The air system of the FC system feeds the FC stack with oxygen, so that the FC stack can generate power. The air system calculates air volume appropriate to the amount of power the FC stack has to generate, and regulates the FC air compressor speed according to such estimated air volume.
The EV control ECU stores a DTC when the speed is not being controlled according to the target air compressor speed.
For the circuit diagram, refer to P1DDF00.
Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>P1DDF00
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | DTC Output from | Priority |
|---|---|---|---|---|---|---|
| P1D7F96 | FC Air Compressor Motor Component Internal Failure | Detected if the "FC Work Mode" is Working mode and the following condition is met:
Significant difference has been found between the actual and target air compressor speeds (1 trip detection logic) |
·
FC stack assembly ·
Air system lines ·
Air pipes (intake, supply, exhaust systems) ·
FC air compressor with motor assembly ·
FC air pressure regulator assembly (air pressure regulating valve) ·
FC air by-pass valve assembly (air shunt valve) ·
FC air pressure regulator assembly (air sealing valve) |
Master Warning: Comes on | EV | B |
| Vehicle Condition | FC shutdown
(ignition switch ON) |
FC startup process | FC intermittent operation | FC is generating power
(vehicle is in stationary) |
FC is generating power
(vehicle is traveling) |
FC shutdown process |
|---|---|---|---|---|---|---|
| Data List
"FC Work Mode" |
Stop | Startup | Working | Finishing | ||
| Data List
"FC Intermittent Operation" |
OFF | ON | OFF | OFF | ||
| DTC Detection | - | ○ | - | ○ | ○ | - |
By accessing the "FC Work Mode" and "FC Intermittent Operation" in the freeze frame data, the FC system condition at the time the malfunction occurred can be checked.
| DTC No. | Data List |
|---|---|
| P1D7F96 | ·
Target Mass Air Flow ·
Mass Air Flow (Filtered Value) ·
FC Air Compressor Motor Speed ·
Target FC Air Compressor Motor Speed ·
Target FC Inlet Air Pressure ·
FC Inlet Air Pressure (Filtered Value) ·
FC Air Compressor Consumption Power ·
Air Pressure Regulating Valve Position ·
Air Shunt Valve Position ·
Air Sealing Valve Position |
| DTC No. | Active Test |
|---|---|
| P1D7F96 | Control the FC Air Compressor |
This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.
When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Drive the vehicle for 10 minutes according to the freeze frame data (Vehicle Speed, Accelerator Degree, etc.).
Perform this road test only in an appropriate safe location, in accordance with all local laws.
Perform the "Control the FC Air Compressor" Active Test. Check that the difference between the set speed in the Active Test and the "FC Air Compressor Motor Speed" in the Data List is within 200 rpm.
The freeze frame data is cleared when DTCs are cleared. Be sure to make a note of necessary data in advance.
Pre-procedure1
None
Procedure1
According to the display on the GTS, check for DTCs in the Health Check.
| Result | Proceed to |
|---|---|
| Only P1D7F96 is output | A |
| P1D7F96 is output and DTCs other than the DTCs in the table below are output | B |
| P1D7F96 is output and any DTCs in the table below are output | C |
| Malfunction Content | Relevant DTC | |
|---|---|---|
| Microcomputer malfunction | P1D0400 (Hybrid (EV) Control System) | FC Air Compressor Motor Control Module A/D Processing Performance |
| P1D8F47 (Hybrid (EV) Control System) | FC Air Compressor Motor Control Module Watchdog / Safety MCU Failure | |
| P1D0500 (Hybrid (EV) Control System) | FC Air Compressor Motor Control Module RAM/ROM Error | |
| P1D8F49 (Hybrid (EV) Control System) | FC Air Compressor Motor Control Module Internal Electronic Failure | |
| P1D8F04 (Hybrid (EV) Control System) | FC Air Compressor Motor Control Module System Internal Failure | |
| P1E8649 (Hybrid (EV) Control System) | FC Air Compressor Motor Position Sensor Internal Electronic Failure | |
| P1E3B87 (Hybrid (EV) Control System) | Communication Error from FC Air Compressor Motor to Drive Motor "A" Missing Message | |
| P1D8F00 (Hybrid (EV) Control System) | FC Air Compressor Motor Control Module Performance | |
| P1E8800 (Hybrid (EV) Control System) | FC Air Compressor Motor Position Sensor REF Signal Oscillation Stop | |
| P1E8738 (Hybrid (EV) Control System) | FC Air Compressor Motor Position Sensor REF Signal Frequency Incorrect | |
| Sensor and actuator circuit malfunction | P1D701C (Hybrid (EV) Control System) | FC Air Compressor Inverter Temperature Sensor Circuit Voltage Out of Range |
| P1D7011 (Hybrid (EV) Control System) | FC Air Compressor Inverter Temperature Sensor Circuit Short to Ground | |
| P1D7015 (Hybrid (EV) Control System) | FC Air Compressor Inverter Temperature Sensor Circuit Short to Battery or Open | |
| P1D701F (Hybrid (EV) Control System) | FC Air Compressor Inverter Temperature Sensor Circuit Intermittent | |
| P1D7516 (Hybrid (EV) Control System) | FC Air Compressor Motor Position Sensor Circuit Voltage Below Threshold | |
| P1D751C (Hybrid (EV) Control System) | FC Air Compressor Motor Position Sensor Circuit Voltage Out of Range | |
| P1D7522 (Hybrid (EV) Control System) | FC Air Compressor Motor Position Sensor Signal Amplitude > Maximum | |
| P1D7A1C (Hybrid (EV) Control System) | FC Air Compressor Motor Temperature Sensor Circuit Voltage Out of Range | |
| P1D7A11 (Hybrid (EV) Control System) | FC Air Compressor Motor Temperature Sensor Circuit Short to Ground | |
| P1D7A15 (Hybrid (EV) Control System) | FC Air Compressor Motor Temperature Sensor Circuit Short to Battery or Open | |
| P1D7A1F (Hybrid (EV) Control System) | FC Air Compressor Motor Temperature Sensor Circuit Intermittent | |
| P1E9362 (Hybrid (EV) Control System) | FC Air Compressor Motor Phase V Current Sensor "A"/"B" Signal Compare Failure | |
| P1F0E1C (Hybrid (EV) Control System) | FC Air Compressor Motor Phase V Current Sensor "A" Circuit Voltage Out of Range | |
| P1F101C (Hybrid (EV) Control System) | FC Air Compressor Motor Phase V Current Sensor "B" Circuit Voltage Out of Range | |
| P1F1228 (Hybrid (EV) Control System) | FC Air Compressor Motor Phase V Current Sensor "A"/"B" Signal Bias Level Out of Range / Zero Adjustment Failure | |
| P1E9462 (Hybrid (EV) Control System) | FC Air Compressor Motor Phase W Current Sensor "A"/"B" Signal Compare Failure | |
| P1F0F1C (Hybrid (EV) Control System) | FC Air Compressor Motor Phase W Current Sensor "A" Circuit Voltage Out of Range | |
| P1F111C (Hybrid (EV) Control System) | FC Air Compressor Motor Phase W Current Sensor "B" Circuit Voltage Out of Range | |
| P1F1328 (Hybrid (EV) Control System) | FC Air Compressor Motor Phase W Current Sensor "A"/"B" Signal Bias Level Out of Range / Zero Adjustment Failure | |
| P260031 (Hybrid (EV) Control System) | Motor/Generator Coolant Pump "A" Control Circuit No Signal | |
| P26009E (Hybrid (EV) Control System) | Motor/Generator Coolant Pump "A" Control Circuit Stuck On | |
| System malfunction | P1F141D (Hybrid (EV) Control System) | FC Air Compressor Motor Circuit Current Out of Range |
| P1D7F00 (Hybrid (EV) Control System) | FC Air Compressor Motor Performance | |
| P334F00 (Hybrid (EV) Control System) | FC Air Compressor Inverter Overcurrent (Control Module Performance) | |
| P337F00 (Hybrid (EV) Control System) | FC Air Compressor Inverter Overcurrent (Inverter Performance) | |
| P336F00 (Hybrid (EV) Control System) | FC Air Compressor Inverter Overcurrent (Position Sensor Circuit Range/Performance) | |
| P338F00 (Hybrid (EV) Control System) | FC Air Compressor Inverter Overcurrent (System Performance) | |
| P1E8E00 (Hybrid (EV) Control System) | FC Air Compressor Motor Torque Delivered Performance | |
| P1D824B (Hybrid (EV) Control System) | FC Air Compressor Inverter Over Temperature | |
| P1EF800 (Hybrid (EV) Control System) | FC Air Compressor Inverter Circuit Short (Control Module Performance) | |
| P1EFB00 (Hybrid (EV) Control System) | FC Air Compressor Inverter Circuit Short (Inverter Performance) | |
| P1EF900 (Hybrid (EV) Control System) | FC Air Compressor Inverter Circuit Short (Position Sensor Circuit Range/Performance) | |
| P1D829E (Hybrid (EV) Control System) | FC Air Compressor Inverter Fail Signal Stuck On | |
| P1EFA00 (Hybrid (EV) Control System) | FC Air Compressor Inverter Circuit Short (System Performance) | |
| P260096 (Hybrid (EV) Control System) | Motor/Generator Coolant Pump "A" Control Circuit Component Internal Failure | |
DTC P1D7F96 may be store due to problems that cause the DTCs shown above to be output. If such happens, troubleshoot the suspected area(s) corresponding to the output DTC(s) in order starting with the listed DTCs shown in the table above.
Post-procedure1
Turn the ignition switch off.
A
B
C
Hybrid (EV) Control System:
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Check that the air cleaner filter element sub-assembly is not clogged.
The air cleaner filter element sub-assembly is not clogged
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clean or replace the air cleaner filter element sub-assembly.
| Proceed to |
|---|
| NEXT |
NEXT
Check that no air comes in without flowing through each part of the intake air system and the exhaust drainage pipe is not clogged, disconnected, or damaged.
The intake and exhaust piping is not clogged, disconnected or damaged
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Remove the FC air pressure regulator assembly (air sealing valve).
Procedure1
Visually check the FC air pressure regulator assembly (air sealing valve).
The valve shaft is not bent or otherwise damaged
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Install the FC air pressure regulator assembly (air sealing valve).
OK
NG
Pre-procedure1
Remove the FC air pressure regulator assembly (air pressure regulating valve).
Procedure1
Visually check the FC air pressure regulator assembly (air pressure regulating valve).
The valve shaft is not bent or otherwise damaged
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Install the FC air pressure regulator assembly (air pressure regulating valve).
OK
NG
Pre-procedure1
Remove the FC air by-pass valve assembly (air shunt valve).
Click hereEngine / Hybrid System>INTAKE / EXHAUST>AIR BYPASS VALVE>REMOVAL
Procedure1
Visually check the FC air by-pass valve assembly (air shunt valve).
The valve shaft is not bent or otherwise damaged
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Install the FC air by-pass valve assembly (air shunt valve).
OK
NG
Pre-procedure1
Turn the ignition switch to ON (READY).
Drive the vehicle for 10 minutes according to the freeze frame data (Vehicle Speed, Accelerator Degree, etc.)
Perform this road test only in an appropriate safe location, in accordance with all local laws.
If vehicle speeds, accelerator pedal positions, road conditions, ambient temperatures and climates at the time the malfunction occurred can be found out, take them into account.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| P1D7F96 is output | B |
Post-procedure1
Turn the ignition switch off.
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B