| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | PACKAGE TRAY TRIM PANEL ASSEMBLY | 64330 | - | - | - |
| 2 | NO. 2 PACKAGE TRAY TRIM PANEL ASSEMBLY | 64340B | - | - | - |
| *A | w/ Sunshade | - | - |
| *1 | CLIP | - | - |
| ● | Non-reusable part | - | - |
| *A | for 2-piece Type | *B | for 1-piece Type |
| ● | Non-reusable part | - | - |
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the back window glass removal/installation are shown below.
Be sure to use the back window assembly adhesive (specialized for high-rigidity specification vehicles) as the adhesive for replacing the back window assembly.
Be sure to use the back window assembly adhesive (specialized for high-rigidity specification vehicles) as the adhesive for adjusting the back window assembly.
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
| Effect/Inoperative Function When Necessary Procedures are not Performed | Necessary Procedures | Link |
|---|---|---|
| Air conditioning system | After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. | - |
64330
1.REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY
64340B
2.REMOVE NO. 2 PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Sunshade)
8974E
3.REMOVE ROOF HEADER ELECTRICAL KEY ANTENNA
81952H
7.REMOVE CENTER STOP LIGHT COVER RH
|
Use the same procedure described for the LH side. |
81497
10.REMOVE REAR COMBINATION LIGHT COVER RH
|
Use the same procedure described for the LH side. |
64713J
12.REMOVE NO. 1 LUGGAGE COMPARTMENT UPPER COVER RH
|
Use the same procedure described for the LH side. |
64571B
14.REMOVE LUGGAGE COMPARTMENT DOOR HINGE COVER RH
|
Use the same procedure described for the LH side. |
64810
15.REMOVE BACK WINDOW ASSEMBLY
|
|
| *a | When new the Back Window Assembly | *b | When reusing the Back Window Assembly |
| *c | Matchmarks | - | - |
|
Protective Tape | - | - |
Apply protective tape on the body surface around the outer edge of the back window assembly.
When reusing the back window assembly, apply adhesive tape to the back window assembly and body panel, and place matchmarks using a pen before removing.
Disconnect 4 connector.
| *a | Cut | - | - |
Using a utility knife, cut at the position shown in the illustration of the back window outside moulding and remove.
Do not damage the back window assembly or body surface.
If the body panel is damaged, perform rust-prevention treatment after removing the back window assembly.
| *a | Suction Cups | - | - |
Install the suction cups to the back window assembly.
When using a piano wire, perform the following procedure.
1. 1. Pass the piano wire (0.6 mm is appropriate) and install both ends on the mighty puller as shown in the illustration.
2. Pull the piano wire back and forth and cut through the adhesive of the back window assembly leaving the windshield glass stopper.
When working near the connector, be careful not to damage it with the piano wire.
Do not forcefully allow the piano wire to come to contact with the edges of the back window assembly.
Be careful as the piano wire will break if it crosses itself.
| *A | for 1-piece Type | *B | for 2-piece Type |
| *1 | No. 1 Back Window Glass Stopper | *2 | No. 2 Back Window Glass Stopper |
Holding the suction cups, detach the No. 1 back window glass stopper and No. 2 back window glass stopper, and remove the back window assembly.
Be careful not to drop the back window assembly.
75573F
16.REMOVE BACK WINDOW OUTSIDE MOULDING
When reusing the back window assembly:
| *a | Backside | - | - |
Using a scraper, remove the back window outside moulding.
Do not damage the back window assembly.
Always replace the installed back window outside moulding with a new back window outside moulding.
64813D
17.REMOVE BACK WINDOW GLASS ADHESIVE DAM
When reusing the back window assembly:
| *a | Backside | - | - |
Using a scraper, remove the back window glass adhesive dam.
Do not damage the back window assembly.
Always replace the installed back window glass adhesive dam with a new back window glass adhesive dam.
56112A
18.REMOVE WINDOW GLASS ADHESIVE DAM
When reusing the back window assembly:
| *a | Backside | - | - |
Using a scraper, remove the 6 window glass adhesive dams.
Do not damage the back window assembly.
Always replace the installed window glass adhesive dam with a new window glass adhesive dam.
56119F
19.REMOVE WINDSHIELD GLASS SEAL
When reusing the back window assembly:
| *a | Backside | - | - |
Using a scraper, remove the windshield glass seal.
Do not damage the back window assembly.
Always replace the installed windshield glass seal with a new windshield glass seal.
81979
20.REMOVE CENTER STOP LIGHT BRACKET LH
When reusing the back window assembly:
| *a | Backside | - | - |
Using a scraper, remove the center stop light bracket LH.
Do not damage the back window assembly.
81978A
21.REMOVE CENTER STOP LIGHT BRACKET RH
When reusing the back window assembly:
| *a | Backside | - | - |
Using a scraper, remove the center stop light bracket RH.
Do not damage the back window assembly.
82214D
22.REMOVE CENTER STOP LIGHT WIRE
When reusing the back window assembly:
| *a | Backside | - | - |
Using a scraper, remove the center stop light wire.
Do not damage the back window assembly.
Always replace the installed center stop light wire with a new center stop light wire.
56115B
23.REMOVE NO. 1 BACK WINDOW GLASS STOPPER
When reusing the back window assembly:
| *a | Backside | - | - |
for 1-piece Type:
Using a scraper, remove the 2 No. 1 back window glass stoppers.
Do not damage the back window assembly.
Always replace the installed No. 1 back window glass stopper with a new 2-piece type No. 1 back window glass stopper.
for 2-piece Type:
Remove the 2 No. 1 window glass stoppers from the body.
Always replace the installed No. 1 back window glass stopper with a new 2-piece type No. 1 back window glass stopper.
56116D
24.REMOVE NO. 2 BACK WINDOW GLASS STOPPER
When reusing the back window assembly:
| *a | Backside | - | - |
Using a scraper, remove the 2 No. 2 back window glass stoppers.
Do not damage the back window assembly.
Always replace the installed No. 2 back window glass stopper with a new 2-piece type No. 2 back window glass stopper.