Home › Engine / Hybrid System › FC CONTROL › FC CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466766 FC CONTROL SYSTEM C

FC CONTROL  FC CONTROL SYSTEM  P1EF394  Fuel Cell Control Module Unexpected Operation  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1EF394 Fuel Cell Control Module Unexpected Operation A malfunction is detected when any of following processes has had an unexpected result.
·

EV control ECU (main CPU) calculation process

·

EV control ECU (main CPU) sending/receiving process

·

FC control ECU calculation process

·

FC control ECU sending/receiving process

·

FC control ECU input process (sensor input, etc.)


·

EV control ECU

·

FC control ECU

·

Hydrogen secondary pressure sensor


Master Warning: Comes on EV B

Detection timing
Vehicle Condition FC shutdown
(ignition switch ON)
FC startup process FC intermittent operation FC is generating power
(vehicle is in stationary)
FC is generating power
(vehicle is traveling)
FC shutdown process
Data List (EV)
"FC Work Mode"
Stop Startup Working Finishing
Data List (EV)
"FC Intermittent Operation"
OFF ON OFF OFF
DTC Detection ○ ○ ○ ○ ○ ○

HINT:

By accessing the "FC Work Mode" and "FC Intermittent Operation" in the freeze frame data, the FC system condition at the time the malfunction occurred can be checked.


Related Data List
DTC No. Data List
P1EF394
·

Target Mass Air Flow

·

Mass Air Flow (Filtered Value)

·

FC System Status

·

Target Low-Range Hydrogen Pressure

·

Low-Range Hydrogen Pressure (Filtered Value)

·

Exhaust Drainage Valve



CAUTION / NOTICE / HINT

NOTICE:
·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the ignition switch to ON (READY) and wait for 1 minute or more.

2.

Turn the ignition switch off and wait for 10 minutes or more.

3.

Turn the ignition switch to ON (READY) and wait for 1 minute or more.

4.

Turn the ignition switch off and wait for 10 minutes or more.

5.

Turn the ignition switch to ON (READY) and wait for 1 minute or more.



PROCEDURE

1.CHECK DTC OUTPUT
NOTICE:

The freeze frame data is cleared when DTCs are cleared. Be sure to make a note of necessary data in advance.


Pre-procedure1

a.

None


Procedure1

a.

According to the display on the GTS, check for DTCs in the Health Check.

Result:
Result Proceed to
Only P1EF394 is output A
P1EF394 is output and DTCs other than the DTCs in the table below are output B
P1EF394 is output and any DTCs in the table below are output C

Malfunction Content Relevant DTC
Communication system malfunction P1E7E87 (FC) Lost Communication with Hybrid/EV Powertrain Control Module (SIL) Missing Message
P1E7F87 (EV) Communication Error from Fuel Cell Control Module to Hybrid/EV Powertrain Control Module Missing Message
Sensor and actuator circuit malfunction P1DBA11 (FC) Low-Range Hydrogen Pressure Sensor Circuit Short to Ground
P1DBA15 (FC) Low-Range Hydrogen Pressure Sensor Circuit Short to Battery or Open
System malfunction P1D2496 (EV) Hydrogen Pump Component Internal Failure
P1D7F62 (EV) FC Air Compressor Motor Signal Compare Failure
P1D7F96 (EV) FC Air Compressor Motor Component Internal Failure
P1DC000 (EV) Low-Range Hydrogen Pressure Too Low
P1DC100 (EV) Low-Range Hydrogen Pressure Too High
P1DC500 (EV) FC Air Pressure Too High
P1DDF00 (EV) FC Air Flow Malfunction
P1DDF79 (EV) FC Air Flow Mechanical Linkage Failure
P1E4000 (EV) Extreme Hydrogen Leak (Motor Room)
P1E407A (EV) Hydrogen Leak (Motor Room) Fluid Leak or Seal Failure
P1E4100 (EV) Extreme Hydrogen Leak (Tank Area 1)
P1E417A (EV) Hydrogen Leak (Tank Area 1) Fluid Leak or Seal Failure
P1E4862 (EV) FC Stack Inlet Pressure Sensor/Barometric Pressure Sensor "B" Signal Compare Failure
P1EF394 (EV) Fuel Cell Control Module Unexpected Operation
P1EF600 (EV) Extreme Hydrogen Leak (Tank Area 2)
P1EF67A (EV) Hydrogen Leak (Tank Area 2) Fluid Leak or Seal Failure


HINT:

DTC P1EF394 may be store due to problems that cause the DTCs shown above to output. If such happens, troubleshoot the suspected area(s) corresponding to the output DTC(s) in order of the listed DTCs shown in the table above.



Post-procedure1

a.

Turn the ignition switch off.



A

2.READ VALUE USING GTS (LOW-RANGE HYDROGEN PRESSURE (FILTERED VALUE))

B

2.READ VALUE USING GTS (LOW-RANGE HYDROGEN PRESSURE (FILTERED VALUE))

C

GO TO DTC CHART

2.READ VALUE USING GTS (LOW-RANGE HYDROGEN PRESSURE (FILTERED VALUE))

Pre-procedure1

a.

Remove the hydrogen secondary pressure sensor (low-range hydrogen pressure sensor).

HINT:

Click hereEngine / Hybrid System>FC CONTROL>HYDROGEN PRESSURE SENSOR>REMOVAL



b.

Reconnect the hydrogen secondary pressure sensor (low-range hydrogen pressure sensor) connector.


Procedure1

a.

Read the value displayed on the GTS.

Powertrain > EV > Data List
Tester Display
Low-Range Hydrogen Pressure (Filtered Value)
50003 397 1032

b.

Using the table, read the normal atmospheric pressure value for the applicable altitude.

A479641C01
0.177,0.063 0.49,0.26 0.313,0.198 10 false *a 0.396,0.51 0.708,0.708 0.313,0.198 10 false *b 2.719,0.51 3.031,0.708 0.313,0.198 10 false *b 5.031,0.51 5.344,0.708 0.313,0.198 10 false *b 1.146,0.51 1.458,0.708 0.313,0.198 10 false *c 3.438,0.5 3.75,0.698 0.313,0.198 10 false *c 5.729,0.5 6.042,0.698 0.313,0.198 10 false *c 1.802,0.5 2.115,0.698 0.313,0.198 10 false *d 4.125,0.51 4.438,0.708 0.313,0.198 10 false *d 6.396,0.521 6.708,0.719 0.313,0.198 10 false *d
*a Altitude, Temperature and Atmospheric Pressure Correlation Table *b Altitude (m (ft.))
*c Temperature (°C (°F)) *d Atmospheric Pressure (kPa (psi))


HINT:
·

Standard atmospheric pressure is approximately 101 kPa (15 psi).

·

For every 100 m (328 ft.) increase in altitude, atmospheric pressure drops by approximately 1 kPa (0.1 psi). This varies by weather.




c.

Compare the "Low-Range Hydrogen Pressure (Filtered Value)" values in the Data List with the normal atmospheric value from the table.

Result:
Result Proceed to
Difference between "Low-Range Hydrogen Pressure (Filtered Value)" in Data List and normal atmospheric pressure value is 35 kPa or more. A
Other than above. B



Post-procedure1

a.

Turn the ignition switch off.



A

REPLACE HYDROGEN SECONDARY PRESSURE SENSOR

B

3.REPLACE FC CONTROL ECU
3.REPLACE FC CONTROL ECU
HINT:

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CLEAR DTC
4.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Powertrain > EV > Clear DTCs
50002 397
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for 10 minutes or more.



NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT

Pre-procedure1

a.

Turn the ignition switch to ON (READY) and wait for 120 seconds or more.


b.

Turn the ignition switch off and wait for 10 minutes or more.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
DTCs are not output A
P1EF394 is output B



Post-procedure1

a.

Turn the ignition switch off.



A

END

B