Home › Engine / Hybrid System › FC CONTROL › FC CONTROL SYSTEM › 2020.11–2021.08
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466766 FC CONTROL SYSTEM C

FC CONTROL  FC CONTROL SYSTEM  P1DA01C  Hydrogen Injector 2 Circuit Voltage Out of Range  


DESCRIPTION

Refer to DTC P1D9A1C.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>P1D9A1C

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1DA01C Hydrogen Injector 2 Circuit Voltage Out of Range All of the following conditions are met, and there is an open in the No. 2 fuel injector assembly circuit or a short to the GND circuit (DTC detection signal is ON) for more than 3 seconds.
·

Auxiliary battery voltage is between 10.5 to 15 V

·

No. 2 fuel injector assembly is not in operation


(1 trip detection logic)
All of the following conditions are met, and there is a short in the +B circuit of the No. 2 fuel injector assembly circuit (DTC detection signal is ON) for more than 3 seconds.
·

Auxiliary battery voltage is between 10.5 to 15 V

·

No. 2 fuel injector assembly is not in operation


(1 trip detection logic)
·

No. 2 fuel injector assembly

·

FC control ECU

·

FC-B relay

·

Wire harness or connector


Master Warning: Comes on FC A

Detection timing
Vehicle Condition FC shutdown
(ignition switch ON)
FC startup process FC intermittent operation FC is generating power
(vehicle is in stationary)
FC is generating power
(vehicle is traveling)
FC shutdown process
Data List (EV)
"FC Work Mode"
Stop Startup Working Finishing
Data List (EV)
"FC Intermittent Operation"
OFF ON OFF OFF
DTC Detection ○ ○ ○ ○ ○ -

Related Data List
DTC No. Data List
P1DA01C -

HINT:

It is suspected that malfunctions, or open/short circuits have occurred in the No. 2 fuel injector assembly.


WIRING DIAGRAM

A477002E06
0.531,0.51 1.448,0.708 0.917,0.198 10 false FC-B NO. 1 3.521,0.385 4.438,0.583 0.917,0.198 10 false +BP3 1.625,2.438 2.542,2.635 0.917,0.198 10 false IGCT NO. 2 0.583,3.823 1.177,4.292 0.594,0.469 10 false Auxiliary Battery 1.542,1.688 1.708,1.854 0.167,0.167 10 false 3 1.542,2.042 1.708,2.208 0.167,0.167 10 false 2 2.313,2.052 2.479,2.219 0.167,0.167 10 false 1 2.313,1.677 2.479,1.844 0.167,0.167 10 false 5 1.49,0.625 1.656,0.792 0.167,0.167 10 false 2 2.281,0.646 2.448,0.813 0.167,0.167 10 false 1 2.292,0.26 2.458,0.427 0.167,0.167 10 false 5 1.49,0.26 1.656,0.427 0.167,0.167 10 false 3 3.521,3.667 4.438,3.865 0.917,0.198 10 false E1 3.198,3.656 3.594,4.042 0.396,0.385 10 false B1 3.177,0.375 3.542,0.646 0.365,0.271 10 false A48 5.198,1.24 5.563,1.49 0.365,0.25 10 false B1 5.208,1.771 5.542,2.042 0.333,0.271 10 false B1 4.781,1.135 5.698,1.333 0.917,0.198 10 false VHI2 4.792,1.656 5.708,1.854 0.917,0.198 10 false HIN2 5.906,1.125 6.823,1.323 0.917,0.198 10 false VHI2 5.917,1.656 6.833,1.854 0.917,0.198 10 false HIN2 5.719,1.125 5.885,1.292 0.167,0.167 10 false 1 5.708,1.667 5.875,1.833 0.167,0.167 10 false 2 5.813,2.563 6.958,2.979 1.146,0.417 10 false No. 2 Hydrogen Injector Assembly 5.802,2.385 6.219,2.646 0.417,0.26 10 false B8 5.208,1.583 5.438,1.75 0.229,0.167 10 false 84 5.208,1.042 5.438,1.208 0.229,0.167 10 false 44 3.24,0.198 3.469,0.365 0.229,0.167 10 false 2 3.156,3.469 3.438,3.635 0.281,0.167 10 false 104 1.74,1 2.656,1.198 0.917,0.198 10 false FC-B 3.823,4.031 5.229,4.333 1.406,0.302 10 false FC Control ECU 3.604,2.573 4.344,3.198 0.74,0.625 10 false DTC detection signal 4.094,0.677 4.552,0.875 0.458,0.198 10 false +BP3 4.74,0.677 5.198,0.875 0.458,0.198 10 false +BP3 1.646,3.948 2.76,4.302 1.115,0.354 10 false EV Control ECU 0.417,0.896 1.333,1.094 0.917,0.198 10 false R/B-B NO. 1 0.406,1.448 1.323,1.646 0.917,0.198 10 false R/B FR 0.604,1.948 1.521,2.146 0.917,0.198 10 false IGCT NO. 2 0.573,3 1.281,3.26 0.708,0.26 10 false R/R RR# 2 1.646,3.333 2.24,3.563 0.594,0.229 10 false MREL 1.656,3.792 2.146,3.969 0.49,0.177 10 false A8*1 1.396,3.219 1.594,3.375 0.198,0.156 10 false 21 2.594,1.333 3.375,1.771 0.781,0.438 10 false IGCT NO. 6 2.427,0.521 3.344,0.719 0.917,0.198 10 false FC-B NO. 4 1.99,3.792 2.479,3.969 0.49,0.177 10 false D15*2 5.719,3.896 6.625,4.094 0.906,0.198 10 false *1: for LHD 5.729,4.24 6.635,4.438 0.906,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the ignition switch to ON and wait for 3 seconds or more.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FC CONTROL ECU)

Pre-procedure1

a.

Disconnect the FC control ECU connector.


b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A48,B1)Location & Routing

Click Connector(A48)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>FC Control ECU

Click Connector(B1)Engine Compartment>No. 2 Stack Wire>FC Control ECU

A48-2 (+BP3) - B1-104 (E1) Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the FC control ECU connector.



OK

2.CHECK HARNESS AND CONNECTOR (FC CONTROL ECU - NO. 2 FUEL INJECTOR ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (FC CONTROL ECU - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (FC CONTROL ECU - NO. 2 FUEL INJECTOR ASSEMBLY)

Pre-procedure1

a.

Disconnect the FC control ECU connector.


b.
A476954

Disconnect the No. 2 fuel injector assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B1,B8)Location & Routing

Click Connector(B1)Engine Compartment>No. 2 Stack Wire>FC Control ECU

Click Connector(B8)Engine Compartment>No. 2 Stack Wire>No. 2 Fuel Injector Assembly

B1-44 (VHI2) - B8-1 (VHI2) Always Below 1 Ω
B1-84 (HIN2) - B8-2 (HIN2) Always Below 1 Ω
B1-44 (VHI2) or B8-1 (VHI2) - Body ground and other terminals Always 10 kΩ or higher
B1-84 (HIN2) or B8-2 (HIN2) - Body ground and other terminals Always 10 kΩ or higher



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B1)Location & Routing

Click Connector(B1)Engine Compartment>No. 2 Stack Wire>FC Control ECU

B1-44 (VHI2) or B1-84 (HIN2) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the No. 2 fuel injector assembly connector.


c.

Reconnect the FC control ECU connector.



OK

3.INSPECT NO. 2 FUEL INJECTOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT NO. 2 FUEL INJECTOR ASSEMBLY

OK

NG

REPLACE NO. 2 FUEL INJECTOR ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (FC CONTROL ECU - BODY GROUND)

Pre-procedure1

a.

Disconnect the FC control ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B1)Location & Routing

Click Connector(B1)Engine Compartment>No. 2 Stack Wire>FC Control ECU

B1-104 (E1) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the FC control ECU connector.



OK

5.CHECK HARNESS AND CONNECTOR (FC CONTROL ECU - FC-B RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (FC CONTROL ECU - FC-B RELAY)

Pre-procedure1

a.

Disconnect the FC control ECU connector.


b.

Remove the FC-B relay from the No. 1 front compartment relay block.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A48)Location & Routing

Click Connector(A48)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>FC Control ECU

A48-2 (+BP3) - 5 (FC-B relay holder) Always Below 1 Ω
A48-2 (+BP3) or 5 (FC-B relay holder) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reinstall the FC-B relay.


b.

Reconnect the FC control ECU connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR