Home › Engine / Hybrid System › FC CONTROL › FC CONTROL SYSTEM › 2020.11–2021.08
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466766 FC CONTROL SYSTEM C

FC CONTROL  FC CONTROL SYSTEM  P1E7A18  Air Shunt Valve Circuit Current Below Threshold  P1E7A19  Air Shunt Valve Circuit Current Above Threshold  


DESCRIPTION

In the FC system, the air shunt valve includes a function to introduce air into the exhaust drainage pipe in order to dilute the hydrogen present in the exhaust gas.

The air shunt valve introduces air in response to commands received from the FC control ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1E7A18 Air Shunt Valve Circuit Current Below Threshold All of the following conditions are met, and there is an open circuit in the air shunt valve (motor) circuit for 1 second or more continuously when an open circuit is confirmed during the initial check.
·

No +B low voltage when ignition switch is ON

·

Valve drive power source (+BP3) is 9 V or higher


(1 trip detection logic)
·

FC air by-pass valve assembly (air shunt valve (motor))

·

FC control ECU

·

Wire harness or connector


Master Warning: Comes on FC A
P1E7A19 Air Shunt Valve Circuit Current Above Threshold All of the following conditions are met, and there is a short to ground in the air shunt valve (motor) circuit for 1 second or more continuously when there is an operation standby condition during the initial check.
·

No +B low voltage when ignition switch is ON

·

Valve drive power source (+BP3) is 9 V or higher


(1 trip detection logic)
·

FC air by-pass valve assembly (air shunt valve (motor))

·

FC control ECU

·

Wire harness or connector


Master Warning: Comes on FC A

Detection timing
Vehicle Condition FC shutdown
(ignition switch ON)
FC startup process FC intermittent operation FC is generating power
(vehicle is in stationary)
FC is generating power
(vehicle is traveling)
FC shutdown process
Data List (EV)
"FC Work Mode"
Stop Startup Working Finishing
Data List (EV)
"FC Intermittent Operation"
OFF ON OFF OFF
DTC Detection ○ - - - - -

Related Data List
DTC No. Data List
P1E7A18
·

Air Shunt Valve Motor Duty

·

Air Shunt Valve Position Sensor Voltage


P1E7A19

HINT:

It is suspected that the air shunt valve or FC control ECU has a malfunction, or open or short circuit.


WIRING DIAGRAM

A477007E05
0.531,0.51 1.448,0.708 0.917,0.198 10 false FC-B NO. 1 3.5,0.375 4.417,0.573 0.917,0.198 10 false +BP3 1.625,2.438 2.542,2.635 0.917,0.198 10 false IGCT NO. 2 0.594,3.833 1.229,4.302 0.635,0.469 10 false Auxiliary Battery 2.313,1.688 2.479,1.854 0.167,0.167 10 false 5 1.51,2.052 1.677,2.219 0.167,0.167 10 false 2 2.313,2.052 2.479,2.219 0.167,0.167 10 false 1 1.51,1.688 1.677,1.854 0.167,0.167 10 false 3 1.479,0.625 1.646,0.792 0.167,0.167 10 false 2 2.281,0.615 2.448,0.781 0.167,0.167 10 false 1 2.281,0.25 2.448,0.417 0.167,0.167 10 false 5 1.469,0.25 1.635,0.417 0.167,0.167 10 false 3 3.51,3.25 4.427,3.448 0.917,0.198 10 false E03 3.708,3.76 4.104,4.146 0.396,0.385 10 false A48 4.75,1.156 5.667,1.354 0.917,0.198 10 false ABV1 4.75,1.677 5.667,1.875 0.917,0.198 10 false ABV2 6.26,1.99 6.802,2.156 0.542,0.167 10 false Motor 5.719,1.146 5.885,1.313 0.167,0.167 10 false 2 5.708,1.667 5.875,1.833 0.167,0.167 10 false 1 5.833,2.573 6.917,3.365 1.083,0.792 10 false FC Air By-pass Valve Assembly (Air Shunt Valve) 5.833,2.385 6.25,2.646 0.417,0.26 10 false B15 5.188,1.677 5.417,1.844 0.229,0.167 10 false 33 5.177,1.156 5.406,1.323 0.229,0.167 10 false 32 3.313,0.26 3.542,0.427 0.229,0.167 10 false 2 3.271,3.125 3.552,3.292 0.281,0.167 10 false 21 1.729,1 2.646,1.198 0.917,0.198 10 false FC-B 3.708,3.906 4.844,4.24 1.135,0.333 10 false FC Control ECU 4.583,0.74 5.042,0.938 0.458,0.198 10 false +BP3 1.594,3.948 2.688,4.354 1.094,0.406 10 false EV Control ECU 0.417,0.896 1.333,1.094 0.917,0.198 10 false R/B-B NO. 1 0.406,1.448 1.323,1.646 0.917,0.198 10 false R/B FR 0.604,1.948 1.521,2.146 0.917,0.198 10 false IGCT NO. 2 0.573,2.99 1.292,3.333 0.719,0.344 10 false R/R RR# 2 1.646,3.333 2.24,3.563 0.594,0.229 10 false MREL 1.594,3.792 2.083,3.969 0.49,0.177 10 false A8*1 1.396,3.219 1.594,3.375 0.198,0.156 10 false 21 5.896,1.156 6.813,1.354 0.917,0.198 10 false ABV1 5.885,1.667 6.802,1.865 0.917,0.198 10 false ABV2 2.583,1.24 3.5,1.438 0.917,0.198 10 false IGCT NO. 6 2.521,0.51 3.438,0.708 0.917,0.198 10 false FC-B NO. 4 1.979,3.781 2.469,3.958 0.49,0.177 10 false D15*2 5.656,3.927 6.583,4.104 0.927,0.177 10 false *1: for LHD 5.677,4.271 6.604,4.448 0.927,0.177 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Put the shift state in park (P) and turn the ignition switch to ON (READY), and wait until the "FC Work Mode" in the Data List switches over from Startup to Working.



PROCEDURE

1.INSPECT FC AIR BY-PASS VALVE ASSEMBLY (AIR SHUNT VALVE (MOTOR))

OK

2.CHECK HARNESS AND CONNECTOR (FC CONTROL ECU - FC AIR BY-PASS VALVE ASSEMBLY (AIR SHUNT VALVE (MOTOR)))

NG

REPLACE FC AIR BY-PASS VALVE ASSEMBLY (AIR SHUNT VALVE (MOTOR))

2.CHECK HARNESS AND CONNECTOR (FC CONTROL ECU - FC AIR BY-PASS VALVE ASSEMBLY (AIR SHUNT VALVE (MOTOR)))

Pre-procedure1

a.

Disconnect the FC control ECU connector.


b.
A476968

Disconnect the FC air by-pass valve assembly (air shunt valve (motor)) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A48,B15)Location & Routing

Click Connector(A48)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>FC Control ECU

Click Connector(B15)Engine Compartment>No. 2 Stack Wire>FC Air By-Pass Valve Assembly

A48-32 (ABV1) - B15-2 (ABV1) Always Below 1 Ω
A48-33 (ABV2) - B15-1 (ABV2) Always Below 1 Ω
A48-32 (ABV1) or B15-2 (ABV1) - Body ground and other terminals Always 10 kΩ or higher
A48-33 (ABV2) or B15-1 (ABV2) - Body ground and other terminals Always 10 kΩ or higher



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A48)Location & Routing

Click Connector(A48)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>FC Control ECU

A48-32 (ABV1) or A48-33 (ABV2) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the FC air by-pass valve assembly (air shunt valve (motor)) connector.


c.

Reconnect the FC control ECU connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR