Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM37H0E _58 Vehicle Interior _095300 HEATING / AIR CONDITIONING _0455055 AIR CONDITIONING SYSTEM J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  Ambient Temperature Display System  


DESCRIPTION

The thermistor assembly (ambient temperature sensor) is installed in front of the cooler condenser assembly to detect the ambient temperature which is used to control the air conditioning system AUTO mode. This sensor is connected to the air conditioning amplifier assembly and detects fluctuations in the ambient temperature. This data is used for controlling the cabin temperature. The sensor sends a signal to the air conditioning amplifier assembly. The resistance of the thermistor assembly (ambient temperature sensor) changes in accordance with the ambient temperature. As the temperature decreases, the resistance increases. Conversely, as the temperature increases, the resistance decreases.

The air conditioning amplifier assembly applies a voltage (5 V) to the thermistor assembly (ambient temperature sensor) and reads voltage changes due to changes in the resistance of the thermistor assembly (ambient temperature sensor).

NOTICE:

The thermistor assembly (ambient temperature sensor) is installed on the front of the cooler condenser assembly in the engine room and detects the ambient temperature around the installation area (the ambient temperature detected is the temperature detected around the thermistor assembly (ambient temperature sensor) and not the ambient temperature of the air surrounding the vehicle). Therefore, the ambient temperature around the thermistor assembly (ambient temperature sensor) changes depending on the radiated heat from the engine room and the ambient temperature display value is affected by vehicle speed. In the following cases, the ambient temperature of the air surrounding the vehicle and the displayed value are different and the speed at which the displayed value updates is delayed. However, this is not a malfunction.

·

When the vehicle is stopped or being driven at a low speed, the value is not updated to a higher temperature in order to minimize the effects of the radiated heat from the engine on the heater and air conditioner "AUTO" control. Since the same adjustment also occurs while the vehicle is being driven at medium to high speeds, updating to a higher temperature is delayed. However, the value is updated to a lower temperature regardless of the vehicle speed.

·

The ambient temperature around the thermistor assembly (ambient temperature sensor) installation area drastically changes due to a cause other than the radiated heat from the engine (vehicle garage, entering or exiting a tunnel, etc.).



WIRING DIAGRAM

E407114E10
4.542,1.604 5,1.802 0.458,0.198 10 false D80 4.542,1.781 6.896,2.104 2.354,0.323 10 false Air Conditioning Amplifier Assembly 4.781,0.531 5.24,0.729 0.458,0.198 10 false TAM 4.792,1 5.25,1.198 0.458,0.198 10 false SG-2 4.5,1.01 4.917,1.177 0.417,0.167 10 false 14 4.573,0.531 4.99,0.698 0.417,0.167 10 false 1 2.99,0.531 3.406,0.698 0.417,0.167 10 false 2 2.688,1.01 3.104,1.177 0.417,0.167 10 false - 1.365,1.51 1.823,1.708 0.458,0.198 10 false A35 1.354,1.677 3.708,2 2.354,0.323 10 false Thermistor Assembly 5.708,0.198 6.167,0.396 0.458,0.198 10 false 5 V 6.177,0.646 6.635,0.844 0.458,0.198 10 false AD 2.708,0.531 3.125,0.698 0.417,0.167 10 false +

CAUTION / NOTICE / HINT

NOTICE:
·

When installing the spiral cable sub-assembly and steering wheel, be sure to adjust the spiral cable sub-assembly as it may break if the steering wheel is turned before adjusting the spiral cable sub-assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>INITIALIZATION

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Before starting the inspection, it is necessary to release the residual heat from the engine room (engine unit and coolant hoses, etc.) after stopping the engine and electric motor (when the vehicle is parked after being driven). Therefore, move and park the vehicle in the following type of temperature measurement location.

-

A location within the vehicle service area which has a relatively low amount of environmental temperature changes in the area surrounding the vehicle.

-

A location with a level surface made of a material such as concrete which transmits a relatively low amount of heat from the ground, such as concrete.

-

A location with no heat influences around the vehicle to be inspected such as other vehicles with a running engine and electric motors, exhaust gas ducts installed on the exhaust pipes, stoves, etc.


·

When the servo motor or air conditioning amplifier assembly is replaced, be sure to perform servo motor initialization.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>INITIALIZATION

·

The air conditioning system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the air conditioning system after confirming that the communication system is functioning properly.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

ignition switch operation during parked vehicle inspection:

Turn the ignition switch to ON. (Do not start the engine and electric motor.)



PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Body Electrical > Air Conditioner > Clear DTCs
50002 121

b.

Check for DTCs when the following conditions are met.

Body Electrical > Air Conditioner > Trouble Codes
50001 121
NOTICE:

During the parked vehicle inspection, perform the inspection with the ignition switch to ON (do not start the engine and electric motor).



Result:
Result Proceed to
DTC B1412 is not output A
DTC B1412 is output B



A

2.INSPECT THERMISTOR ASSEMBLY (AMBIENT TEMPERATURE SENSOR)

B

2.INSPECT THERMISTOR ASSEMBLY (AMBIENT TEMPERATURE SENSOR)

OK

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - THERMISTOR ASSEMBLY)

NG

REPLACE THERMISTOR ASSEMBLY (AMBIENT TEMPERATURE SENSOR)

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - THERMISTOR ASSEMBLY)
NOTICE:

During the parked vehicle inspection, perform the inspection with the ignition switch off (do not start the engine and electric motor).


a.

Disconnect the D80 air conditioning amplifier assembly connector.


b.

Disconnect the A35 thermistor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D80,A35)Location & Routing

Click Connector(D80)Instrument Panel>Instrument Panel Wire>Air Conditioning Amplifier Assembly

Click Connector(A35)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Thermistor Assembly

D80-1 (TAM) - A35-2 (+) Always Below 1 Ω
D80-14 (SG-2) - A35-1 (-) Always Below 1 Ω
D80-1 (TAM) or A35-2 (+)- Other terminals and body ground Always 10 kΩ or higher
D80-14 (SG-2) or A35-1 (-) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK AMBIENT TEMPERATURE COMPARISON

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK AMBIENT TEMPERATURE COMPARISON
a.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.

NOTICE:

Make sure the wire harness(es) and connector(s) for the vehicle being inspected are connected. After the ignition switch is turned off, the navigation system stores the various memory and settings within approximately 6 minutes. Therefore, make sure to disconnect the cable from the negative (-) auxiliary battery terminal after confirming that 6 minutes or more have elapsed since turning the ignition switch off.



b.

Disconnect the cable from the negative (-) auxiliary battery terminal and wait 90 seconds or more.

HINT:

The air conditioning amplifier assembly reads and memorizes the thermistor assembly (ambient temperature sensor) detection value (THO) from before the ignition switch was turned off for 1 hour after turning the ignition switch off. Therefore, it is necessary to switch off the air conditioning amplifier assembly internal power source and clear the stored values from before the ignition switch was turned off.



c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Using a thermometer, measure the ambient temperature of the installation area around the thermistor assembly (ambient temperature sensor) and record it.

NOTICE:
·

During the parked vehicle inspection, perform the inspection with the ignition switch to ON (do not start the engine and electric motor).

·

Set the thermometer so that the measuring tip is at approximately the same height and lateral position as the thermistor assembly (ambient temperature sensor) installed behind the front grille and approximately 5 cm from the surface of the front grille, and then maintain the thermometer in that position.

·

After the ignition switch is turned to ON, the ambient temperature, detected signal value and sensing portion temperature of the thermistor assembly (ambient temperature sensor) and the measuring tip of the thermometer will equalize. Therefore, make sure to wait approximately 6 minutes before measuring.

·

If the temperature sensing portion of the thermistor assembly (ambient temperature sensor) is touched, the body temperature of the technician may cause an incorrect temperature measurement. Therefore, do not touch the temperature sensor when measuring the ambient temperature of the installation area around the thermistor assembly (ambient temperature sensor).

·

Do not move the thermometer from the maintained position, touch the measuring tip or allow it to contact the front grille.




e.

Record the ambient temperature value displayed on the multi-information display of the combination meter assembly.


f.

Compare the ambient temperature of the installation area around the thermistor assembly (ambient temperature sensor) with the ambient temperature value displayed on the multi-information display of the combination meter assembly.

Standard:

The ambient temperature of the installation area around the thermistor assembly (ambient temperature sensor) is approximately the same as the ambient temperature value displayed on the multi-information display of the combination meter assembly.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY