Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT DOOR WINDOW FRAME MOULDING
RM37H0E _59 Vehicle Exterior _095315 EXTERIOR PANELS / TRIM _0448288 FRONT DOOR WINDOW FRAME MOULDING A

EXTERIOR PANELS / TRIM  FRONT DOOR WINDOW FRAME MOULDING  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B604620N03
4.219,1.708 4.302,1.542 4.302,1.542 4.552,1.542 false 4.75,0.583 4.833,0.417 4.833,0.417 5,0.417 false 1.938,3.583 2.188,3.583 2.188,3.583 2.271,3.417 false 0.313,2.969 0.583,2.354 0.583,2.354 0.833,2.354 false 6.271,0.677 6.521,0.677 6.521,0.677 6.604,0.844 false 3.354,0.531 3.688,0.531 false 4.802,1.406 5.083,1.76 0.281,0.354 18 false 1 0.948,2.219 1.229,2.573 0.281,0.354 18 false 2 1.729,3.448 2.01,3.802 0.281,0.354 18 false 3 3.146,0.427 3.427,0.781 0.281,0.354 18 false 4 5.365,0.292 5.646,0.646 0.281,0.354 18 false 5 6.688,0.813 7,1.01 0.313,0.198 10 false x 6 2.938,0.469 3.094,0.667 0.156,0.198 10 false ● 4.635,1.448 4.792,1.646 0.156,0.198 10 false ● 6.135,0.583 6.292,0.781 0.156,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 FRONT DOOR BELT MOULDING ASSEMBLY LH 75720 - - -
2 UPPER DOOR FRAME GARNISH LH 67664 - - -
3 FRONT DOOR WEATHERSTRIP LH 67862 - - -
4 FRONT DOOR WINDOW FRAME MOULDING LH 75756D (Click here) - -
5 FRONT DOOR UPPER WINDOW FRAME MOULDING LH 75754A (Click here) - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the front door window frame moulding and front door upper window frame moulding removal/installation are shown below.

Necessary Procedures after parts removed/installed/replaced
Replaced Part or Performed Procedures Necessary Procedures Effect/Inoperative Function when Necessary Procedures are not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
·

Front door glass (RH, LH) or front door glass run (RH, LH)

·

Because of assembly adjustment, etc., causing sliding change, improper reversal has occurred


Power window system initialization
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Key-linked function

·

Wireless transmitter-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system


-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -


·

Use the same procedure for the RH and LH sides.

·

The procedure described below is for the LH side.



PROCEDURE

Hide 75720 1.REMOVE FRONT DOOR BELT MOULDING ASSEMBLY LH

Hide 67664 2.REMOVE UPPER DOOR FRAME GARNISH LH

Hide 67862 3.DISCONNECT FRONT DOOR WEATHERSTRIP LH

a.
B599517


Hide 75756D 4.REMOVE FRONT DOOR WINDOW FRAME MOULDING LH

a.
B599518N01
4.833,0.438 5.115,0.792 0.281,0.354 18 false ii 2.344,1.021 2.625,1.375 0.281,0.354 18 false i 4.042,0 4.323,0.354 0.281,0.354 18 false iii 4.083,0.521 4.365,0.875 0.281,0.354 18 false iv 3.438,1.49 3.75,1.76 0.313,0.271 18 false v

i.

Put protective tape around the front door window frame moulding LH.


ii.

Heat the adhesive of the front door window frame moulding LH using a heat light.

Standard Value:
Part Temperature
Front Door Window Frame Moulding LH 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the front door window frame moulding LH excessively.



iii.

Using moulding remover D, detach the clip.


iv.

Using scraper, detach the double-sided tape.


v.

Detach the guide and remove the front door window frame moulding LH.



Hide 75754A 5.REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING LH

a.
B599519C02
0.729,1.073 0.469,0.729 false 5.375,0.344 5.75,0.198 false 0.323,1.135 0.479,1.333 0.156,0.198 10 false A 0.729,1.104 0.885,1.302 0.156,0.198 10 false *a 5.813,0.115 5.969,0.313 0.156,0.198 10 false *b 6.25,1.323 6.531,1.677 0.281,0.354 18 false i 0.438,0.125 1.031,0.458 0.594,0.333 18 false ii, iii 4.375,0.083 4.656,0.438 0.281,0.354 18 false iv 1.698,2.031 1.979,2.385 0.281,0.354 18 false v 6.875,0.688 7.156,1.042 0.281,0.354 18 false v
*a Tape *b Flange


i.

Put protective tape around the front door upper window frame moulding LH.


ii.

Insert a 4.0 mm (0.157 in.) drill bit into a drill.


iii.

Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

Standard Measurement:
Area Measurement Area Measurement
A 5.0 mm (0.197 in.) - -


NOTICE:

Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.



iv.

Lightly press the drill against the rivets to drill off the rivet flanges, and remove the 6 rivets.

CAUTION:

Be careful of the drilled rivets, as they may be hot.


NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Prying the rivets with the drill may damage the rivet installation holes or drill bit.




v.

Detach the claw and guide and remove the front door upper window frame moulding LH.