 HYDROGEN TANK TUBE 77BA3 (Click here) - -
28 NO. 4 FUEL TUBE CLAMP 77286J - - -
29 HYDROGEN SUPPLY REGULATOR ASSEMBLY 77AC0 - - -
30 NO. 1 HYDROGEN TANK BRACKET 77BB5 - - -
31 NO. 2 HYDROGEN TANK SPRING BOLT CUP 77B45B - - -
32 NO. 2 HYDROGEN TANK BAND SUB-ASSEMBLY 77B0A - - -
33 NO. 2 HYDROGEN TANK ASSEMBLY 77A20 (Click here) - -
34 NO. 2 HYDROGEN TANK FRAME SUB-ASSEMBLY - - - -
35 NO. 3 HYDROGEN TANK FRAME SEAT 77B61D (Click here) - -

*1 COMPRESSION SPRING *2 HARNESS BRACKET
*3 GROMMET - -

A482009N01
3.865,0.625 4.219,0.406 4.219,0.406 4.438,0.406 false 3.51,0.813 3.781,1.073 3.781,1.073 4,1.073 false 4.5,0.938 4.823,1.188 0.323,0.25 18 false 36 4.469,0.292 4.625,0.49 0.156,0.198 10 false ● 4.646,0.292 4.958,0.49 0.313,0.198 10 false *1 4.323,0.969 4.479,1.167 0.156,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

36 NO. 1 HYDROGEN TANK INFORMATION LABEL 77A18 (Click here) - -

*1 LABEL COVER FILM - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the No. 2 hydrogen tank assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effects/Inoperative when not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



CAUTION:
·
A477349

Work procedures must be performed in an area with good ventilation (airflow) where hydrogen gas will not accumulate, and flames or other things that could act as ignition sources must not be present.

·

Accumulated hydrogen gas could ignite, resulting in a serious accident.

·
A477350C01
1.083,1.229 1.406,0.833 1.406,0.833 1.573,0.833 false 1.604,0.75 1.854,0.927 0.25,0.177 10 true *a
*a When inside of piping is pressurized


Do not install or remove any hydrogen system components without first performing depressurization procedures.

·

The highly pressurized hydrogen gas inside the hydrogen tank assembly could blow out, resulting in a serious accident.

·
A477351C01
1.083,0.271 1.323,0.469 0.24,0.198 10 true *a
*a Manual Valve Open


Do not perform depressurization procedures when the manual valve of the hydrogen tank assembly is open.

·

The highly pressurized hydrogen gas inside the hydrogen tank assembly could blow out, resulting in a serious accident.

·
A477352

When performing depressurization, do not perform procedures by hand without wearing protective glasses and gloves.

·

The highly pressurized hydrogen gas inside the hydrogen tank assembly could blow out, resulting in a serious accident.

·
A477353C01
1.302,0.396 1.135,0.646 1.135,0.646 1.135,0.813 true 1.073,0.844 1.302,1 0.229,0.156 10 true *a
*a After depressurization procedures, the high pressure piping union nut that is loosened first.


After performing depressurization procedures, when first loosening the union nut of the high pressure hydrogen piping, do not loosen the union nut by hand without wearing protective glasses and gloves.

·

Even when depressurization procedures are performed, the pressurized hydrogen gas inside the high pressure hydrogen piping cannot be completely depressurized, so the highly pressurized hydrogen gas remaining in the high pressure hydrogen piping could blow out, resulting in a serious accident.

·
A340377C09
0.542,1.115 0.958,1.115 false 0.344,1.01 0.656,1.208 0.313,0.198 10 false *a
*a Heavy load exceeding the weight limits or size limits of the engine lifter


Because the hydrogen tank assembly is extremely heavy, make sure to follow the work procedures described in the repair manual.

·

If work is not performed according to the procedures described in the repair manual, there is a danger that the engine lifter could drop and components could fall down.

·
A421550

When hoisting up the hydrogen tank assembly, do not hoist it when not properly balanced.

·

The hydrogen tank assembly could fall, resulting in a serious accident.

·
A482144

When installing or removing a compressed hydrogen gas tank immediately after discharging compressed hydrogen gas, do not touch the tank or piping if there is frost on it.

·

Touching the tank or piping while there is frost on it could result in burn-like injuries due to frostbite.

·
A477354

When performing the primary leak inspection, do not perform procedures without wearing protective glasses and gloves.

·

High pressure nitrogen gas could cause a serious accident.

·
A359853

When opening the tank shut valve and applying pressure to SST (hydrogen venting tool), stay away from SST (flexible hose).

·

If SST (flexible hose) comes off, you could be struck by the loose end of SST (flexible hose), causing a serious accident.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

Place signs [HIGH PRESSURE GAS WORK IN PROGRESS - DO NOT TOUCH!], etc. to warn other technicians to be cautious. (An example sign is included, so make a copy and use it.)

A355341E01
0.552,8.167 6.667,8.51 6.115,0.344 10 false Place signs [HIGH PRESSURE GAS WORK IN PROGRESS - DO NOT TOUCH!], etc. to warn other technicians to be cautious. (An example sign is included, so make a copy and use it.)

·

When performing depressurization, do not open or close any parts of the hydrogen gas piping except for the following:

- Adjustment bolt of the hydrogen tank assembly manual valve

- Tank shut valve of the hydrogen tank assembly

- No. 1 hydrogen supply regulator plug

·

When installing or removing the hydrogen tank assembly, high pressure hydrogen piping, hydrogen inlet receptacle, hydrogen tank tube joint assembly or hydrogen supply regulator, to prevent strain such as twisting from being applied to the high pressure hydrogen piping.

·

Even when not removing or installing the high pressure hydrogen piping, be careful not to pull or otherwise apply strain to the high pressure hydrogen piping.

·

When reusable parts such as the hydrogen tank assembly valve portion, hydrogen inlet receptacle, hydrogen tank tube joint assembly and hydrogen supply regulator have been removed, to protect the seal portions and threaded portions from damage as well as to prevent foreign matter such as dust and metal fragments from entering through openings, cover these areas with protective tape.

·

Do not use packing tape, or any other tape that will leave residue on parts, as protective tape.

·
A339304C10
0.719,0.458 1.021,0.667 false 1.198,0.927 1.417,1.729 1.417,1.729 1.177,1.26 true 1.854,0.74 2,1.823 2,1.823 1.677,1.458 true 0.51,0.375 0.823,0.531 0.313,0.156 10 false *a 1.365,1.781 1.583,1.948 0.219,0.167 10 false *b 1.917,1.854 2.229,2.01 0.313,0.156 10 false *c
*a Protective Tape
*b Seal Portion
*c Threaded Portion


Protect seal portions and threaded portions as shown in the illustration.

·

To protect the seal portions and threaded portions from damage or contamination by foreign matter, remove the protective tape immediately before installation.

·

When reassembling components that have been removed, make sure that there is no foreign matter adhering to the openings.

·

After installing high pressure hydrogen system components, first perform primary leak inspection with low pressure nitrogen gas, and then perform secondary leak inspection.

·
A479186C01
2.396,0.635 2.979,0.635 true 1.698,1.667 2.281,1.667 true 3,0.552 3.313,0.75 0.313,0.198 10 false *a 2.313,1.594 2.625,1.792 0.313,0.198 10 false *b
*a Atmosphere Ventilation Hole Cap
*b Relief Valve


Do not insert any sharp objects into the relief valve of the hydrogen supply regulator.

·

Do not remove the atmosphere ventilation hole cap of the hydrogen supply regulator.

·

When the vehicle is parked with the ignition switch off, if the FC control ECU judges that the FC stack temperature will go below 0°C (32°F), it activates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds and drains water from the FC stack assembly. When performing inspection or repairs with the ignition switch off (not on (IG) or on (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work.

·

When frost has formed on the hydrogen tank assembly or piping, water droplets may be formed when the frost begins to melt. If water droplets enter the tank or piping, it could result in blockage of the hydrogen piping, so do not allow water droplets to enter the tank or piping.



Hide 58404B 2.REMOVE REAR NO. 4 FLOOR BOARD SUB-ASSEMBLY

a.
A477356C02
0,0 0,0 false
V100135

Bolt
V100136

Screw



Hide 58403L 3.REMOVE REAR NO. 3 FLOOR BOARD SUB-ASSEMBLY

a.
A477357C02
0,0 0,0 false
V100135

Screw
V100136

Nut
V100137

Grommet - -



Hide 58402K 4.REMOVE NO. 2 FLOOR BOARD SUB-ASSEMBLY

a.
A477358C02
3.094,0.229 3.25,0.469 0.156,0.24 18 false i 1.5,1.302 1.688,1.552 0.188,0.25 18 true ii
V100135

Bolt
V100136

Nut
V100137

Grommet - -


i.

Remove the 3 bolts and nut, detach the 8 clips and loosen the 5 grommets.


ii.

Slide the cover and loosen the grommet and remove the No. 2 floor board sub-assembly.



Hide 58401M 5.REMOVE NO. 1 FLOOR BOARD SUB-ASSEMBLY

a.
A477360C02
3.323,0.156 3.563,0.406 0.24,0.25 18 true i 1.5,0.323 1.74,0.573 0.24,0.25 18 true ii
V100135

Bolt
V100136

Nut
V100137

Grommet - -


i.

Remove the 3 bolts and nut, detach the 8 clips and loosen the 5 grommets.


ii.

Slide the cover and loosen the grommet and remove the No. 2 floor board sub-assembly.



Hide 57628E 6.REMOVE REAR FLOOR SIDE MEMBER COVER LH

a.
A477362


Hide 57627G 7.REMOVE REAR FLOOR SIDE MEMBER COVER RH

a.
A477363


Hide 58398F 8.REMOVE NO. 1 FLOOR UNDER COVER

a.
A477364C01
0,0 0,0 false
V100135

Screw
V100136

Nut
V100137

Grommet - -



Hide 52383E 9.REMOVE NO. 1 DIFFERENTIAL SUPPORT PROTECTOR

Hide 52384C 10.REMOVE NO. 2 DIFFERENTIAL SUPPORT PROTECTOR

Hide 53661B 11.REMOVE REAR SUSPENSION BRACE COVER

Hide 17DB3 12.REMOVE NO. 3 FC EXHAUST PIPE

Hide 13.DISCHARGE COMPRESSED HYDROGEN GAS COMPRESSED HYDROGEN GAS (When replacing the hydrogen tank assembly)

Hide 15.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 77BC0 16.REMOVE HYDROGEN TANK TUBE JOINT ASSEMBLY (for Inlet Side)

Hide 77BC0 17.REMOVE HYDROGEN TANK TUBE JOINT ASSEMBLY (for Outlet Side)

Hide G1148 18.REMOVE MOTOR CABLE

a.
A479149


Hide 82163 19.REMOVE NO. 3 FLOOR WIRE

a.
A479150


Hide 77286H 20.REMOVE NO. 3 FUEL TUBE CLAMP

a.
A479151


Hide 77286L 21.REMOVE NO. 5 FUEL TUBE CLAMP

a.
A479272N02
0.292,0.104 0.542,0.385 0.25,0.281 18 false i

i.

Detach the 3 clamp and disconnect the connector and 2 No. 5 fuel tube clamps from the No. 1 hydrogen tank bracket.



Hide 77B0F 22.DISCONNECT NO.3 HYDROGEN SUPPLY TUBE SUB-ASSEMBLY

a.
A477368N03
1.823,1.594 2.073,1.854 0.25,0.26 18 true ii 0.75,0.063 0.948,0.333 0.198,0.271 18 true i 3.969,0.167 4.219,0.427 0.25,0.26 18 true iii 3.969,1.49 4.24,1.76 0.271,0.271 18 true iv

i.

Remove the bolt and disconnect the No. 3 hydrogen supply tube sub-assembly from the hydrogen supply regulator.

NOTICE:

When frost has formed on the hydrogen tank assembly or piping, water droplets may be formed when the frost begins to melt. If water droplets enter the tank or piping, it could result in blockage of the hydrogen piping, so do not allow water droplets to enter the tank or piping.



ii.

Remove the 2 O-rings from the No. 3 hydrogen supply tube sub-assembly.


iii.

To prevent contamination by foreign matter, cover the connecting portions of the No. 3 hydrogen supply tube sub-assembly with plastic bags.


iv.

To prevent contamination by foreign matter, cover the openings of the hydrogen supply regulator with protective tape.

HINT:

When the hydrogen supply regulator will be replaced with a new one, it is not necessary to protect the openings with protective tape.




Hide 77A20 23.REMOVE NO. 2 HYDROGEN TANK ASSEMBLY

CAUTION:
A340377C01
0.542,1.115 0.958,1.115 false 0.344,1.01 0.656,1.208 0.313,0.198 10 false *a
*a Heavy load exceeding the weight limits or size limits of the engine lifter


·

Because the hydrogen tank assembly is extremely heavy, make sure to follow the work procedures described in the repair manual.

·

If work is not performed according to the procedures described in the repair manual, there is a danger that the engine lifter could drop and components could fall down.



a.
A479152


b.
A479134C02
1.25,0.417 1.667,0.198 1.667,0.198 1.885,0.198 true 0.333,1.365 0.49,1.365 0.49,1.365 0.771,0.823 true 4.083,0.625 4.313,0.438 4.313,0.438 4.458,0.438 true 6.479,0.583 6.708,0.396 6.708,0.396 6.854,0.396 true 1.927,0.115 2.24,0.271 0.313,0.156 10 false *a 0.167,1.281 0.479,1.438 0.313,0.156 10 false *b 4.49,0.365 4.802,0.521 0.313,0.156 10 false *c 4.365,0.75 4.677,0.906 0.313,0.156 10 true *d 6.885,0.323 7.115,0.479 0.229,0.156 10 false *e 0.365,0.052 0.583,0.302 0.219,0.25 18 true i 2.948,0.063 3.167,0.313 0.219,0.25 18 true ii 5.323,0.073 5.583,0.323 0.26,0.25 18 true iii 4.365,1.156 4.677,1.313 0.313,0.156 10 false *d 5.729,0.604 5.948,0.75 0.219,0.146 10 true *d 6,1.396 6.219,1.542 0.219,0.146 10 true *d
*a SST (Hydrogen Tank Stand No. 2) *b Belt
*c SST (Support No. 1) *d SST (Set Bolt A)
*e SST (Support No. 2) - -


i.

Set SST (hydrogen tank stand No. 2) on the engine lifter and secure it with the belt.

SST
09403-62030  

NOTICE:

Set SST (hydrogen tank stand No. 2) in the middle of the engine lifter and secure the center portion with the belt.



ii.

Remove 2 SST (set bolt A) and SST (support No. 1).

SST
09403-62030  (09403-06200, 09403-06210)


iii.

Remove 2 SST (set bolt A) and SST (support No. 2).

SST
09403-62030  (09403-06210, 09403-06220)



c.
A477430C03
6.198,0.594 6.031,0.594 true 2.917,2.302 3.229,2.156 3.229,2.156 3.354,2.156 true 2.771,2.385 3.354,2.385 true 2.844,2.792 3.208,2.646 3.208,2.646 3.333,2.646 true 2.75,3.115 3.208,2.927 3.208,2.927 3.333,2.927 true 0.51,0.698 0.823,0.854 0.313,0.156 10 false *a 2.063,0.427 2.375,0.583 0.313,0.156 10 true *f 3.969,0.417 4.26,0.635 0.292,0.219 10 true *g 5.823,1.708 6.135,1.865 0.313,0.156 10 true *h 0.406,3.333 0.719,3.49 0.313,0.156 10 true *i 6.531,0.573 6.729,0.76 0.198,0.188 10 true *j 5.865,0.5 6.031,0.667 0.167,0.167 10 true *c 2.073,3.646 2.385,3.802 0.313,0.156 10 true *f 3.99,3.646 4.292,3.833 0.302,0.188 10 true *g 0.396,1.708 0.708,1.865 0.313,0.156 10 true *h 5.813,3.323 6.125,3.479 0.313,0.156 10 true *i 0.406,0.115 0.656,0.406 0.25,0.292 18 false i 3.375,2.063 3.583,2.219 0.208,0.156 10 true *b 3.375,2.281 3.583,2.438 0.208,0.156 10 true *c 3.354,2.563 3.563,2.719 0.208,0.156 10 true *d 3.354,2.823 3.563,2.979 0.208,0.156 10 true *e
*a Front side of vehicle *b SST (Support Rail No. 1)
*c SST (Support No. 3) *d SST (Set Bolt C)
*e SST (Set Bolt B) *f Scale surface: 692 mm (27.2 in.)
*g Scale surface: 56 mm (2.20 in.) *h Scale surface: 88 mm (3.47 in.)
*i Scale surface: 467 mm (18.4 in.) *j Front side of vehicle: 244 mm (9.61 in.)
Rear side of vehicle: 265 mm (10.4 in.)


i.

Adjust SST (support No. 3), SST (support rail No. 1), and tighten SST (set bolt B), SST (set bolt C).

SST
09403-62030  (09403-06230, 09403-06250, 09403-06240, 09403-06260)

HINT:

This is done to align SST (hydrogen tank stand No. 2) with the installation condition of the No. 2 hydrogen tank assembly on the vehicle.




d.
A479153C02
2.125,0.375 2.375,0.375 true 5.354,1.667 5.604,1.667 true 2.146,0.677 2.396,0.677 true 5.375,1.979 5.625,1.979 true 2.281,1.885 2.531,1.885 true 0.406,0.104 0.594,0.365 0.188,0.26 18 false i 2.406,0.292 2.594,0.458 0.188,0.167 10 true *a 1.646,1.719 1.833,1.979 0.188,0.26 18 false ii 5.625,1.583 5.813,1.75 0.188,0.167 10 true *a 2.417,0.573 2.604,0.74 0.188,0.167 10 true *b 5.646,1.875 5.833,2.042 0.188,0.167 10 true *b 2.552,1.792 2.74,1.958 0.188,0.167 10 true *b
*a Protrusion *b SST (Support No. 3)


i.

Operate the engine lifter, and set SST (hydrogen tank stand No. 2) against the No. 2 hydrogen tank assembly.

NOTICE:

Align the protrusions of each No. 2 hydrogen tank frame sub-assembly with the holes of SST (support No. 3).



ii.

When the gap between the No. 2 hydrogen tank frame sub-assembly and SST (support No. 3) is large, rotate SST (support No. 3) to adjust the height.



e.
A479271N02
0.417,0.104 0.625,0.365 0.208,0.26 18 false i

i.

Remove the 5 bolts.


ii.

Operate the engine lifter and slowly remove the No. 2 hydrogen tank assembly from the vehicle.

NOTICE:
·

Make sure that the No. 2 hydrogen tank assembly does not interfere with the hydrogen tank tube.

·

Check the body paint near the mounting bolts of the No. 2 hydrogen tank frame sub-assembly, and if the paint is peeled off, apply paint.





Hide G4151 24.REMOVE HYDROGEN DETECTOR

a.
A487572


Hide 77BA8 25.REMOVE NO. 8 HYDROGEN TANK TUBE

Z101186

Click here(Click here)

Hide 77BA6 26.REMOVE NO. 6 HYDROGEN TANK TUBE

Z101186

CAUTION:
·

After performing depressurization procedures, when first loosening the union nut of the high pressure hydrogen piping, do not loosen the union nut by hand without wearing protective glasses and gloves.

·

Even when depressurization procedures are performed, the pressurized hydrogen gas inside the high pressure hydrogen piping cannot be completely depressurized, so the highly pressurized hydrogen gas remaining in the high pressure hydrogen piping could blow out, resulting in a serious accident.




a.
A487573N01
0.427,0.135 0.667,0.365 0.24,0.229 18 true i 4.396,0.125 4.635,0.354 0.24,0.229 18 true ii 4.385,1.604 4.656,1.854 0.271,0.25 18 true iii

i.

Detach the clamp and using a 19 mm union nut wrench, loosen the union nut and remove the No. 6 hydrogen tank tube from the No. 2 hydrogen tank assembly.

NOTICE:

When frost has formed on the hydrogen tank assembly or piping, water droplets may be formed when the frost begins to melt. If water droplets enter the tank or piping, it could result in blockage of the hydrogen piping, so do not allow water droplets to enter the tank or piping.



ii.

To prevent contamination by foreign matter, cover the openings of the No. 2 hydrogen tank assembly with protective tape.

HINT:

When the No. 2 hydrogen tank assembly will be replaced with a new one, it is not necessary to protect the openings with protective tape.



iii.

To prevent contamination by foreign matter, cover the connecting portions of the No. 6 hydrogen tank tube with plastic bags.



Hide 77BA3 27.REMOVE NO. 3 HYDROGEN TANK TUBE

Z101186

CAUTION:
·

After performing depressurization procedures, when first loosening the union nut of the high pressure hydrogen piping, do not loosen the union nut by hand without wearing protective glasses and gloves.

·

Even when depressurization procedures are performed, the pressurized hydrogen gas inside the high pressure hydrogen piping cannot be completely depressurized, so the highly pressurized hydrogen gas remaining in the high pressure hydrogen piping could blow out, resulting in a serious accident.




a.
A487575N01
0.583,0.125 0.802,0.406 0.219,0.281 18 true i 4.396,0.146 4.615,0.427 0.219,0.281 18 true ii 4.385,1.563 4.635,1.844 0.25,0.281 18 true iii

i.

Detach the clamp and using a 19 mm union nut wrench, loosen the union nut and remove the No. 3 hydrogen tank tube from the No. 2 hydrogen tank assembly.

NOTICE:

When frost has formed on the hydrogen tank assembly or piping, water droplets may be formed when the frost begins to melt. If water droplets enter the tank or piping, it could result in blockage of the hydrogen piping, so do not allow water droplets to enter the tank or piping.



ii.

To prevent contamination by foreign matter, cover the openings of the No. 2 hydrogen tank assembly with protective tape.

HINT:

When the No. 2 hydrogen tank assembly will be replaced with a new one, it is not necessary to protect the openings with protective tape.



iii.

To prevent contamination by foreign matter, cover the connecting portions of the No. 3 hydrogen tank tube with plastic bags.



Hide 77286J 28.REMOVE NO. 4 FUEL TUBE CLAMP

a.
A487577


Hide 77AC0 29.REMOVE HYDROGEN SUPPLY REGULATOR ASSEMBLY

Hide 77BB5 30.REMOVE NO. 1 HYDROGEN TANK BRACKET

a.
A479160


Hide 77B45B 31.REMOVE NO. 2 HYDROGEN TANK SPRING BOLT CUP

a.
A479161N02
0.417,0.094 0.583,0.354 0.167,0.26 18 false i

i.

Remove the 2 bolts, 2 No. 2 hydrogen tank spring bolt cups and 2 compression springs.



Hide 77B0A 32.REMOVE NO. 2 HYDROGEN TANK BAND SUB-ASSEMBLY

a.
A479162


Hide 77A20 33.REMOVE NO. 2 HYDROGEN TANK ASSEMBLY

a.
A479163C02
5.104,1.344 4.542,1.625 4.542,1.625 4.385,1.625 true 4.781,1.052 4.573,1.615 true 5.938,0.49 6.594,0.219 6.594,0.219 6.802,0.219 true 6.365,0.865 6.594,0.229 true 6.823,0.135 7.031,0.292 0.208,0.156 10 false *a 0.458,0.115 0.698,0.375 0.24,0.26 18 false i 4.292,0.115 4.531,0.375 0.24,0.26 18 false ii 4.167,1.542 4.375,1.698 0.208,0.156 10 false *a
*a Wheel Chocks - -


i.

Using an engine sling device and belts, remove the No. 2 hydrogen tank assembly from the No. 2 hydrogen tank frame sub-assembly.

CAUTION:
·
A421550

When hoisting up the hydrogen tank assembly, do not hoist it when not properly balanced.

·

The hydrogen tank assembly could fall, resulting in a serious accident.




ii.

Place the No. 2 hydrogen tank assembly on wheel chocks or similar.



Hide 34.REMOVE NO. 2 HYDROGEN TANK FRAME SUB-ASSEMBLY

a.
A479227N02
0.26,0.156 0.604,0.406 0.344,0.25 18 false i, ii 4.26,0.135 4.573,0.396 0.313,0.26 18 false iii

i.

Remove the nut and harness bracket.

HINT:

This procedure is only performed when the harness bracket is being replaced.



ii.

Remove the 8 grommets.

HINT:

This procedure is only performed when the grommet is being replaced.



iii.

Remove the No. 2 hydrogen tank frame sub-assembly LH and No. 2 hydrogen tank frame sub-assembly RH.



Hide 77B61D 35.REMOVE NO. 3 HYDROGEN TANK FRAME SEAT

Z101186

HINT:

This procedure is only performed when the No. 3 hydrogen tank frame seat is being replaced.



a.
A479164


Hide 77A18 36.REMOVE NO. 1 HYDROGEN TANK INFORMATION LABEL

Z101186

HINT:

This procedure is only performed when the No. 1 hydrogen tank information label is being replaced.



a.
A482136C01
4.01,0.927 4.25,0.302 4.25,0.302 4.448,0.302 false 4.031,1.021 4.26,1.448 4.26,1.448 4.458,1.448 true 4.479,0.229 4.792,0.385 0.313,0.156 10 false *1 4.479,1.375 4.792,1.531 0.313,0.156 10 false *2 0.406,0.094 0.781,0.354 0.375,0.26 18 false i, ii
*1 Label Cover Film *2 No. 1 Hydrogen Tank Information Label


i.

Using a scraper peel off the No. 1 hydrogen tank information label from the No. 2 hydrogen tank assembly.


ii.

Using a solvent and cloth, clean the contact surfaces of the No. 1 hydrogen information label and No. 2 hydrogen tank assembly.