| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | NO.2 HYDROGEN TANK BRACKET | 77BB6 | - | - | - |
| 2 | HYDROGEN SUPPLY REGULATOR ASSEMBLY | 77AC0 | - | - | - |
| 3 | NO. 8 HYDROGEN TANK TUBE | 77BA8 | ( )
|
- | - |
| 4 | NO.2 HYDROGEN TANK ASSEMBLY | 77A20 | - | - | - |
| *1 | NO. 1 HYDROGEN SUPPLY REGULATOR PLUG | *2 | O-RING |
| *3 | UPPER HYDROGEN SUPPLY REGULATOR CUSHION | *4 | HYDROGEN SUPPLY REGULATOR |
| *5 | LOWER HYDROGEN SUPPLY REGULATOR CUSHION | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| * | For use with SST or union nut wrench | ● | Non-reusable part |
|
TOYOTA Genuine FC Grease | - | - |
| *1 | HOSE CLAMP | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
77BB6
1.INSTALL NO.2 HYDROGEN TANK BRACKET
77AC0
2.INSTALL HYDROGEN SUPPLY REGULATOR ASSEMBLY
77BA8
3.INSTALL NO. 8 HYDROGEN TANK TUBE
|
|
| *a | Torque Wrench Fulcrum Length | - | - |
To prevent contamination by foreign matter, remove the plastic bags from the openings of the No. 8 hydrogen tank tube immediately before performing the procedure.
When frost has formed on the hydrogen tank assembly or piping, water droplets may be formed when the frost begins to melt. If water droplets enter the tank or piping, it could result in blockage of the hydrogen piping, so do not allow water droplets to enter the tank or piping.
To prevent contamination by foreign matter, remove the protective tape from the openings of the hydrogen supply regulator immediately before performing the procedure.
Attach the clamp and temporarily install the No. 8 hydrogen tank tube to the hydrogen supply regulator with the union nut.
Using a 19 mm union nut wrench, tighten the union nut while holding a tube part by hand.
25 N*m (255 kgf*cm, 18 ft.*lbf)
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When using a union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 21.4 N*m (218 kgf*cm, 16 ft.*lbf)
77A20
4.INSTALL NO.2 HYDROGEN TANK ASSEMBLY
5.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
6. FIRST LEAK CHECK
17DB3
7.INSTALL NO. 3 FC EXHAUST PIPE
8. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
9. SECOND LEAK CHECK
53661B
10.INSTALL REAR SUSPENSION BRACE COVER
52384C
11.INSTALL NO.2 DIFFERENTIAL SUPPORT PROTECTOR
52383E
12.INSTALL NO.1 DIFFERENTIAL SUPPORT PROTECTOR
58398F
13.INSTALL NO. 1 FLOOR UNDER COVER
57627G
14.INSTALL REAR FLOOR SIDE MEMBER COVER RH
57628E
15.INSTALL REAR FLOOR SIDE MEMBER COVER LH
58403L
18.INSTALL REAR NO. 3 FLOOR BOARD SUB-ASSEMBLY
58404B
19.INSTALL REAR NO. 4 FLOOR BOARD SUB-ASSEMBLY