|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf) : Specified torque |
| ● | Non-reusable part | - | - |
| *A | w/ Seat Heater System | *B | w/ Climate Control Seat System |
| *1 | REAR SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR) | *2 | REAR SEAT OUTER BELT ASSEMBLY RH (FLOOR ANCHOR) |
| *3 | REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH (FLOOR ANCHOR) | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
Move both front seats to the frontmost position and fold them forward.
73439
1.INSTALL REAR SEAT BELT RETRACTOR CUSHION LH
| *a | Mark-off Line | - | - |
Align with the mark-off line to install the rear seat belt retractor cushion LH as shown in the illustration.
73439
2.INSTALL REAR SEAT BELT RETRACTOR CUSHION RH
Use the same procedure described for the LH side.
73370E
3.INSTALL REAR SEAT OUTER BELT ASSEMBLY LH
| *a | Unlock | *b | Lock |
| *c | 45° | - | - |
|
Lock in this Direction |
|
Connector |
|
Bolt A |
|
Bolt B |
When the inclination of the retractor is 15° or less, check that the belt can be pulled from the retractor. When the inclination of the retractor is over 45°, check that the belt locks.
Do not disassemble the retractor.
Attach the guide.
Install the bolt A.
Install the bolt B.
Connect the pretensioner connector and lock it as shown in the illustration.
73360D
4.INSTALL REAR SEAT OUTER BELT ASSEMBLY RH
| *a | Unlock | *b | Lock |
| *c | 45° | - | - |
|
Lock in this Direction |
|
Connector |
|
Bolt A |
|
Bolt B |
When the inclination of the retractor is 15° or less, check that the belt can be pulled from the retractor. When the inclination of the retractor is over 45°, check that the belt locks.
Do not disassemble the retractor.
Connect the pretensioner connector and lock it as shown in the illustration.
Attach the guide.
Install the bolt A.
Install the bolt B.
62440
5.INSTALL ROOF SIDE RAIL GARNISH ASSEMBLY LH
62430
6.INSTALL ROOF SIDE RAIL GARNISH ASSEMBLY RH
62480A
7.INSTALL INNER ROOF SIDE GARNISH ASSEMBLY LH
62470A
8.INSTALL INNER ROOF SIDE GARNISH ASSEMBLY RH
62488A
9.INSTALL INNER ROOF SIDE GARNISH COVER LH
62487A
10.INSTALL INNER ROOF SIDE GARNISH COVER RH
62552F
11.INSTALL REAR SEAT SIDE GARNISH LH
62551F
12.INSTALL REAR SEAT SIDE GARNISH RH
62331A
14.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure described for the LH side.
67918F
15.INSTALL REAR DOOR SCUFF PLATE INSIDE LH
67917F
16.INSTALL REAR DOOR SCUFF PLATE INSIDE RH
71398A
17.INSTALL REAR SEATBACK HOLDER
72693
19.INSTALL REAR SEAT CUSHION LOCK HOOK
21.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
26. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART