Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR DOOR WINDOW FRAME MOULDING
RM37H0E _59 Vehicle Exterior _095315 EXTERIOR PANELS / TRIM _0448289 REAR DOOR WINDOW FRAME MOULDING A

EXTERIOR PANELS / TRIM  REAR DOOR WINDOW FRAME MOULDING  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B604627N03
5.563,0.375 5.646,0.208 5.646,0.208 5.896,0.208 false 4.542,0.375 4.792,0.375 4.792,0.375 4.896,0.771 false 3.167,1.365 3.417,1.365 3.417,1.365 3.479,1.25 false 5.865,2.208 5.948,2.375 5.948,2.375 6.198,2.375 false 2.708,0.521 2.958,0.521 2.958,0.521 3.042,0.688 false 5.906,1.292 5.99,1.042 5.99,1.042 6.156,1.042 false 0.906,2.802 1.156,2.802 1.156,2.802 1.24,2.969 false 1.719,3.396 1.969,3.396 1.969,3.396 2.052,3.563 false 5.958,0.115 6.115,0.313 0.156,0.198 10 false ● 2.531,0.458 2.688,0.656 0.156,0.198 10 false ● 6.427,0.979 6.583,1.177 0.156,0.198 10 false ● 6.26,2.292 6.417,2.49 0.156,0.198 10 false ● 4.333,0.24 4.49,0.552 0.156,0.313 18 false 6 2.969,1.229 3.125,1.49 0.156,0.26 18 false 5 6.594,0.917 6.75,1.177 0.156,0.26 18 false 4 0.719,2.677 0.875,2.938 0.156,0.26 18 false 3 1.531,3.25 1.688,3.51 0.156,0.26 18 false 2 6.406,2.24 6.563,2.5 0.156,0.26 18 false 1 3.25,0.583 3.563,0.781 0.313,0.198 10 false x 3 5.646,0.417 5.958,0.615 0.313,0.198 10 false x 4

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REAR DOOR BELT MOULDING ASSEMBLY LH 75740 - - -
2 REAR DOOR FRAME GARNISH LH 67674B - - -
3 REAR DOOR WEATHERSTRIP LH 67872 - - -
4 REAR DOOR WINDOW FRAME MOULDING LH 75762B (Click here) - -
5 REAR DOOR REAR WINDOW FRAME MOULDING LH 75766A (Click here) - -
6 REAR DOOR UPPER WINDOW FRAME MOULDING LH 75764A (Click here) - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the rear door window frame moulding, rear door rear window frame moulding and rear door upper window frame moulding removal/installation are shown below.

Necessary Procedures after parts removed/installed/replaced
Replaced Part or Performed Procedures Necessary Procedures Effect/Inoperative Function when Necessary Procedures are not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
·

Rear door glass (RH, LH) or rear door glass run (RH, LH)

·

Because of assembly adjustment, etc., causing sliding change, improper reversal has occurred


Power window system initialization
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Key-linked function

·

Wireless transmitter-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system


-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -


·

Use the same procedure for both the RH and LH side.

·

The procedure described below is for the LH side.



PROCEDURE

Hide 75740 1.REMOVE REAR DOOR BELT MOULDING ASSEMBLY LH

Hide 67674B 2.REMOVE REAR DOOR FRAME GARNISH LH

Hide 67872 3.DISCONNECT REAR DOOR WEATHERSTRIP LH

a.
B599522


Hide 75762B 4.REMOVE REAR DOOR WINDOW FRAME MOULDING LH

a.
B599523N01
4.083,0.979 4.365,1.333 0.281,0.354 18 false i 0.771,0.229 1.052,0.583 0.281,0.354 18 false ii 4.021,0 4.302,0.333 0.281,0.333 18 false iii 3.01,0.208 3.292,0.542 0.281,0.333 18 false iv 3.115,1.292 3.396,1.625 0.281,0.333 18 false v

i.

Put protective tape around the rear door window frame moulding LH.


ii.

Heat the adhesive of the rear door window frame moulding LH using a heat light.

Standard Value:
Part Temperature
Rear Door Window Frame Moulding LH 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rear door window frame moulding LH excessively.



iii.

Using moulding remover D, detach the clip.


iv.

Using scraper, detach the double-sided tape.


v.

Detach the guide and remove the rear door window frame moulding LH.



Hide 75766A 5.REMOVE REAR DOOR REAR WINDOW FRAME MOULDING LH

a.
B599524C03
0.885,1.01 0.531,0.656 false 6.531,1.125 6.25,1.198 false 3.26,0.958 3.542,1.313 0.281,0.354 18 false i 0.49,0.073 1.01,0.438 0.521,0.365 18 false ii, iii 5.167,1.031 5.448,1.385 0.281,0.354 18 false iv 0.385,1.063 0.542,1.26 0.156,0.198 10 false A 0.844,1.031 1,1.229 0.156,0.198 10 false *a 6.563,1.052 6.719,1.25 0.156,0.198 10 false *b 3.885,0.115 4.167,0.469 0.281,0.354 18 false v
*a Tape *b Flange


i.

Put protective tape around the rear door rear window frame moulding LH.


ii.

Insert a 4.0 mm (0.157 in.) drill bit into a drill.


iii.

Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

Standard Measurement:
Area Measurement Area Measurement
A 5.0 mm (0.197 in.) - -


NOTICE:

Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.



iv.

Lightly press the drill against the rivets to drill off the rivet flanges, and remove the 3 rivets.

CAUTION:

Be careful of the drilled rivets, as they may be hot.


NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Prying the rivets with the drill may damage the rivet installation holes or drill bit.




v.

Detach the guide and remove the rear door rear window frame moulding LH.



Hide 75764A 6.REMOVE REAR DOOR UPPER WINDOW FRAME MOULDING LH

a.
B599525C02
0.49,0.698 0.813,0.969 false 6.521,0.552 6.708,0.438 false 0.323,1.104 0.479,1.302 0.156,0.198 10 false A 0.833,0.979 0.99,1.177 0.156,0.198 10 false *a 6.74,0.292 6.896,0.49 0.156,0.198 10 false *b 3.646,1.438 3.927,1.792 0.281,0.354 18 false i 0.438,0.094 0.99,0.438 0.552,0.344 18 false ii, iii 6,0.104 6.281,0.458 0.281,0.354 18 false iv 2.802,0.813 3.083,1.167 0.281,0.354 18 false v
*a Tape *b Flange


i.

Put protective tape around the rear door upper window frame moulding LH.


ii.

Insert a 4.0 mm (0.157 in.) drill bit into a drill.


iii.

Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

Standard Measurement:
Area Measurement Area Measurement
A 5.0 mm (0.197 in.) - -


NOTICE:

Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.



iv.

Lightly press the drill against the rivets to drill off the rivet flanges, and remove the 4 rivets.

CAUTION:

Be careful of the drilled rivets, as they may be hot.


NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Prying the rivets with the drill may damage the rivet installation holes or drill bit.




v.

Detach the guide and remove the rear door upper window frame moulding LH.