Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › PEDESTRIAN PROTECTION SYSTEM
RM37H0E _58 Vehicle Interior _095287 SUPPLEMENTAL RESTRAINT SYSTEMS _0454682 PEDESTRIAN PROTECTION SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  PEDESTRIAN PROTECTION SYSTEM  B16A600  Chamber / Absorber Failure  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority Test Mode / Check Mode
B16A600 Chamber / Absorber Failure The pedestrian protection sensors and front bumper energy absorber detect a pressure higher than the specified value.
·

Front bumper energy absorber

·

Pedestrian detection chamber assembly (pedestrian protection sensor)

·

Airbag ECU assembly


Comes on SRS Airbag A Not applicable

WIRING DIAGRAM

C414484E06
5.385,3.958 6.854,4.198 1.469,0.24 10 false Airbag ECU Assembly 0.073,3.823 2.646,4.198 2.573,0.375 10 false Pedestrian Detection Chamber Assembly (Pedestrian Protection Sensor) 1.135,0.875 1.552,1.031 0.417,0.156 10 false PSR+ 1.146,3.354 1.594,3.531 0.448,0.177 10 false PSL- 1.135,2.521 1.531,2.708 0.396,0.188 10 false PSL+ 5.656,0.875 6.156,1.094 0.5,0.219 10 false PSR+ 1.146,1.698 1.552,1.875 0.406,0.177 10 false PSR- 5.646,1.698 6.135,1.885 0.49,0.188 10 false PSR- 5.656,2.521 6.042,2.677 0.385,0.156 10 false PSL+ 5.646,3.354 6.125,3.51 0.479,0.156 10 false PSL- 1.677,1.49 1.833,1.656 0.156,0.167 10 false 2 5.333,0.688 5.531,0.875 0.198,0.188 10 false 21 5.281,0.885 5.958,1.219 0.677,0.333 10 false G64 5.333,1.49 5.51,1.656 0.177,0.167 10 false 22 5.333,2.333 5.563,2.5 0.229,0.167 10 false 20 5.323,3.156 5.552,3.323 0.229,0.167 10 false 19 1.688,0.656 1.844,0.844 0.156,0.188 11 false 1 1.698,3.167 1.896,3.344 0.198,0.177 10 false 2 1.688,2.333 1.917,2.49 0.229,0.156 10 false 1 1.615,1.708 1.917,1.885 0.302,0.177 10 false A24 1.615,2.542 1.927,2.719 0.313,0.177 10 false A23 5.271,3.354 5.76,3.552 0.49,0.198 10 false G43 1.615,0.875 1.99,1.01 0.375,0.135 10 false A24 1.615,3.365 1.948,3.542 0.333,0.177 10 false A23 5.281,1.708 5.958,2.042 0.677,0.333 10 false G64 5.281,2.542 5.771,2.74 0.49,0.198 10 false G43

CAUTION / NOTICE / HINT

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

After replacing the airbag ECU assembly, refer to initialization.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



PROCEDURE

1.REPLACE FRONT BUMPER ENERGY ABSORBER
HINT:

If B16A600 is output, it is necessary to replace the front bumper energy absorber. Even if no cracks or other damage can be seen on the front bumper energy absorber, internal components may have been damaged, adversely affecting the operation of the pop up hood system.


a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.


c.

Replace the front bumper energy absorber with a new one.

HINT:

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER>REMOVAL



Result:
Proceed to
NEXT



NEXT

2.INSPECT PEDESTRIAN DETECTION CHAMBER ASSEMBLY (PEDESTRIAN PROTECTION SENSOR)
2.INSPECT PEDESTRIAN DETECTION CHAMBER ASSEMBLY (PEDESTRIAN PROTECTION SENSOR)

OK

3.CLEAR DTC

NG

5.REPLACE PEDESTRIAN DETECTION CHAMBER ASSEMBLY (PEDESTRIAN PROTECTION SENSOR)
3.CLEAR DTC
a.
C414483C01
0.552,1.667 0.865,1.865 0.313,0.198 10 false *1 2.521,1.635 2.833,1.833 0.313,0.198 10 false *2 1.615,1.083 1.927,1.281 0.313,0.198 10 false *3 1.594,0.208 1.906,0.406 0.313,0.198 10 false *3
*1 Pedestrian Detection Chamber Assembly (Pedestrian Protection Sensor)
*2 Airbag ECU Assembly
*3 Wire Harness


Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


c.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

4.CHECK DTC
4.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

a.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444

Result:
Result Proceed to
B16A600 is output A
B16A600 is not output B


Post-procedure1

a.

None



A

B

REPLACE PEDESTRIAN DETECTION CHAMBER ASSEMBLY (PEDESTRIAN PROTECTION SENSOR)

5.REPLACE PEDESTRIAN DETECTION CHAMBER ASSEMBLY (PEDESTRIAN PROTECTION SENSOR)
a.

Replace the pedestrian detection chamber assembly (pedestrian protection sensor) with a new one.

HINT:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>POP UP HOOD SENSOR>REMOVAL



Result:
Proceed to
NEXT



NEXT

6.CLEAR DTC
6.CLEAR DTC
a.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

Result:
Proceed to
NEXT



NEXT

END