Home › Engine / Hybrid System › FC CONTROL › HYDROGEN RECIRCULATION SEPARATOR
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466406 HYDROGEN RECIRCULATION SEPARATOR A

FC CONTROL  HYDROGEN RECIRCULATION SEPARATOR  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A480949N02
0.917,0.333 6.583,5.75 5.667,5.417 2,4.198 2.146,4.198 2.146,4.198 2.24,3.948 true 5,2.979 5,2.594 5,2.594 5.156,2.594 true 3.521,4.906 3.948,4.906 true 2.906,2.885 3.354,2.885 true 3.583,4.01 3.979,4.01 true 4.281,3.344 4.469,3.344 true 1.094,0.417 1.417,0.771 0.323,0.354 18 false 1 1.823,4.073 2.146,4.427 0.323,0.354 18 false 2 5.563,2.438 5.885,2.792 0.323,0.354 18 false 3 3.333,4.781 3.656,5.135 0.323,0.354 18 false 4 2.708,2.823 3.031,3.177 0.323,0.354 10 false *1 3.396,3.854 3.719,4.208 0.323,0.354 18 false 5 4.5,3.24 4.781,3.594 0.281,0.354 10 false ● 4.094,4.51 4.417,4.865 0.323,0.354 10 false x 3 4.5,5.063 4.781,5.344 0.281,0.281 10 false x 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 HYDROGEN RECIRCULATION PUMP ASSEMBLY WITH HYDROGEN RECIRCULATION SEPARATOR ASSEMBLY - - - -
2 WIRE HARNESS CLAMP BRACKET - - - -
3 HYDROGEN PUMP COOLING INLET HOSE 23C21 (Click here) - -
4 HYDROGEN RECIRCULATION SEPARATOR COVER 23C77 - - -
5 HYDROGEN RECIRCULATION SEPARATOR ASSEMBLY 23C70 (Click here) - -

*1 HYDROGEN RECIRCULATION PUMP ASSEMBLY - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the hydrogen recirculation separator assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link

*: The vehicle height changes because of suspension or tire replacement.

Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Wheel alignment adjustment Perform "Calibration" Electronically controlled brake system malfunctions (Click here)
Front bumper assembly (Including removal and installation)
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

TOYOTA Parking assist- sensor system

·

Parking support brake system

·

Advanced park


w/ Advanced Park:(Click here)
w/o Advanced Park:(Click here)
Front television camera view adjustment Panoramic view monitor system (Click here)
Suspension, tires, etc.*
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Parking support brake system

·

Advanced park


w/ Advanced Park:(Click here)
w/o Advanced Park:(Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle

·

Rear television camera view adjustment (for Rear camera detection system)


Panoramic view monitor system (Click here)
Perform headlight ECU sub-assembly LH initialization Automatic headlight beam level control system (Click here)

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -

·

The procedure listed below is for the LH side.

·

Use the same procedure for the RH and LH sides.



NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the front disc brake pads, the brake pedal may feel soft due to clearance between the front disc brake pads and front disc. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the front disc brake pads, always perform a road test to check the braking performance and check for vibrations.

·

When removing or installing the front disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



PROCEDURE

Hide 1.REMOVE HYDROGEN RECIRCULATION PUMP ASSEMBLY WITH HYDROGEN RECIRCULATION SEPARATOR ASSEMBLY

Hide 2.REMOVE WIRE HARNESS CLAMP BRACKET

Hide 23C21 3.REMOVE HYDROGEN PUMP COOLING INLET HOSE

Z101186

Click here(Click here)

Hide 23C77 4.REMOVE HYDROGEN RECIRCULATION SEPARATOR COVER

Hide 23C70 5.REMOVE HYDROGEN RECIRCULATION SEPARATOR ASSEMBLY

a.
A475883E01
0.396,0.156 0.677,0.51 0.281,0.354 18 false i 2.365,0.156 2.646,0.51 0.281,0.354 18 false ii 4.365,0.76 4.573,1.01 0.208,0.25 18 true iii 5.146,0.125 5.354,0.375 0.208,0.25 18 true iii

i.

Remove the 3 bolts and hydrogen recirculation separator assembly from hydrogen recirculation pump assembly.


ii.

Remove the O-ring from the hydrogen recirculation separator assembly.


iii.

Protect the openings of the hydrogen recirculation separator assembly and hydrogen recirculation pump assembly with protective tape (non-residue type) to prevent the entry of foreign matter or water.